Marantz LN9101M Installation Manual
Marantz LN9101M Installation Manual

Marantz LN9101M Installation Manual

Anamorphic lens system

Advertisement

Quick Links

®
Model LN9101M Installation Guide
Anamorphic Lens System

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LN9101M and is the answer not in the manual?

Questions and answers

Summary of Contents for Marantz LN9101M

  • Page 1 ® Model LN9101M Installation Guide Anamorphic Lens System...
  • Page 2: Important Safety Instructions

    The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “danger- ous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO...
  • Page 3: Additional Safety Instructions

    201-762-6666 Fax. 201-762-6687 Parts Customer Service If it is determined that your Marantz product is in need of repair, you can return it to your Dealer. You can also return it to the Marantz Service Department. For assistance on factory repair return procedure, contact the Marantz at: Marantz America, Inc.
  • Page 4: Table Of Contents

    Lens. A 1/8 inch (3.5mm) stereo mini phone plug is used for connections. Scotch- IR Connectors The LN9101M IR In Port uses a 2.5mm quad mini phone plug and allows connec- tion of other brand IR Receivers to the LN9101M. +12V DC...
  • Page 5: Dimensions

    Some of the brackets from the Marantz MT20 (op- tional ceiling mounting bracket) will be used to mount the combination of the projector and LN9101M to the ceiling. In some installations the EXT10 bracket will also be used (optional extension pole kit).
  • Page 6: Alignment

    The above illustrations are shown for purposes Plate #4 of clarity. 1/4-20 4. Place the Lens Holder Base onto the LN9101M tapped hole Sled Mounting Plate with the Lens Holder Post Screws oriented to the right. Secure the Lens Holder...
  • Page 7 Notes: The MT20 hardware, fasteners, mounting tem- plate and parts list are located in a separate shipping carton from the projector. Plate #4 supplied with the LN9101M will be used instead of the MT20 Plate #4. 1. Insert Base Plate...
  • Page 8 Align the three 6mm mounting holes on the projector with the mounting holes on Plate #4 and the LN9101M Sled. Secure the bracket to the projector using the three 6mm screws. Refer to figures 18 and 19. Figure 18...
  • Page 9 Perform the following steps: 1. Locate the external Power Supply (supplied wth the LN9101M) and connect the plug on the end of the cable to the +9V Jack on the LN9101M Sled Connection Plate. Plug the Power Supply into an active AC Outlet.
  • Page 10: Operation

    Post, the crosshatch should no longer be tilted. Do not look directly into the Lens, look off from the side at an angle. 5. Rotate the front part of the LN9101M Lens for the best focus. 6. Using the appropriate tools loosen the three...
  • Page 11: Warranty

    Marantz liability for any defective product is limited to repair or replacement of the product at Marantz’s option. Marantz shall not be liable for damage to other products caused by any defects in Marantz products, damages based upon inconvenience or loss of use of the product, or any other damages, whether incidental, consequential, or otherwise.
  • Page 12 You can find your nearest authorized distributor or dealer on our website. U. S. A. Marantz America, Inc. 100 Corporate Drive, Mahwah, NJ 07430, U. S. A. ® is a registered trademark. Printed in U. S. A. Part No. 04104000...

Table of Contents