Table of Contents
Advertisement
CLASS 2 WIRING
3-PIN XLR:
2
• PIN 2 = (+), • PIN 3 = (–),
• PIN 1 = CHASSIS (SHIELD)
-10 dBV
1/4" PHONE, BALANCED:
+4 dBu
• TIP = (+), • RING = (–),
• SLEEVE = CHASSIS (SHIELD)
1/4" PHONE, UNBALANCED:
• SEE THE RANENOTE: SOUND
SYSTEM INTERCONNECTION
INPUTS 1 and 2: Choose between the balanced XLR or the balanced/unbalanced ¼" TRS jacks, but only use one. Inserting a ¼"
TS jack will work—however—we recommend using balanced lines, especially when connecting any cable over 10 feet (3 meters)
in length. Consult the Sound System Interconnection RaneNote provided with this manual.
INPUTS 1 and 2 Gain Trim Switch: In its +4 dBu position, the Input gain of the respective channel is unity. In the -10 dBV posi-
tion, the input gain is increased by 12 dB (although mathematically suspicious, it really is 12 dB, not 14 dB) to compensate for
certain recording devices. This switch must be in the +4 dBu position for front panel calibration accuracy.
OUTPUTS 1 and 2 are delivered by the balanced XLR or the unbalanced ¼" TS jacks. Using both types of Outputs are permissible
to drive two devices, such as an amplifier and a recorder. This device uses low impedance balanced line drivers. Do not connect the
XLR "+" or "–" output pins to ground, as this may cause the power supply to shut down. For unbalanced use, leave the unused output pin
("+" or "–") unterminated.
HIGH OUT
LOW OUT
CH 2 IN
AC22S
100-240 V
COMMERCIAL AUDIO
MADE IN U.S.A.
50/60 Hz 7 WATTS
EQUIPMENT 24TJ
RANE CORP.
R
MONO SUB: OMIT
HIGH OUT
MID OUT
OMIT MONO
AC22S STEREO 2-WAY CROSSOVER
100-240 V
ME15S
CHANNEL 2
50/60 Hz 7 WATTS
MADE IN U.S.A.
OUTPUT
INPUT
COMMERCIAL AUDIO
RANE CORP.
EQUIPMENT 24TJ
R
ME15S STEREO EQUALIZER
DC22S
WIRING
3-PIN XLR:
COMMERCIAL AUDIO
MADE IN U.S.A.
EQUIPMENT 24TJ
RANE CORP.
• PIN 2 = (+), • PIN 3 = (–),
• PIN 1 = CHASSIS (SHIELD)
1/4" PHONE, BALANCED:
R
• TIP = (+), • RING = (–),
• SLEEVE = CHASSIS (SHIELD)
1/4" PHONE, UNBALANCED:
100-240 V
• SEE THE RANENOTE: SOUND
50/60 Hz 7 WATTS
SYSTEM INTERCONNECTION
BALANCED
DC22S STEREO COMPRESSOR
TTM 56S
MADE IN U.S.A.
RANE CORP.
U.S. PATENT 6,813,361
TTM56S MIXER
100-240V
50/60 Hz
20 WATTS
STEREO 2-WAY
HIGH OUT
LOW OUT
CH 1 IN
SUBWOOFER SWITCH MUST
PIN 2: POSITIVE
BE SET TO 2- CHANNEL
PIN 3: NEGATIVE
FOR MONO 3-WAY
PIN 1: CHASSIS GND
MODE
SUBWOOFER
2-CHANNEL
MONO SUB
MONO SUB OUT
MONO
MONO 3-WAY
OMIT MONO
LOW OUT
3-WAY IN
WIRING
CHANNEL 1
OUTPUT
INPUT
TIP / PIN 2 = POSITIVE
RING / PIN 3 = NEGATIVE
SLEEVE = SIGNAL GROUND
PIN 1 = CHASSIS GROUND
OUTPUT
INPUT
OUTPUT
INPUT
2
2
1
1
-10 dBV
+4 dBu
BAL/UNBAL
BALANCED
BAL/UNBAL
BALANCED
BAL/UNBAL
BALANCED
BAL/UNBAL
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PHONO
MASTER
MIC
GROUNDS
FlexFX
OUTPUTS
BALANCED
AUX
PGM 2
PGM 1
L
L
OUT
IN
4
3
2
1
L
L
L
L
RETURN
SEND
PHONO
EFFECTS
4 3 2 1
R
R
R
R
R
R
OUT
IN
4
3
2
1
BALANCED
UNBALANCED
4
3
2
1
TIP = SEND
LINE
RING = RTN
System wiring example for a DJ system
OUTPUT
1
BALANCED
BAL/UNBAL
STEREO AMP, HIGH
-10 dBV
+4 dBu
MONO OR BRIDGED AMP, MONO SUB
Rear Panel Description
BALANCED
OUTPUTS
INPUTS
LEFT
RIGHT
LEFT
RIGHT
0
10
0
10
LEVEL
LEVEL
OUTPUTS
INPUTS
LEFT
RIGHT
LEFT
RIGHT
0
10
0
10
LEVEL
LEVEL
INPUT
1
-10 dBV
+4 dBu
BAL/UNBAL
RIGHT SPEAKER
LEFT SPEAKER
MONO SUBWOOFER
Manual-3
Advertisement
Table of Contents
