Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DWE560-XE
Summary of Contents for DeWalt DWE560-XE
- Page 1 INSTRUCTION MANUAL DWE560-XE, DWE565-XE 184 mm (7-1/4") CIRCULAR SAW...
-
Page 3: Definitions: Safety Guidelines
This may Technical Data significantly increase the exposure level over the total working period. DWE560-XE DWE565-XE An estimation of the level of exposure to vibration should also take into account Voltage the times when the tool is switched off or when it is running but not actually doing the job. - Page 4 GENERAL POWER TOOL SAFETY WARNINGS f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of WARNING! Read all safety warnings and all instructions. Failure to follow electric shock.
-
Page 5: Extension Cords
c) Disconnect the plug from the power source and/or the battery pack from • Replacement of the supply cord. If the supply cord or plug is damaged, it must the power tool before making any adjustments, changing accessories, be replaced by the manufacturer or an authorised D WALT Service Centre in or storing power tools. -
Page 6: Further Safety Instructions For All Saws
Further Safety Instructions for All Saws LOWER GUARD SAFETY INSTRUCTIONS a) Check lower guard for proper closing before each use. Do not operate the saw CAUSES AND OPERATOR PREVENTION OF KICKBACK: if lower guard does not move freely and close instantly. Never clamp or tie the –... -
Page 7: Components (Fig. 1)
• Always make sure the saw is clean before using. work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Stop using this saw and have it properly serviced if any unusual noise or abnormal operation occcurs. -
Page 8: Changing Blades
ADJUSTMENTS Changing Blades WARNING: To reduce the risk of serious personal injury, turn tool off and DWE560-XE disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. TO INSTALL THE BLADE (FIG. 2–5) WARNING: The inner flange has a 20 mm diameter on one side and a 19 mm diameter on the other. - Page 9 check the condition and operation of the lower blade guard to assure that it is 2. Remove the blade clamping screw (J) and outer clamp washer (N). Remove old working properly. Make sure it moves freely and does not touch the blade or any blade.
- Page 10 Your depth is set. The full range of bevel adjustment on the DWE560-XE is 0 to 48°. The pivot bracket is 3. For the most efficient cutting action using a carbide tipped saw blade, set the graduated in increments of 5°.
- Page 11 2. Rotate the cord protector clockwise to the parallel position. FIG. 10 FIG. 12 DWE560-XE TO OBTAIN THE VERICAL POSITION (FIG. 13) 1. Press the cord protector (V) in as indicated by the arrow. 2. Rotate the cord protector counterclockwise to the vertical position.
-
Page 12: Operation
Proper hand position requires one hand on FIG. 14A the main handle (B), with the other hand on DWE560-XE the auxiliary handle (E). Switch (Fig. 1) For safety reasons the trigger switch (A) of your tool is equipped with a lock-off button (M). - Page 13 ALWAYS DISCONNECT SAW BEFORE MAKING ANY ADJUST MENTS! Place the work FIG. 18 FIG. 19 with its “good” side—the one on which appearance is most important—down. The saw cuts upward, so any splintering will be on the work face that is up when you saw it.
- Page 14 Kickback RIPPING (FIG. 20) FIG. 20 Ripping is the process of cutting wider When the saw blade becomes pinched or twisted in the cut, kickback can occur. The boards into narrower strips – cutting saw is thrust rapidly back toward the operator. When the blade is pinched or bound grain lengthwise.
-
Page 15: Maintenance
Cleaning D. Changing hand grip or body position while cutting can result in blade twist. E. Backing up the saw to clear blade can lead to twist if it is not done carefully. WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once 4. - Page 16 ADJUSTING FOR 90 DEGREE CUTS, sharpened in most areas; see SAWS-SHARPENING in the yellow pages. FIG. 23 DWE565-XE Hardened gum on the blade can be removed with kerosene, turpentine, or oven cleaner. Anti-stick coated blades can be used in applications where excessive build-up 1.
- Page 20 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (AUG12) Part No. N145839 DWE560-XE, DWE565-XE Copyright © 2012 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...