TP-Link TL-SG2216 Installation Manual
Hide thumbs
Also See for TL-SG2216:
- Reference manual (226 pages) ,
- User manual (132 pages) ,
- Cli reference manual (120 pages)
Related Manuals for TP-Link TL-SG2216
Summary of Contents for TP-Link TL-SG2216
- Page 1 Business Networking Solution Installation Guide Gigabit Smart Switch TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452...
-
Page 2: Fcc Statement
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. - Page 3 Network Administrator Conventions Due to the similarity in structure of the Gigabit Smart Switch series, in this Installation Guide we take TL-SG2216 as an example to illustrate Chapter 2 Installation, Chapter 3 Lightning Protection, Chapter 4 Connection and Chapter 5 Configuration.
-
Page 4: Table Of Contents
Contents Chapter 1 Introduction ———————————— 01 Product Overview ........01 Appearance ........... 0 Chapter 2 Installation ———————————— 07 Package Contents ........07 Safety Precautions ........07 Installation Tools ........09 Product Installation ........10 Chapter 3 Lightning Protection ———————— 12 Cabling Reasonably ........12 Connect to Ground ........14 Equipotential Bonding .......15 Use Lightning Arrester ......16 Chapter 4 Connection ————————————... -
Page 5: Chapter 1 Introduction
IP telephones, wireless LAN access points, network cameras, network hubs, embedded computers etc. Appearance Front Panel ■ The front panel of TL-SG2216 is shown as the following figure. LEDs Reset 10/100/1000Mbps RJ45 Port SFP Port Figure 1-1 Front Panel of TL-SG2216... - Page 6 1000Mbps. Each has a corresponding Link/Act LED and a 1000Mbps LED. SFP Port Designed to install the SFP module. TL-SG2216/TL-SG2424 switch features 2/4 SFP transceiver slots that are shared with the associated RJ45 ports. The associated two ports are referred as a “Combo” port, which means they cannot be used simultaneously, otherwise only SFP port works.
- Page 7 Gigabit Smart Switch The front panel of TL-SG2424P is shown as the following figure. LEDs LED Mode Switch Button Reset 10/100/1000Mbps RJ45 Port SFP Port Figure 1-3 Front Panel of TL-SG2424P LEDs TL-SG2424P has an LED mode switch button which is for switching the LED status indication.
- Page 8 Gigabit Smart Switch Status Indication The remaining PoE power≤7W The remaining PoE power keeps ≤7W after this LED is PoE Max Flashing on for 2 minutes The remaining PoE power≥7W The port is supplying power normally Green The supply power exceeds the correponding port's Flashing 10/100/ maximum power...
-
Page 9: Rear Panel
TL-SG2424P TL-SG2452 Note: For TL-SG2216/TL-SG2424/TL-SG2424P, when using the SFP port with a 100M module or a gigabit module, you need to log on to the GUI (Graphical User Interface) of the switch and configure its corresponding Speed and Duplex mode on Switching→Port→Port Config page. - Page 10 Gigabit Smart Switch Grounding Terminal The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed information, please refer to Chapter 3 Lightning Protection. Power Socket Connect the female connector of the power cord here, and the male connector to the AC (Alternating Current) power outlet.
-
Page 11: Chapter 2 Installation
Gigabit Smart Switch Chapter 2 Installation Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. This Installation Guide One Switch One Power Cord Two mounting brackets and the One Resource CD fittings 2.2 Safety Precautions... -
Page 12: Site Requirements
Gigabit Smart Switch Site Requirements ■ Temperature/Humidity Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. -
Page 13: Installation Tools
Gigabit Smart Switch Lightning Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. -
Page 14: Product Installation
Gigabit Smart Switch 2.4 Product Installation Desktop Installation ■ To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. - Page 15 Gigabit Smart Switch Rack Figure 2-3 Rack Installation Caution: Please set 5~10cm gaps around the device for air circulation. ■ Please avoid any heavy thing placed on the device. ■ Please mount devices in sequence from the bottom to top of the rack and ensure a ■...
-
Page 16: Chapter 3 Lightning Protection
Gigabit Smart Switch Chapter 3 Lightning Protection Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. - Page 17 Gigabit Smart Switch Requirements for Cabling Indoors ■ When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. The main cable should be paved in the metal raceway of the access shaft. When ■...
-
Page 18: Connect To Ground
Gigabit Smart Switch Min Parallel Cable Pave Way Length (mm) Parallel cabling 2~5kVA One is in the grounded metal raceway or metal pipe powerline The both are in the grounded metal raceway or metal pipe Parallel cabling >5kVA One is in the grounded metal raceway or metal pipe powerline The both are in the grounded metal raceway or metal pipe... -
Page 19: Equipotential Bonding
Gigabit Smart Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. Connecting to the Ground via the Power Supply ■ If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth) cable of the AC power supply as shown in the following figure. -
Page 20: Use Lightning Arrester
Gigabit Smart Switch Grounding Terminal Equipotential Bonding Cable Figure 3-3 Equipotential Bonding Ground Cable Grounding Bar When equipotential bonding, please note that the cable should be copper wrapped Kelly with its area being 6mm at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point. - Page 21 Gigabit Smart Switch The port rate of the signal lightning arrester should match the rate of the desired ■ port on the device. If it is not matched, this signal lighting arrester will not work. Purchase a standard lightning arrester. Install signal lightning arrester near the protected device and connect it to the ■...
-
Page 22: Chapter 4 Connection
Gigabit Smart Switch Chapter 4 Connection Ethernet Port Connect a Ethernet port of the switch to the computer by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable Figure 4-1 Connecting the RJ45 Port 4.2 SFP Port Connect the SFP port to a SFP module. If an SFP transceiver (purchased separately) is installed in a slot and has a valid link on the port, the associated RJ45 port will be disabled and cannot be used. -
Page 23: Verify Installation
Gigabit Smart Switch 4.3 Verify Installation After completing the installation, please verify the following items: There are 5~10cm of clearance around the sides of the device for ventilation and ■ the air flow is adequate. The voltage of the power supply meets the requirement of the input voltage of the device. ■... -
Page 24: Chapter 5 Configuration
Gigabit Smart Switch Chapter 5 Configuration Configure the Switch via GUI 1. To access the GUI of the switch, open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key. Figure 5-1 Web Browser Note: To log on to the GUI of the switch, the IP address of your PC should be set in the same subnet addresses of the switch. -
Page 25: Configure The Switch Using Cli
Gigabit Smart Switch Figure 5-3 Main Page of the Switch 5.2 Configure the Switch Using CLI You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the following steps: 1. - Page 26 Gigabit Smart Switch 3. Type cmd in the prompt Run window as Figure 5-5 and click OK. Figure 5-5 Run Window 4. Type telnet 192.168.0.1 in the command prompt shown as Figure 5-6, and press the Enter button. Figure 5-6 Connecting to the Switch Configuration...
-
Page 27: Appendix A Troubleshooting
Gigabit Smart Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the Switch? Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin. -
Page 28: Appendix B Hardware Specifications
1000Base-T: 4-pair UTP/STP of Cat. 5, Cat. 5e and Cat. 6 or above (maximum 100m) 1000Base-X: MMF or SMF SFP Module (Optional) LEDs TL-SG2216/TL-SG2424: Power, System, 1000Mbps, Link/Act TL-SG2424P: Power, System, Speed, Port Status LED, PoE, PoE TL-SG2452: PWR,SYS,10/100/1000Mbps Operating Temperature 0℃~40℃... -
Page 29: Appendix C Technical Support
Gigabit Smart Switch Appendix C Technical Support For more troubleshooting help, please go to: www.tp-link.com/support/faq ■ To download the latest Firmware, Driver, Utility and User Guide, go to: ■ www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: ■... - Page 30 Gigabit Smart Switch Russian Federation Tel: 8 (499) 754 5560 (Moscow NO.) 8 (800) 250 5560 (Toll-free within RF) E-mail: support.ru@tp-link.com Service time: From 09:00 to 21:00 (Moscow time) *Except weekends and holidays in RF Singapore Tel: +65 6284 0493 Fee: Depending on rate of different carriers.
- Page 32 Website: http://www.tp-link.com E-mail: support@tp-link.com 7106504834 Rev2.0.0...