Table of Contents
Advertisement
Available languages
Available languages
iMPORTANT SAFETY
iNSTRUCTiONS
ifthe information in this manual is not followed
exactly, a fire or electrical shock may result causing property
damage, personal injury or death.
T_
Over Hazard
® A child or adult can tip the
range and be killed,
• Verify the anti-tip
device has
been installed to floor or wall.
= Ensure the anti-tip
device
is re-engaged
to floor
or wall when the range is moved.
= Do not operate
the range without
the anti-tip
device in place and engaged.
= Failure to follow
these instructions
can result in
death or serious
burns to children and adults.
Range
leg
_:_]1"_
leveling
\_
_)/_L_Anti-tip
_m_f
bracket
To check if the anti-tip bracket is installed properly, use
both arms to grasp the rear edge of the range back.
Carefully attempt to tilt range forward. When properly
installed, the range should not tilt forward.
Refer to the anti-tip bracket installation instructions
supplied with your range for proper installation.
Important
Notes to the Installer
1.
Read all instructions
contained
in these installation
instructions before installing range.
2.
Remove all packing material from the oven compartments
before connecting the gas and electrical supply to the
range.
3.
Observe all governing codes and ordinances.
4.
Be sure to leave these instructions with the consumer.
important
Note to the Consumer
Keep these instructions with your owner's guide for future
reference.
•
As when using any appliance generating heat, there are
certain safety precautions you should follow. These are
listed in the Use & Care Manual, read it carefully.
•
Be sure your range is installed and grounded properly
by a qualified installer or service technician.
•
Make sure the wall coverings
around the range can
withstand the heat generated by the range.
•
To eliminate the need to reach over the surface elements,
cabinet storage space above the elements should be
avoided.
2
Before Starting
Tools
You
May
Need
For leveling
legs and Anti-Tip Bracket:
•
Adjustable wrench or channel lock pliers
•
5/16" (21 mm) Nutdriver or Flat Head Screwdriver
•
Electric Drill & 1/8" (3 mm) Diameter Drill Bit (Masonry
Drill Bit if installing in concrete)
For electrical
supply connection:
•
1/4" (6 mm) & 3/8" (10 mm) Socket driver or Nutdriver
Additional
Materials
You May Need
•
Copper Electrical Wiring & Metal Conduit (for hard wiring)
Normal installation
Steps
1. Anti=Tip Bracket Installation
instructions
important
Safety Warning
To reduce the risk of tipping of the range, the range should
be secured to the floor by properly installed anti=tip bracket
and screws packed with the range. Failure to install the
anti=tip bracket will allow the range to tip over if excessive
weight is placed on an open door or if a child climbs upon
it. Serious injury might result from spilled hot liquids or from
the range itself.
If range is ever moved to a different location, the anti=tip
brackets must also be moved and installed with the range.
Instructions are provided for installation in wood or cement
fastened to either the floor or wall.
When installed to the
wall, make sure that screws completely penetrate dry wall
and are secured in wood or metal.
When fastening to the
floor or wall, be sure that screws do not penetrate electrical
wiring or plumbing.
A=
Locate the Bracket Using the Template- (Bracket may
be located on either the left or right side of the range. Use
the information below to locate the bracket if template is
not available).
Mark the floor or wall where left or right
side of the range will be located. If rear of range is against
the wall or no further than 1-1/4" (32 mm) from wall when
installed, you may use the wall or floor mount method. If
molding is installed and does not allow the bracket to fit
flush against the wall, remove molding or mount bracket
to the floor. For wall mount, locate the bracket by placing
the back edge of the template against the rear wall and
the side edge of template on the mark made referencing
the side of the range. Place bracket on top of template
and mark location of the screw holes in wall.
If rear of
range is further than 1-1/4" (32 mm) from the wall when
installed, attach bracket to the floor.
For floor mount,
locate the bracket by placing back edge of the template
where the rear of the range will be located.
Mark the
Advertisement
Table of Contents
