Marantz SR4003 User Manual page 34

CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
2. 3.
ST V – OFF NIGHT PEAK ATT ANALOG SURROUND
DIGITAL DIGITAL
DISC 6.1 MT X 6.1 SPKR B EQ
L C R
AAC PCM LFE
SL S SR
1.
Recall the preset number to be cleared with
the method described in "Recalling" a preset
station.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller.
3.
The stored preset number blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or the CL button on the
remote controller.
4.
"xx CLEAR" appears on the display to indicate
that the specified preset number has been
cleared.
Note:
To clear all stored preset stations, press and hold the
T.MODE and the ENTER buttons for two seconds.
SORTING PRESET STATIONS
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG SURROUND
DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 SPKR B EQ DIGITAL
L C R
AAC LFE
PCM
SL S SR
2.
If you have stations memorized, and there is a gap in
the sequential order:
3.
I.e. the stations are stored as follows
1) 87.5 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 4:
To sort the numbers, press the 4 cursor button while
pressing the MEMORY button.
"PRESET SORT" will appear on the display and
sorting will be done.
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
5. 5. 4. 2. 5. 6.
SURROUND
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG
DIGITAL DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 SPKR B EQ
L C R
AAC PCM LFE
SL S SR
4.
5.
2.
5.
6.
1.
Recall the preset number to be inputted name
with the method described in "Recalling" a
preset station.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller for more than 3 seconds.
3.
The left most column of the station name
indicator fl ashes, indicating the character entry
ready status.
4.
When you press the 3 or 4 cursor buttons on
the front panel or the TUNE 3 / 4 buttons on
the remote controller, alphabetic and numeric
characters will be displayed in the following
order:
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
← DOWN
ENGLISH
5.
After selecting the fi rst character to be entered,
press the MEMORY or ENTER buttons, press
the MEMO button on the remote controller.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the
same way.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press PRESET
+ or – buttons on the remote controller.
Note:
Unused columns should be fi lled by entering blanks.
6.
To save the name, press the MEMORY button
on the front panel or remote controller for more
than 2 seconds.
Ten keypad Press, press again, press again, etc.
1
A → B → C → 1 → A
2
D → E → F → 2 → D
3 G → H → I → 3 → G
4 J → K → L → 4 → J
5 M → N → O → 5 → M
6 P → Q → R → 6 → P
7 → → → →
S T U 7 S
8 → → → →
V W X 8 V
9
Y → Z → space → 9 → Y
0
– → + → / → 0
31