Advertisement
Quick Links
MODEL JVZOOO
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC1 FICATIONS
Max. cutting capacities
in wood
of stroke
2 0
mm
1
50"
6 m m
263 m m
1.6 k g
(3/4")
(2")
1
(114")
1
0 - 3 ' 4 0 0
1
(10-3/8")
(3.5
Ibs)
*
Manufacturer reserves the right t o change specifications without notice
Note: Specifications may differ from country to country.
Advertisement
Related Manuals for Makita JV2000
Summary of Contents for Makita JV2000
- Page 1 INSTRUCTION MANUAL SPEC1 FICATIONS Max. cutting capacities of stroke in wood 50" (3/4") (2") Manufacturer reserves the right t o change specifications without notice Note: Specifications may differ from country to country. 6 m m (114") 0 - 3 ' 4 0 0 MODEL JVZOOO DOUBLE INSULATION...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDLCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- INJURY, INCLUDING THE FOLLOWING: SONAL READ ALL INSTRUCTIONS. WORK AREA CLEAN. Cluttered areas and benches invite injuries. IDER WORK AREA ENVIRONMENT. Don't use power tools in damp CHILDREN AWAY. - Page 3 IMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o !e that keys and adjusting wrenches are removed from tool before turning 15. L JOlD UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger switch. Be sure switch is OFF when plugging in. UTDOOR USE EXTENSION CORDS.
-
Page 4: Additional Safety Rules
ADDITIONAL SAFETY RULES 1. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. Don't cut hollow pipe. not cut oversize workpiece. Check for the proper clearance beneath the workpiece before cutting the blade will not strike the floor, workbench, etc. Hold the tool firmly. -
Page 5: How To Use
HOW TO USE Installing jig saw blade Use the hex wrench to loosen the hex socket head bolt which holds the blade. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. - Page 6 Straight line or orbital cutting action Conventional jig saws cut with a straight line action, that is, the blade moves only up and down in a straight line. ,Your saw also cuts in this manner but, for softer materials, an orbital cutting action can be selected.
- Page 7 Switch the tool on and lower the back end of the tool slowly, gradually allowing the balde to saw through the wood until the base is able to sit flat on the workpiece. You may then proceed for- ward with the cut in a normal manner.
- Page 8 Bevel cutting 1 . With the base tilted, you can make bevel cuts a t any angle between (left to right). Loosen the bolt on the back of the base with the hex wrench. Tilt the base to the desired angle. The edge of the hous- ing indicates the bevel angle.
- Page 9 Using guide rule (Rip fence) 1. When cutting widths (6") repeatedly, use will assure fast, clean, straight cuts. 2. To attach the guide rule (rip fence), use the hex wrench to loosen the screw on the under side of the base in front, slip in the guide rule and secure the screw.
- Page 10 When attaching the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence). Metal cutting Always use a suitable coolant (cutting oil) when cutting metal.
-
Page 11: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Center, always using Makita replacement parts. switched off and unplugged before attempting to perform... - Page 12 (packed 10 each in handy vinyl pouch) Jig saw blade Guide rule (Rip fence) Part No. 164113-2 Circular guide assembly Part 123030-5 with your Makita tool specified in this used only in the proper and intended manner. scro Hex wrench Part No. 783201-2...
- Page 13 @ " JIG SAW Model JV2000 Note: The switch, noise suppressor and other part configurations may differ from country to country...
- Page 14 MODEL J V 2 0 0 0 DESCRIPTION MACHINE Head Screw M 5 x 8 IWifh Warherl Compresslo" s p m g 4 Sleel Ball 4 PI" 4 Roller R e l a l M l s p o n g e 1 2 Blade Clamp Hex Socket Head Boll M 4 x 1 0 Plate...
- Page 15 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.