Marantz LN7101F Installation Manual
Marantz LN7101F Installation Manual

Marantz LN7101F Installation Manual

Anamorphic lens system

Advertisement

Quick Links

®
Model LN7101F Installation Guide
Anamorphic Lens System

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LN7101F and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Marantz LN7101F

  • Page 1 ® Model LN7101F Installation Guide Anamorphic Lens System...
  • Page 2: Safety Instructions

    The lightning flash with arrowhead, The exclamation point within an within an equilateral triangle, is equilateral triangle is intended to intended to alert the user to the alert the user to the presence of im- presence of uninsulated “danger- portant operating and maintenance ous voltage”...
  • Page 3: Table Of Contents

    Customer Service Installation Guide must be adhered to as failure If it is determined that your Marantz product is in need to do so could result in serious injury. of repair, you can return it to your Dealer. You can To prevent possible damage to the Lens As- also return it to the Marantz Service Department.
  • Page 4: Table Of Contents

    MOVE THE LENS COVERS UNTIL INSTRUCT- Thank You and Please Take a Moment ....2 Technical Assistance and Customer Service ...2 6. The assembly and adjustment of the LN7101F/ Table of Contents ............3 EXT10/MT20 will require a Phillips head screw Important, Connector and Cable Information ...4 driver, adjustable wrench, 5/32 and 3/16 allen Dimensions ...............5...
  • Page 5: Dimensions

    1. The EXT10 is adjustable from 43-3/4 inches to 24 the combination of the projector and LN7101F to the inches as supplied. If the default range is accept- ceiling. In some installations the EXT10 bracket will able proceed to Step 3.
  • Page 6: Alignment

    Figure 3 LN7101F. Lens holder LN7101F Assembly Post Remove Assemble the LN7101F by performing the steps be- with screw base low: Base 1. Locate Plate #4 and the Top Locking Adjustment Ring...
  • Page 7 (indicated #1). The shipping carton from the projector. Plate #4 newly combined Plate 3 provides 10 degrees of supplied with the LN7101F will be used instead horizontal tilt. After positioning the plate, loosely of the MT20 Plate #4.
  • Page 8 6. Invert the projector and tance from the eye bolts with guide wire. place it on a soft, flat sur- 7. Before the LN7101F Lens can be installed and face. Align the three 6mm adjusted, it is important to first complete the Instal- mounting holes on the lation and Initial Settings of the VP-11 Projector.
  • Page 9 After having performed the Initial Installation and 6. While holding Tighten Screws Setup of the VP-11 Projector, the LN7101F Lens can the Lens Hold- be installed by performing the following steps: er/Lens about 2. Locate the previously two inches from...
  • Page 10: Specifications

    Do not look directly into the Lens, look off Overall Dimensions including Projector from the side at an angle. Width is 20-1/16 inches (50.9cm) 4. Rotate the front part of the LN7101F Lens for the Height is 9-13/16 inches (24.9cm) best focus. Depth is 21-15/16 inches (55.7cm) 5.
  • Page 11: Warranty

    Marantz’s option. Marantz shall not be carrier). liable for damage to other products caused by any defects in Marantz e) Any cause other than a product defect. products, damages based upon inconvenience or loss of use of the product, or any other damages, whether incidental, consequential, or 2.
  • Page 12 You can find your nearest authorized distributor or dealer on our website. U. S. A. Marantz America, Inc. 100 Corporate Drive, Mahwah, NJ 07430, U. S. A. ® is a registered trademark. Printed in U. S. A. Part No. 04104200...

Table of Contents