General information General information SCAN COIN AB reserves the right to revise and improve its products as it sees fit. This publication describes this product at the time of publication and may not reflect the product at all times in the future.
Make sure you disconnect the power cord before cleaning or servicing the machine. WARNING! Risk of jamming! This machine contains moving parts and sharp edges. Always be careful. Do not touch the components inside the machine while it is running. SC 1500 - Doc. No. 018522-000/03-025...
7. Throughout this guide, the instructions given apply to all versions unless stated otherwise. SC 1500 is light, easy to carry and easy to operate. By pressing keys on the control panel, you can select the machine’s various modes of operation.
• The nine pin standard RS-232 serial interface is used for communication with computer. • The five pin port is used for connecting the remote display RD 7 (accessory). Accessories Description RD 7 External display. 013617-000 013975-000 Communication cable. SC 1500 - Doc. No. 018522-000/03-025...
Caution! The machine must be protected by a fuse or a circuit breaker in the electrical circuit. The machine must be installed by a authorized SCAN COIN representative. Please also note the following when installing the machine: • Operating temperature 15–35 °C...
(density). If extremely dark and light notes are mixed in a bundle, the IP-function can be disabled and a manually selected level can be used, see “Setting note density (IP)” on page SC 1500 - Doc. No. 018522-000/03-025...
Page 12
(DD-function, short side)” on page 12). The factory setting is 4 mm. Manual start (SC 1500 std only). This function can be used together with other functions. When the MN-function is enabled, the machine does not start automatically when notes are placed on the feed table.
Page 13
When a suspicious note/document is detected, the machine stops at once with a beep tone and “CF4” appears on the display. Note! Cannot be used on all notes. The factory setting is for Euro-notes. SC 1500 - Doc. No. 018522-000/03-025...
Page 14
When a suspicious note/document is detected, the machine stops at once with a beep tone and “CF3” appears on the display. Note! Cannot be used on all notes. The factory setting is for Euro-notes. SC 1500 - Doc. No. 018522-000/03-025...
Press C to clear the batch number and disable batch counting mode (default mode). Place the notes on the feed table. Adjust the guides so that they fit the size of the notes. The counting starts automatically. SC 1500 - Doc. No. 018522-000/03-025...
Press DD Press SET several times until “dd” appears on the display. Press numerical key 1 (increase) or 0 (decrease) to select the desired detecting accuracy. The range is 2-7 mm. Press ST/CL. SC 1500 - Doc. No. 018522-000/03-025...
Press numerical key 1 (increase) or 0 (decrease) to select proper density level: – DE 1-2: thin, light colored or new note/document; – DE 3-5: note/document with color between light and dark; – DE 6-8: thick, dark colored, old or dirty note/document. Press ST/CL. SC 1500 - Doc. No. 018522-000/03-025...
Press numerical key 1 or 0 to select the desired medium speed. Press SET. “SP3” appears on the batch display. Press numerical key 1 or 0 to select the desired low speed. Press ST/CL. SC 1500 - Doc. No. 018522-000/03-025...
“dbL”. Turn the adjusting knob slightly counter-clockwise to decrease the gap between the feed rollers. • If the notes run hard or too slow, turn the adjusting knob clockwise to increase the gap between the rollers. SC 1500 - Doc. No. 018522-000/03-025...
The suspicious note is not included in the counted total. Suspicious note/document detected (IR). Remove the suspicious note only and then press ST/CL to continue counting. The suspicious note is not included in the counted total. SC 1500 - Doc. No. 018522-000/03-025...
Page 22
Error position Left count sensor Right count sensor Left double sensor Right double sensor Stacker sensor Feed sensor Speed sensor 1 Feed sensor 2 Stacker sensor 3 Left count sensor 4 Right count sensor SC 1500 - Doc. No. 018522-000/03-025...
Make sure the note holders are not in ther outermost position. Place the handle in its front position. Lift the upper friction roller unit. Inspect and if necessary clean the area with a soft brush. SC 1500 - Doc. No. 018522-000/03-025...