Vertex Standard VXR-7000 Operating Manual page 16

CE27 Programming Software Instruction
Rev Bst: Reverse Burst.
When this parameter is set to "on," the CTCSS tone
signal's phase is inverted just before the repeater turns
to receive. This allows the portable/mobile station's
CTCSS Decoder to begin switching off, thus reducing
the transition time required.
Press the [S ] bar to toggle "on" or "off."
PACE
DCS Typ: DCS Format
This command is effective only when DCS is chosen for
squelch control.
A = "Normal" DCS
B = "Inverted" (complement) DCS
Press the [S ] bar to select the desired DCS Type.
PACE
DDec Type: DCS Decoder Type
This command selects the manner in which DCS is to
be decoded.
Fixed = Decodes only the type selected in above pa-
rameter (DCS Typ: Normal or Inverted).
Auto = Both types (Normal and Inverted) will be
decoded.
Press the [S ] bar to select the desired DCS Decoder
PACE
Mode.
Multi Tone: Enable/disable Multi Tone Operation
Press the [S ] bar to toggle Multi Tone Operation
PACE
between selections "yes" and "no."
Press the [E ] key
NTER
to display the "M
ULTI
T S " win-
ONE ELECT
dow, from which you
may select a CTCSS
tone or DCS code;
move the cursol to the appropriate field you using the
[A ] key, then press the [E
RROW
"T S " or "C
ONE ELECT ODE
the desired CTCSS tone or DCS code using the [A
key, then press the [E
NTER
lected tone or code, or press the [E
may set as many as 16 CTCSS tones and/or DCS codes.
Note that, if you do not yet program a CTCSS tone or
DCS code in the "M
ULTI
the "M T S
ULTI ONE ELECT
grammed), press the [S
T S " window directly.
ONE ELECT
CWID ANI/ENI: Select the Identifier mode
Press the [S ] bar to toggle the selections "CW ID,"
PACE
"ANI/ENI," or "Off." To select this feature to the "CW
ID" or "ANI/ENI," the "CW ID" parameter must be en-
abled via the dealer programming.
12
] key to open the
NTER
S " window. Now select
ELECT
] key again to accept the se-
] key to cancel. You
SC
T S " window (when
ONE ELECT
" window data is not pro-
] bar to display the "M
PACE
Action Mode: Select the repeater operation mode
Press the [S
eration or "Simplex" operation.
Tx Freq.: Edit Transmit Frequency
Use the [0] - [9] keys to enter the desired channel fre-
quency directly, and press the [E
CTCSS Encoders: Toggle CTCSS Encoder ON/OFF, sets
CTCSS Frequency
Press the [S
toggle the CTCSS Encoder
"on" or "off," or press the
[E ] key to display the
NTER
"T S
ONE ELECT
from which you may select
a CTCSS frequency using the [A
] again to accept the selected tone, or press the [E
TER
key to cancel.
DCS Encoders: Toggle DCS Encoder ON/OFF, sets DCS
Code #
Press the [S
or "off," or press the [E
S " window, from which you may select a DCS code
ELECT
using the [A
] key; press
ROW
[E ] again
NTER
to accept the
selected code,
or press the
[E ] key to
S C
cancel.
Base TOT: Enable/disable the Time-Out Timer while in the
"BASE" station mode
Press the [S
"yes" and "no."
]
RROW
The TOT time is determined via dealer programming.
Base Guard: Enable/disable the Base Guard Feature
When this parameter is set to "yes," the transmitter will
be inhibited for a few seconds before the repeater (in
the "BASE" station mode) turns to receive.
The inhibit time is determined via dealer programming.
ULTI
LOUT: Select the Lock Out Feature's mode
Press the [S
tween "BCLO," "BTLO," or "off," then press the [En-
ter] key to accept the setting. "BCLO" inhibits trans-
mitting while there is carrier present. "BTLO" inhibits
transmitting while there is carrier present unless there
also is a valid tone present.
VXR-7000 FM R
] bar to toggle between "Duplex" op-
PACE
NTER
] bar to
PACE
" window,
RROW
] bar to toggle the DCS Encoder "on"
PACE
] key to display the "C
NTER
-
R
] bar to toggle the TOT feature selects
PACE
] bar to toggle the Lock Out Feature be-
PACE
O
EPEATER PERATING
] key.
] key; press [E -
N
]
SC
ODE
M
ANUAL