Page 1: Quick Reference
TACOMA CUSTOMER EXPERIENCE CENTER 2 0 1 1 1-800-331-4331 QUICK REFERENCE GUIDE Printed in U.S.A. 6/10 Cert no. SGSNA-COC-005612 I n f o r ma t i o n P r o v i d e d b y : 10-TCS-03988 00505-QRG11-TAC...
Page 2 -under the rear seat Tool bag of your vehicle’s capabilities and limitations. Jack Your dealership and the entire staff of Toyota Motor Sales, U.S.A., Inc. wish you many years of satisfied driving in your new Tacoma. Removing the spare tire...
Page 3: Table Of Contents
INDEX Engine maintenance OVERVIEW Fuel tank door and cap Hood release Indicator symbols Instrument cluster Instrument panel Keyless entry Accessory meter FEATURES/OPERATIONS Air Conditioning/Heating Audio 14-15 Automatic Transmission Clock Cruise control Four-wheel drive Lights & turn signals Light control-Instrument panel Parking brake Power outlets Rear differential lock...
Page 4 OVERVIEW Instrument panel Steering wheel controls (if equipped) Volume control buttons (for audio) “ ” buttons (for audio) “MODE” button (for audio) Front fog light switch Rear differential lock switch 115V AC Power outlet ON/OFF switch Instrument panel light control Headlight and turn signal controls Windshield wiper and washer controls Two-wheel/Four-wheel drive selector...
Page 5 Parking brake lever Front passenger airbag manual ON/OFF switch Air Conditioning controls 12V DC Power outlet Emergency flasher button Cigarette lighter Parking brake lever Cruise control Ignition switch Parking brake pedal “RSCA OFF” (Roll Sensing Curtain shield Airbags OFF) switch “DAC”...
Page 6: Instrument Cluster
Engine oil replacement reminder If indicator does not turn off within a few seconds of starting engine, there may be a malfunction. Have vehicle inspected by your Toyota dealer. If this light flashes, refer to “SRS airbag,” Section 1-7-, 2011 Owner’s Manual.
Page 7 Open door warning Airbag SRS warning Automatic Transmission fluid temperature warning Low Tire Pressure Warning Theft deterrent/Engine immobilizer system indicator Roll Sensing Curtain shield Airbags OFF indicator Headlight low beam indicator Headlight high beam indicator Turn signal indicator Automatic Transmission indicator (5-speed)/(4-speed) Four-wheel drive indicator Low speed four-wheel drive indicator Rear differential lock indicator...
Page 8: Fuel Tank Door And Cap
OVERVIEW Keyless entry (if equipped) Locking operation Unlocking operation Push ONCE: Driver door TWICE: All doors NOTE: If a door is not opened within 30 seconds of unlocking, all doors will Push relock for safety. Panic button Push and hold Fuel tank door and cap Turn to open Pull...
Page 9: Engine Maintenance
Engine maintenance 4 cylinder (2TR-FE) engine 6 cylinder (1GR-FE) engine Windshield washer fluid tank Engine coolant reservoir Engine oil filler cap Power steering fluid reservoir Engine oil level dipstick NOTE: Regularly scheduled maintenance, including oil changes, will help extend the life of your vehicle and maintain performance. Please refer to the “Warranty Maintenance Guide.”...
Page 10: Automatic Transmission
FEATURES/OPERATIONS Automatic Transmission (if equipped) 5-speed models Park Park* Reverse Reverse Neutral Neutral Drive Drive Fourth gear Fourth gear Third gear Third gear Second gear Second gear First gear First gear 4-speed models Park* Reverse Neutral Drive Third gear Second gear First gear * The engine switch must be “ON”...
Page 11: Clock
Four-wheel drive (if equipped) Turn Turn Push and turn High speed (2WD) High speed (4WD) Shift when speed is below 62 mph. Low speed (4WD) Shift into neutral while stopped, or depress clutch pedal at speeds below 2 mph. For best fuel economy and performance under normal driving conditions, keep in “H2”...
Page 12: Parking Brake
FEATURES/OPERATIONS Parking brake Automatic Transmission Set: Depress Release: Depress again Manual Transmission Release (1) Push button (2) Turn and push in lever Seats-Head restraints Separate seats-Front Bench seat-Front Lock release button Lock release button Seat adjustments-Front Separate seat Bench seat Seat position (forward/backward) Driver’s seat lumbar support (if equipped) Seatback angle...
Page 13: Seats-Folding Rear
Seats-Folding rear Access cab (1) Stow the seat belt buckles. (2) Raise the bottom cushion up while pulling the lever until it locks. Double cab (1) Stow the seat belt buckles. (2) Pass the seat belt through the seat belt hangers. (3) Remove the head restraint and swing the bottom cushion.
Page 14: Lights & Turn Signals
FEATURES/OPERATIONS Lights & turn signals Headlights Low beam High beam flasher Headlights Parking lights High beam -Daytime Running Light system (if equipped) Automatically turns on the front turn signal lights at a reduced intensity. -Automatic light cutoff system Automatically turns lights off when driver’s door is opened with the engine switch in the “ACC”...
Page 15: Cruise Control
Windshield wipers & washers With intermittent wiper Single wipe Adjust frequency* * Intermittent windshield Interval wipe wiper frequency adjustment Slow Pull to wash and wipe Rotate to increase/decrease wipe frequency. Fast Without intermittent wiper Single wipe Slow Fast Pull to wash and wipe Cruise control (if equipped) Turning system ON/OFF System ON/OFF...
Page 16 FEATURES/OPERATIONS Audio Type 1 Preset buttons - functions in other modes indicated below number Eject CD Push to turn Push to adjust ON/OFF tone & balance Seek station/ View text Search playback Push to skip up/down folder Seek station/ and radio CD track select category type Mode...
Page 17: Accessory Meter
Steering wheel switches (if equipped) Volume control “ ” Use to search within the selected audio medium (radio, CD, iPod, etc.). “MODE” Push to turn audio ON and select an audio mode. Push and hold to turn the audio system OFF. AUX audio jack Push “DISC AUX”...
Page 18: Air Conditioning/Heating
FEATURES/OPERATIONS Air Conditioning/Heating Fan speed Temperature selector Airflow vent In “ ” or “ ” mode, use fresh air (“ ” indicator OFF) to reduce window fogging. Recirculate cabin air (fresh air when OFF) Air Conditioning ON/OFF (if equipped) Use fresh air to quickly cool interior, then change to recirculate for cooler air.
Page 19: Power Outlets
Power outlets 12V DC Key must be in the “ACC” or “ON” position to be used. 115V AC (if equipped) Green light Right side of bed ON/OFF switch Push Yellow light The engine must be running for use. Yellow Light Only Max Capacity 115V AC/100W Green &...
Page 20: Telephone Controls (Bluetooth ® )
Refer to “Using the hands-free phone system (for cellular phone),” Section 3-3 in the Owner’s Manual for more details, or go to Toyota.com and enter “Bluetooth” in the keyword search. I n f o r ma t i o n P r o v i d e d b y :...
Page 21: Door Locks-Power
SAFETY AND EMERGENCY FEATURES Seat belts Take up slack Too high Keep as low on hips as possible If belt is fully extended, then retracted even slightly, it cannot be re-extended beyond that point, unless fully retracted again. This feature is used to help hold child restraint systems securely.
Page 22: Doors-Child Safety Locks
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation specifications. If the tire pressure indicator flashes for more than 60 seconds and then remains on, take the vehicle to your local Toyota dealer. Doors-Child safety locks (double cab only) Rear door Moving the lever to “LOCK”...
Page 23 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Two Wheel Drive Four Wheel Drive Anti-Lock Brake System Accessory Automatic Locking Retractor A-TRAC Active Traction Control AUTO LSD Automatic Limited Slip Differential Child Restraint System Downhill assist control Electronic Control Unit Event Data Recorder Emergency Locking Retractor GAWR Gross Axle Weight Rating...
Page 24 ABBREVIATIONS MEANING TPMS Tire Pressure Warning System TRAC Traction Control Treadwear indicators Vehicle Identification Number Vehicle Stability Control I n f o r ma t i o n P r o v i d e d b y :...
Page 25: For Your Information
Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 26 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 27 CAUTION General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 28 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 29 I n f o r ma t i o n P r o v i d e d b y :...
Page 30: Before Driving
TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior and Air conditioning and audio systems, as well as other in- exterior features terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 31 Pictorial index Exterior Regular Cab models Windshield wipers P. 168 Outside rear view mirrors P. 68 Hood P. 370 Parking and front side marker lights P. 165 Headlights P. 165 Front turn signal lights and daytime ∗ P. 153, 166 running lights I n f o r ma t i o n P r o v i d e d b y :...
Page 32 ∗ Back window P. 73 Rear turn signal lights P. 153 Fuel filler door P. 74 Stop/tail lights P. 165 Side doors P. 35 Tailgate P. 40 License plate lights P. 165 Tires Rotation P. 388 Replacement P. 450 Rear side marker lights P.
Page 33 Pictorial index Exterior Access Cab models Windshield wipers P. 168 Outside rear view mirrors P. 68 Hood P. 370 Parking and front side marker lights P. 165 Headlights P. 165 ∗ Fog lights P. 167 Front turn signal lights and daytime ∗...
Page 34 ∗ Rear turn signal Back window P. 73 lights P. 153 Fuel filler door P. 74 Stop/tail lights P. 165 Access doors P. 39 Side doors P. 35 Tailgate P. 40 License plate lights P. 165 Tires Rotation P. 388 Replacement P.
Page 35 Pictorial index Exterior Double Cab models Windshield wipers P. 168 Outside rear view mirrors P. 68 Hood P. 370 Parking and front side marker lights P. 165 Headlights P. 165 ∗ Fog lights P. 167 Front turn signal lights and daytime ∗...
Page 36 ∗ Back window P. 73 Rear turn signal Fuel filler door P. 74 lights P. 153 Side doors P. 35 Stop/tail lights P. 165 Tailgate P. 40 License plate lights P. 165 Rear side marker lights P. 165 Tires Rotation P.
Page 37 Pictorial index Interior ∗ Seat belts P. 58 Bottle holders P. 314 ∗ Front console box P. 311 Head restraints P. 54 Horn P. 156 SRS driver airbag P. 82 SRS front passenger airbag P. 82 ∗ Glove box P. 311 Rear seats P.
Page 38 ∗ Accessory meter P. 164 ∗ Outside temperature display P. 322 ∗ Compass P. 347 ∗ Garage door opener box P. 343 ∗ Personal lights P. 309 ∗ Overhead console P. 318 Interior light P. 309 SRS curtain shield airbags P.
Page 39 Pictorial index Interior ∗ Door lock switch P. 36 Inside door lock button P. 36 ∗ Power window switches P. 71 ∗ Window lock switch P. 71 I n f o r ma t i o n P r o v i d e d b y :...
Page 40 Bench type front seat Shift lever P. 147, 150 Cup holders P. 312 ∗ Shift lock override button P. 469 Separated type front seats with an automatic transmission Shift lever P. 147 Cup holders P. 312 Cup holders P. 312 Shift lock override button P.
Page 41 Pictorial index Interior Separated type front seats with a manual transmission Shift lever P. 150 Cup holders P. 312 I n f o r ma t i o n P r o v i d e d b y :...
Page 42 Access Cab models ∗ Sub woofer P. 270 Back window ∗ lock release lever P. 73 Auxiliary boxes P. 316 Rear console box P. 311 ∗ : If equipped I n f o r ma t i o n P r o v i d e d b y :...
Page 43 Pictorial index Interior Double Cab models Grocery bag hooks P. 341 Back window lock ∗ Bottle holders P. 314 release lever P. 73 Flashlight holder P. 340 Storage boxes P. 339 ∗ Cargo net hooks P. 342 ∗ : If equipped ∗...
Page 44: Instrument Panel
Pictorial index Instrument panel Gauges and meters P. 157 Tilt and telescopic steering lock release lever P. 64 Tire pressure warning reset switch P. 388 Hood lock release lever P. 370 ∗ Parking brake pedal P. 154 Auxiliary box P. 316 Bottle holders P.
Page 45 Pictorial index Instrument panel Passenger airbag Audio system P. 244 ∗ off switch P. 95 Air conditioning system P. 236 Front-wheel drive ∗ Emergency flasher switch P. 430 control switch P. 178 ∗ A-TRAC switch P. 182 AUX port P. 271 Power outlet P.
Page 46 Windshield wipers and Engine (ignition) switch P. 144 washer switch P. 168 ∗ Parking brake lever P. 154 ∗ ∗ Audio remote control switches P. 273 Telephone switches P. 281 ∗ Talk switch P. 281 ∗ Cruise control switch P. 171 ∗...
Page 47 Pictorial index Instrument panel ∗ Fog light switch P. 167 ∗ RR DIFF LOCK switch P. 186 Instrument panel light control dial P. 158 Power outlet main ∗ switch P. 325 Headlight switch P. 165 Turn signal lever P. 153 ∗...
Page 48 Pictorial index Luggage compartment Deck rails P. 203 Tie-down cleats P. 337 ∗ Power outlet P. 325 Auxiliary boxes P. 335 Deck hooks P. 336 ∗ : If equipped ∗ : 4WD models only I n f o r ma t i o n P r o v i d e d b y :...
Page 49: Key Information
Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 470)
Page 50 1-1. Key information NOTICE To prevent key damage (vehicles with engine immobilizer system) Do not subject the keys to strong shocks, expose them to high tempera- tures by placing them in direct sunlight, or get them wet. Do not expose the keys to electromagnetic materials or attach any mate- rial that blocks electromagnetic waves to the key surface.
Page 51: Opening, Closing And Locking
1-2. Opening, closing and locking the doors ∗ Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
Page 52 Customization that can be configured at Toyota dealer Settings (e.g. wireless remote control system) can be changed. (Customizable features →P. 518)
Page 53 1-2. Opening, closing and locking the doors Certification for wireless remote control MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ4-34R IC (Canada) IDs: Transmitter: 1470A-1T Receiver: 1470A-6R MADE IN U.S.A. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Page 54: Side Doors
1-2. Opening, closing and locking the doors Side doors The vehicle can be locked/unlocked using the wireless remote con- trol, key or door lock switch. Wireless remote control (if equipped) →P. 32 Regular Cab models Locks the door Unlocks the door Access Cab and Double Cab models Locks all doors Unlocks all doors...
Page 55 1-2. Opening, closing and locking the doors Door lock switch (if equipped) Driver’s door lock switch Locks all doors Unlocks all doors Passenger’s door lock switch Locks all doors Unlocks all doors Inside door lock button Locks the door Unlocks the door Pulling the inside handle can open the front door even if the inside door lock button is in the...
Page 56 1-2. Opening, closing and locking the doors Locking the front doors from the outside without a key Move the inside door lock button to the lock position. Close the door. Vehicles with power door lock system The door cannot be locked if a front door is open and the key is in the engine switch.
Page 57 1-2. Opening, closing and locking the doors CAUTION To prevent an accident Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. Always use a seat belt.
Page 58: Access Doors (Access Cab Models Only)
1-2. Opening, closing and locking the doors Access doors (Access Cab models only) The access door (rear door) can be opened using the inside handle. Open the front door widely Pull (from the outside) or push (from the inside) the inside handle of the access door.
Page 59: Tailgate
1-2. Opening, closing and locking the doors Tailgate The tailgate can be opened. Pull the handle Open the tailgate slowly The support cables will hold the tailgate horizontal. After closing the tailgate, try pulling it toward you to make sure it is securely locked. Removing the tailgate Before removing the tailgate These connector covers are used when removing the tailgate, to...
Page 60 1-2. Opening, closing and locking the doors To disconnect the wire harness connectors ( ), press and hold the lock of the tailgate wire harness connector (White) and pull apart. Tailgate wire harness connec- tor (White) Frame wire harness connector (Gray) Attach connector...
Page 61 1-2. Opening, closing and locking the doors Pull out the wire harness from the vehicle bed. Attach connector cover (Gray) to the tailgate wire har- ness connector (White). Tailgate wire harness connec- tor (White) Connector cover (Gray) Removing the tailgate Open the tailgate to the angle where you can release the brackets on the support cables...
Page 62 1-2. Opening, closing and locking the doors Slide the tailgate a little to the right to unhook the left side. To attach the tailgate, follow the removal procedure in reverse order. Rear step bumper For rear end protection and eas- ier step-up loading.
Page 63 1-2. Opening, closing and locking the doors NOTICE To prevent damage to the tailgate wire harness Do not pull out all of the tailgate wire harness before open the tailgate. To prevent damage to the camera lens (vehicles with rear view monitor system) Store the removed tailgate with the back-up camera lens facing upward.
Page 64: Adjustable Components
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Bench type seat Seat position adjustment lever Separated type seats Seat position adjustment lever Driver’s seat lumbar sup- port adjustment knob (if equipped) Seatback angle adjustment lever I n f o r ma t i o n P r o v i d e d b y :...
Page 65 1-3. Adjustable components (seats, mirrors, steering wheel) Moving passenger’s seat for rear seat entry (if equipped) Lift the seatback angle adjusting lever or press the pedal behind the seatback. The seat will slide forward. Move the seat to the front-most position.
Page 66 1-3. Adjustable components (seats, mirrors, steering wheel) Folding passenger’s seat (vehicles with seatback table) Pull the seatback angle adjusting lever and raise the seatback to its upright position. Pull the seatback folding lever and fold the seatback down. I n f o r ma t i o n P r o v i d e d b y :...
Page 67 1-3. Adjustable components (seats, mirrors, steering wheel) Active head restraints (Access Cab and Double Cab models only) When occupant’s back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward to help reduce the risk of whiplash on the seat occupant.
Page 68 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat adjustment Be careful that the seat does not hit passengers or luggage. Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 69: Rear Seats (Access Cab And Double Cab Models)
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats (Access Cab and Double Cab models) Access Cab models The bottom cushion of the rear seats can be raised and lowered. Before raising the bottom cushion Stow the seat belt buckles. This prevents the seat belt buckles from falling out when you fold the seatback.
Page 70 1-3. Adjustable components (seats, mirrors, steering wheel) Double Cab models The seatback of the rear seat can be folded. Before folding rear seats Stow the rear seat belt buck- les. This prevents the seat belt buckles from falling out when you fold the seatback.
Page 71 1-3. Adjustable components (seats, mirrors, steering wheel) Attach the head restraints to the holders located on the back sides of the bottom cush- ions. Fold down the seatback by pulling the lock release strap. CAUTION When the seatback is folded/the bottom cushion is raised Do not sit on or place anything on the seatback or auxiliary box while driving.
Page 72 1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE Before folding the seats The seat belts buckles must be stowed. I n f o r ma t i o n P r o v i d e d b y :...
Page 73: Head Restraints
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Adjusting the head restraints Bench type front seat Pull the head restraints up. Down Push the head restraint down while pushing the lock release button.
Page 74 1-3. Adjustable components (seats, mirrors, steering wheel) When using the rear head restraints (Access Cab models only) To use Lift up the head restraint until it locks. To fold Pull the head restraint lock release lever to fold the head restraint.
Page 75 1-3. Adjustable components (seats, mirrors, steering wheel) Removing the rear head restraints (Double Cab models only) Pull the head restraint up while pushing the lock release button. Installing the front head restraints Bench type seat Align the head restraint with the installa- tion holes and push it down to the lock position.
Page 76 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. Adjusting the front center seat (Bench type seat) and rear center seat head restraints (Double Cab models) Always raise the head restraint one level from the stowed position when using.
Page 77: Seat Belts
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. Correct use of the seat belts l Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 78 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the belt (front seats) Move the height adjuster up as needed until you hear a click. Down Push the lock release button and slide the height adjuster down. Center seat belt of the bench seat Make sure the shoulder belt pass through the guide when using the center seat belt.
Page 79 1-3. Adjustable components (seats, mirrors, steering wheel) Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 80 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system.
Page 81 Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 82 Seat belt damage and wear Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.
Page 83: Steering Wheel
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and press the lever down. Adjust to the ideal position by moving the steering wheel horizontally and vertically. After adjustment, pull the lever up to secure the steering wheel.
Page 84: Anti-Glare Inside Rear View Mirror
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position I n f o r ma t i o n P r o v i d e d b y :...
Page 85 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode ON/ The indicator comes on when automatic mode is turned on.
Page 86 1-3. Adjustable components (seats, mirrors, steering wheel) To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them. CAUTION Caution while driving Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
Page 87: Outside Rear View Mirrors
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted. Power-adjustable type Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch. I n f o r ma t i o n P r o v i d e d b y :...
Page 88 1-3. Adjustable components (seats, mirrors, steering wheel) Manually adjustable type Adjust the mirror up, down, in or out by pushing the mirror surface. Folding back the mirrors Push backward to fold the mir- rors. Mirror operating conditions (vehicles with power-adjustable type only) The engine switch is in the ACC or ON position.
Page 89 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION When driving the vehicle Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. Do not adjust the mirrors while driving.
Page 90: Opening And Closing
1-4. Opening and closing the windows ∗ Power windows The power windows can be opened/closed using the following switches. Driver’s power window switches Closing Opening One-touch opening (driver’s window only) *: Pressing the switch in the opposite direction will stop win- dow travel partway.
Page 91 1-4. Opening and closing the windows The power windows can be operated when The engine switch is in the ON position. Operating the power windows after turning the engine switch off The power windows can be operated for approximately 43 seconds even after the engine switch is turned off.
Page 92: Back Window (Vehicles With Sliding Type)
1-4. Opening and closing the windows Back window (vehicles with sliding type) The back window can be opened and closed using the lock release lever. Open/close Push the lock release lever and slide the back window. Closing the back window Make sure that the back window is securely closed after closing it.
Page 93: Refueling Opening The Fuel Tank Cap
1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. Before refueling the vehicle Turn the engine switch off and ensure that all the doors and win- dows are closed. Opening the fuel tank cap Open the fuel filler door.
Page 94 1-5. Refueling Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. Fuel types Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] or higher) Fuel tank capacity Approximately 21.1 gal.
Page 95 This may cause static electricity to build up, resulting in a possible engine hazard. When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 96 1-5. Refueling NOTICE Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface. To prevent damage to the fuel filler door Do not apply excessive force.
Page 97: Theft Deterrent System
1-6. Theft deterrent system ∗ Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the key has been removed from the engine switch to indi-...
Page 98 1-6. Theft deterrent system Certifications for the engine immobilizer system For vehicles sold in U.S.A. FCC ID: MOZRI-21BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 99: Safety Information
1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 45) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 100 1-7. Safety information CAUTION While driving Do not adjust the position of the driver’s seat while driving. Doing so could cause the driver to lose control of the vehicle. Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 101: Srs Airbags
1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and right front...
Page 102 1-7. Safety information Airbag system components Vehicles with bench type front seat Vehicles with separated type front seat I n f o r ma t i o n P r o v i d e d b y :...
Page 103 1-7. Safety information Front passenger airbag Driver’s seat position sen- Curtain shield airbags Driver’s seat belt buckle Side airbags switch AIR BAG ON and AIR BAG Front passenger’s seat belt OFF indicator lights buckle switch warning light Occupant detection system RSCA OFF indicator light (ECU and sensors) Driver airbag...
Page 104 1-7. Safety information In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. A chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants. SRS warning light This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensor assemblies, curtain shield air-...
Page 105 1-7. Safety information It is possible that in some collisions where the forward deceleration of the vehicle is very close to the designed threshold level, the SRS front air- bags and the seat belt pretensioners may not activate together. The SRS front passenger airbag will not activate if there is no passenger sitting in the front passenger seat.
Page 106 1-7. Safety information The SRS curtain shield airbags may also deploy under the situation shown in the illustration. The angle of vehicle tip-up is marginal. The vehicle skids and hits a curb stone. Types of collisions that may not deploy the SRS airbag (front airbags) The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision.
Page 107 1-7. Safety information Types of collisions that may not deploy the SRS airbag (side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
Page 108 1-7. Safety information When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. Any of the SRS airbags have been inflated. The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS airbags to inflate.
Page 109 1-7. Safety information CAUTION SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts. The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag.
Page 110 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children.
Page 111 1-7. Safety information CAUTION SRS airbag precautions Do not sit on the edge of the seat or lean against the dashboard. Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. Do not drive the vehicle while the driver or passenger has items resting on their knees.
Page 112 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 113 Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
Page 114 1-7. Safety information Passenger airbag off switch (Access Cab models) The passenger airbag off switch is designed to disable the front pas- senger airbag in order to allow usage, if necessary, of the front pas- senger seat by a member of a passenger risk group identified in TABLE 1 is occupying the front passenger seating position (→P.
Page 115 1-7. Safety information Passenger risk group TABLE 1: A PASSENGER RISK GROUP Infant. An infant (less than 1 year old) who must ride in the front seat because: • Vehicle has no rear seat; • Vehicle has a rear seat too small to accommodate a rear-facing infant seat;...
Page 116 1-7. Safety information CAUTION When the passenger airbag off switch is turned off Do not turn the passenger airbag off switch to the OFF position except when a member of a passenger risk group identified in TABLE 1 is occupy- ing the front passenger seating position.
Page 117 1-7. Safety information CAUTION For normal driving Make sure the RSCA OFF indicator is not turned on. If it is left on, the curtain shield airbag will not activate in the event of an accident, which may result in death or serious injury. I n f o r ma t i o n P r o v i d e d b y :...
Page 118: Front Passenger Occupant Classification System
1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the right front passenger seat and activates or deactivates the devices for the front passenger.
Page 119 1-7. Safety information Conditions and operation of the front passenger occupant classification system Regular Cab and Double Cab models l Indicator/warning light Condition detected AIR BAG ON Front passen- by the front passen- and AIR BAG SRS warning ger’s seat belt ger occupant clas- OFF indicator light...
Page 120 1-7. Safety information : The right front passenger on the bench seat. : The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture.
Page 121 1-7. Safety information Access Cab models l Indicator/warning light AIR BAG Front pas- Condition detected Passen- ON and senger’s by the front passen- ger airbag AIR BAG warning seat belt ger occupant clas- off switch reminder OFF indi- light sification system position light cator lights...
Page 122 1-7. Safety information l Devices Condition Curtain detected by Passen- Side air- Front shield air- Front pas- the front pas- ger air- bag on passen- bag in the senger’s senger occu- bag off the front front pas- seat belt ger air- pant switch passen-...
Page 123 1-7. Safety information : In case the indicator is not illuminated, consult this manual for installing the child restraint system properly. (→P. 111) CAUTION Front passenger occupant classification system precautions Observe the following precautions regarding front passenger occupant clas- sification system. Failure to do so may cause death or serious injury.
Page 124 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 125: Child Restraint Systems
1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Page 126 1-7. Safety information Forward facing — Convertible seat Booster seat Selecting an appropriate child restraint system Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt. If a child is too large for a child restraint system, sit the child on a rear seat and use the vehicle’s seat belt.
Page 127 Regular Cab models: Toyota strongly urges use of a proper child restraint system which conforms to the size of the child. Access Cab and Double Cab models: Toyota strongly urges the use of a proper child restraint system that conforms to the size of the child, installed on the rear seat.
Page 128 1-7. Safety information CAUTION Child restraint precautions Access Cab models: Never install a rear-facing child restraint system on the front passenger seat with the passen- ger airbag off switch in the AUTO posi- tion. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-fac-...
Page 129 1-7. Safety information CAUTION Child restraint precautions Bench type front seat: The driver and passengers sit on a bench seat in this vehicle. Therefore, when installing a child restraint system, the seat must be moved back from the SRS airbag as far as possible while also maintaining the driver’s seating position.
Page 130: Installing Child Restraints
1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 131 1-7. Safety information Using the seat belts Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 58) Using the top tether strap Regular Cab models with bench type seat Anchor bracket (for top tether strap) Anchor brackets are pro- vided...
Page 132 1-7. Safety information Regular Cab models with separated type seat Anchor bracket (for top tether strap) Anchor bracket is provided for passenger seat. Access Cab models Anchor bracket (for top tether strap) Anchor brackets are pro- vided for the front passen- seat left rear...
Page 133 1-7. Safety information Double Cab models Anchor bracket (for top tether strap) Anchor brackets are pro- vided for all rear passenger seats. Installing the child restraint system on the front passenger seat (Access Cab models) When you install a child restraint system which belongs to a passen- ger risk group on the front passenger seat, do the following proce- dure.
Page 134 1-7. Safety information CAUTION Rear-facing child restraint system If you must install a rear-facing child restraint system on the front passenger seat, make sure that the passenger airbag off switch is in the OFF position with the key removed and that the indicator light is on. Forward-facing child restraint system A forward-facing child restraint system which belongs to a passenger risk group should never be installed on the front passenger seat with the passen-...
Page 135 1-7. Safety information Vehicles without seatback table (Type A) Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
Page 136 1-7. Safety information Vehicles with seatback table (Type A) Widen the slits of the seat cushion slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched onto...
Page 137 1-7. Safety information Installing on the rear seat Type A Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor.
Page 138 1-7. Safety information Installation with LATCH system (Double Cab models) Type A Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
Page 139 1-7. Safety information Type B Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a...
Page 140 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
Page 141 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
Page 142 1-7. Safety information Booster seat Place the booster seat on the seat facing the front of the vehi- cle. Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle.
Page 143 1-7. Safety information Child restraint systems with a top tether strap (Regular Cab models) Bench type seat Remove the head restraint. Installing position: Right side passenger seat Center passenger seat Swing the seatback forward slightly (→P. 46) and remove the anchor bracket covers.
Page 144 1-7. Safety information Center passenger seat Route the top tether strap through the routing device as shown in the illustration. Make sure the top tether strap is not twisted. Latch the hook onto the anchor bracket. Return the seatback to its orig- inal position.
Page 145 1-7. Safety information Separated type seat Remove the head restraint. Swing the seatback forward slightly (→P. 46) and remove the anchor bracket cover. Store the removed cover in a safe place such as the glove box. Route the top tether strap through the routing device as shown in the illustration.
Page 146 1-7. Safety information Replace the head restraint. Child restraint systems with a top tether strap (Access Cab models) Installing on the front seat Remove the head restraint. Remove the anchor bracket cover. Store the removed cover in a safe place such as the glove box. Secure the child restraint using a seat belt or lower anchors.
Page 147 1-7. Safety information Replace the head restraint. Installing on the rear seat Remove the anchor bracket cov- ers. Store the removed covers in a safe place such as the glove box. Secure the child restraint using a seat belt or lower anchors. Route the top tether strap through the routing device as shown in the illustration.
Page 148 1-7. Safety information Child restraint systems with a top tether strap (Double Cab models) Remove the head restraint. Installing position: Outside passenger seat Center passenger seat Outside passenger seat Swing the seatback forward slightly. (→P. 51) Latch the hook onto the anchor bracket.
Page 149 1-7. Safety information Secure the child restraint using a seat belt or lower anchors, and tighten the top tether strap. Make sure the top tether strap is securely latched. Replace the head restraint. Installing position: Outside passenger seat Center passenger seat Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2.
Page 150 1-7. Safety information CAUTION When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. (→P. 60) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
Page 151 1-7. Safety information CAUTION When installing a child restraint system When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
Page 152: Driving Procedures
2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. Starting the engine →P. 144 Driving Automatic transmission With the brake pedal depressed, shift the shift lever to D. (→P. 147) Release the parking brake. (→P.
Page 153 2-1. Driving procedures Parking the vehicle Automatic transmission With the shift lever in D, depress the brake pedal. Set the parking brake. (→P. 154) Shift the shift lever to P. (→P. 147) When parking on a hill, if necessary, block the wheels. Turn the engine switch off to stop the engine.
Page 154 Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended...
Page 155 Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. Do not under any circumstances shift the shift lever to P, R or N (automatic transmission) or R (manual transmission) while the vehicle is moving.
Page 156 2-1. Driving procedures CAUTION When driving the vehicle Do not shift the shift lever to N while the vehicle is moving. Doing so may cause the engine brake to not operate properly and lead to an accident. Do not turn the engine off while driving. The power steering and brake booster systems will not operate properly if the engine is not running.
Page 157 2-1. Driving procedures CAUTION When driving on slippery road surfaces After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.
Page 158 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
Page 159 CAUTION Exhaust gases Toyota does not recommend occupying the rear cargo area when it is fitted with a slide-in camper, camper shell or other type cover while the engine is running. This caution applies to both driving and stopped or parked situa- tions with the engine running.
Page 160 If you hear a squealing or scraping noise while driving (brake pad wear limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed.
Page 161 Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. Brake function Changes in quantity and quality of oil and fluid used for the engine, trans- mission, transfer (4WD vehicles), differentials, etc.
Page 162: Engine (Ignition) Switch
2-1. Driving procedures Engine (ignition) switch Engine switch LOCK The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in P.) Some electrical components such as the audio system can be used.
Page 163 2-1. Driving procedures Turning the key from ACC to LOCK Shift the shift lever to P (auto- matic transmission) or N (man- ual transmission). (→P. 147, 150) Push in the key and turn to the LOCK position. Steering lock release When starting the engine, the engine switch may seem stuck in the LOCK posi- tion.
Page 164 2-1. Driving procedures CAUTION Caution while driving Do not turn the engine switch to the LOCK position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the ACC position. NOTICE To prevent battery discharge Do not leave the engine switch in the ACC or ON position for long periods if...
Page 165: Automatic Transmission
2-1. Driving procedures ∗ Automatic transmission Select a shift position appropriate for the driving conditions. Shifting the shift lever 5-speed models While the engine switch is on, depress the brake pedal and move the shift lever. ∗ : If equipped I n f o r ma t i o n P r o v i d e d b y :...
Page 166 2-1. Driving procedures 4-speed models While the engine switch is on, depress the brake pedal and move the shift lever. Shift position uses Function Shift position 5-speed models 4-speed models Parking the vehicle or starting the engine Reversing Neutral Normal driving Position for engine brak- —...
Page 167 2-1. Driving procedures Downshifting restrictions The shift lever cannot be downshifted if the following speeds are exceeded. 2WD models mph (km/h) Maximum speed Downshifting 5-speed models 4-speed models 4 → 3 82 (133) — 3 → 2 54 (88) 74 (119) 2 →...
Page 168: Manual Transmission
2-1. Driving procedures ∗ Manual transmission Shifting the shift lever 6-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly. 5-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly.
Page 169 2-1. Driving procedures Maximum allowable speed Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. 2WD models except PreRunner mph (km/h) Maximum speed Shift position 6-speed models 5-speed models 32 (52) 33 (53) 61 (99) 63 (101) 91 (146) 90 (146)
Page 170 2-1. Driving procedures 4WD models mph (km/h) Maximum speed Shift position Transfer position 6-speed models 5-speed models H2 and H4 30 (49) 30 (48) 11 (19) 11 (18) H2 and H4 58 (93) 57 (92) 22 (36) 22 (36) H2 and H4 85 (137) 82 (133) 33 (53)
Page 171: Turn Signal Lever
2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 172: Parking Brake
2-1. Driving procedures Parking brake Lever type l Sets the parking brake Fully set the parking brake U.S.A. Canada while depressing the brake pedal. At this time, the indicator will come on. l Release the parking brake Press the button Turn the lever clockwise Press it in completely Pedal type...
Page 173 2-1. Driving procedures Parking brake engaged warning buzzer The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reach a speed of 3 mph [5 km/h]). Usage in winter time See “Winter driving tips” for parking brake usage in winter time. (→P. 210) NOTICE Before driving Fully release the parking brake.
Page 174: Horn
2-1. Driving procedures Horn To sound the horn, press on or close to the mark. After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
Page 175 2-1. Driving procedures I n f o r ma t i o n P r o v i d e d b y :...
Page 176 2-1. Driving procedures I n f o r ma t i o n P r o v i d e d b y :...
Page 177 2-1. Driving procedures I n f o r ma t i o n P r o v i d e d b y :...
Page 178 2-1. Driving procedures I n f o r ma t i o n P r o v i d e d b y :...
Page 179: Gauges And Meters
2-2. Gauges and meters Gauges and meters The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Engine coolant temperature gauge Displays the engine coolant temperature.
Page 180 2-2. Gauges and meters Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.
Page 181 2-2. Gauges and meters NOTICE To prevent damage to the engine and its components Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. The engine may be overheating if the engine coolant temperature gauge is in the red zone (H).
Page 182: Indicators And Warning Lights
2-2. Gauges and meters Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster Center panel I n f o r ma t i o n P r o v i d e d b y :...
Page 183 2-2. Gauges and meters Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Slip indicator (→P. 153) (→P. 182, 184, 193) Headlight high beam VSC OFF indicator indicator (→P. 165) (→P. 184, 194) Downhill assist control Headlight indicator system indicator...
Page 184 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
Page 185 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 186: Accessory Meter
2-2. Gauges and meters ∗ Accessory meter Outside temperature Displays the outside air temperature. (→P. 322) Compass Displays the direction that the vehicle is heading. (→P. 347) Display button Every time you press this button, the display toggles through the following infor- mation.
Page 187: Operating The Lights And Wipers
2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually. Turning the end of the lever turns on the lights as follows: Vehicles with daytime running light system: The daytime running lights turn on. The side marker, park- ing, tail, license plate, daytime running lights equipped)
Page 188 2-3. Operating the lights and wipers Daytime running light system (if equipped) To make your vehicle more visible to other drivers, the front turn signal lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night.
Page 189: Fog Light Switch
2-3. Operating the lights and wipers ∗ Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. On/off The fog lights can be turned on only when The headlights are on low beam. ∗...
Page 190: Windshield Wipers And Washer
2-3. Operating the lights and wipers Windshield wipers and washer Without intermittent type Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Washer operation I n f o r ma t i o n P r o v i d e d b y :...
Page 191 2-3. Operating the lights and wipers Intermittent wiper with interval adjuster Wiper intervals can be adjusted for intermittent operation (when is selected). Intermittent windshield wiper operation Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency...
Page 192 2-3. Operating the lights and wipers Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. The windshield wiper and washer can be operated when The engine switch must be in the ON position. If no windshield washer fluid sprays Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.
Page 193: Using Other Driving Systems
2-4. Using other driving systems ∗ Cruise control Use cruise control to maintain a set speed without using the acceler- ator. Indicator Cruise control switch Set the vehicle speed Press the ON-OFF button to turn the cruise control on. At this time, the cruise control indicator will come on.
Page 194 2-4. Using other driving systems Adjusting the speed setting Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.
Page 195 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. CAUTION To avoid operating the cruise control by mistake Keep the ON-OFF button off when not in use.
Page 196: Rear View Monitor System (Vehicles With Auto Anti-Glare Inside Rear View Mirror)
2-4. Using other driving systems Rear view monitor system (vehicles with auto anti-glare inside rear view mirror) The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen.
Page 197 2-4. Using other driving systems Switching the screen ON/OFF mode While displaying the screen, press the AUTO button on the inside rear view mir- ror to switch the screen ON/OFF mode. Screen ON mode: Green indicator comes Screen OFF mode: Orange indicator comes on.
Page 198 2-4. Using other driving systems Rear view monitor system camera In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly. The vehicle is in a dark area, such as at night.
Page 199 Conditions which may affect the rear view monitor system If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer. As the camera has a water proof construction, do not detach, disassemble or modify it.
Page 200: Four-Wheel Drive System
2-4. Using other driving systems ∗ Four-wheel drive system Use the front-wheel drive control switch to select the following transfer modes. H2 (high speed position, two-wheel drive) Normal driving H4 (high speed position, four-wheel drive) Greater traction than two wheel drive. When you experience a loss of power, such as wheel slipping.
Page 201 2-4. Using other driving systems Shifting between H4 and L4 Shifting from H4 to L4 Automatic transmission Stop the vehicle completely. Shift the shift lever to N. Push and turn the front-wheel drive control switch fully clock- wise. If the four-wheel drive indicator flashes and the buzzer sounds, try the above steps again.
Page 202 If the indicator light continues to blink even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the four-wheel drive system.
Page 203 2-4. Using other driving systems Shifting to L4 VSC is automatically turned off. Four-wheel drive usage frequency You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front-drive components are lubricated. CAUTION Caution while driving Never operate the front-wheel drive control switch if the wheels are slipping.
Page 204: Active Traction Control System
2-4. Using other driving systems ∗ Active traction control system The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces. System operation Vehicles with an automatic transmission: Stop the vehicle, shift the shift lever to N and put the front- wheel drive control switch in the L4 position.
Page 205 2-4. Using other driving systems When the rear differential is locked (vehicles with the rear differential lock system) The active traction control system is activated only when the vehicle speed is less than 3 mph (6 km/h). Sounds and vibrations caused by the active traction control system A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move.
Page 206: Auto Lsd System
2-4. Using other driving systems AUTO LSD system The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when one of the rear wheels spin- ning occurs in a ditch or rough surface.
Page 207 2-4. Using other driving systems Automatic VSC reactivation If the AUTO LSD system is turned on and the vehicle speed decreases, the VSC system will turn off and the VSC OFF indicator will turn on. If the vehi- cle speed increases the VSC system will turn on and the VSC OFF indicator will turn off.
Page 208: Rear Differential Lock System
2-4. Using other driving systems ∗ Rear differential lock system The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning.
Page 209 2-4. Using other driving systems Manual transmission 4WD models: Before using the rear differential lock system. Stop the vehicle or reduce your speed to less than 2 mph (3 km/h). Depress the clutch pedal and put the front-wheel drive control switch in the L4 position to see if this is sufficient. If this has no effect, additionally use the rear differential lock system.
Page 210 2-4. Using other driving systems After unlocking the rear differential To check that the indicator goes off, turn the engine switch to the ON posi- tion, but do not start the engine. CAUTION To avoid an accident Do not use the rear differential lock system except when wheel spinning occurs in a ditch or on a slippery or ragged surface.
Page 211: Downhill Assist Control System
2-4. Using other driving systems ∗ Downhill Assist Control system The downhill assist control system helps to prevent excessive speed on steep downhill descents. System operation The system will operate when the vehicle is traveling under 15 mph (25 km/h) and the front-wheel drive control switch is in the L4 position.
Page 212 ON position. The downhill assist control system indicator does not come on when the DAC switch is pressed. In the above cases have your vehicle checked by your Toyota dealer. CAUTION Do not rely excessively on the downhill assist control system It may not be able to maintain a low speed over road surfaces on which slid- ing can easily occur, such as extremely steep slopes or icy or muddy roads.
Page 213: Clutch Start Cancel Switch
2-4. Using other driving systems ∗ Clutch start cancel switch The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged. Never use the switch for normal engine starting. Be sure to follow the starting procedure.
Page 214: Driving Assist Systems
2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ABS (Anti-lock Brake System) Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.
Page 215 2-4. Using other driving systems When the VSC/TRAC/hill-start assist control systems are operating If the vehicle is in danger of slip- ping, the rear wheels (2WD mod- els) four wheels (4WD models) spin, the vehicle starts to roll backwards when starting on an incline, this indicator flashes to indicate that the VSC/ TRAC/hill-start...
Page 216 2-4. Using other driving systems Turning off TRAC and VSC Press and hold the VSC OFF switch for more than 3 seconds while the vehicle is stopped to turn off both TRAC and VSC. The VSC OFF indicator light should come on. Push the switch again to turn both systems back on.
Page 217 2-4. Using other driving systems Hill-start assist control is operational when (if equipped) The shift lever is in the D, 4, 3, 2 (5-speed automatic transmission), D, 3, 2 (4-speed automatic transmission) or L positions. The brake pedal is not depressed. Hill-start assist control will not operate when (if equipped) The shift lever is in the P, R or N positions.
Page 218 The ABS and VSC will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. I n f o r ma t i o n P r o v i d e d b y :...
Page 219 2-4. Using other driving systems CAUTION Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction. I n f o r ma t i o n P r o v i d e d b y :...
Page 220: Driving Information Off-Road Precautions (4Wd Models And Prerunner)
2-5. Driving information Off-road precautions (4WD models and PreRunner) This vehicle has higher ground clearance and narrower tread in rela- tion to the height of its center of gravity to make it capable of per- forming in a wide variety of off-road applications. Off-road vehicle feature l Specific design characteristics give it a higher center of gravity than ordinary passenger cars.
Page 221 2-5. Driving information CAUTION Off-road vehicle precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.
Page 222 2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. l Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
Page 223 2-5. Driving information CAUTION Off-road driving precautions Always observe the following precautions to minimize the risk of serious injury or damage to your vehicle: Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places. Do not grip the steering wheel spokes when driving off-road.
Page 224 2-5. Driving information NOTICE To prevent the water damage Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. Water entering the engine air intake will cause severe engine damage. Water entering the automatic transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ulti- mately damage.
Page 225: Cargo And Luggage
For better fuel economy, do not carry unnecessary weight. Deck rails Headboard rail Side rails To use the deck rails, you must install genuine Toyota accessories or their equiva- lent for the deck rails. Follow manufacturer’s instructions and precautions...
Page 226 2-5. Driving information CAUTION When you secure cargo with the deck rails Spread out tie-down/support locations evenly along the length of the rails. Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail. To prevent luggage or cargo from sliding forward during braking, make sure the deck rail accessories such as storage box are securely attached on the deck rails.
Page 227 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Example on your vehicle Cargo capacity Total load capacity...
Page 228 2-5. Driving information CAUTION Things that must not be carried in the luggage compartment The following things may cause a fire if loaded in the luggage compart- ment. Receptacles containing gasoline Aerosol cans Storage precautions Observe the following precautions. Failing to do so may result in death or serious injury. Do not stack anything behind the front seats higher than the seat- backs.
Page 229 2-5. Driving information CAUTION Capacity and distribution Do not exceed the maximum axle weight rating or the total vehicle weight rating. Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.
Page 230: Vehicle Load Limits
2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. Total load capacity: (→P. 485) Total load capacity means the combined weight of occupants, cargo and luggage. Seating capacity: Regular Cab models With separated type seats—...
Page 231 2-5. Driving information CAUTION Overloading the vehicle Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident. I n f o r ma t i o n P r o v i d e d b y :...
Page 232: Winter Driving Tips
2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. Pre-winter preparations l Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 233 2-5. Driving information When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. When parking the vehicle Park the vehicle and move the shift lever to P (automatic trans- mission) or 1 or R (manual transmission) without setting the parking brake.
Page 234 2-5. Driving information Snow chain installation Observe the following precautions when installing and removing chains. Install and remove tire chains in a safe location. Install tire chains on the rear tires only. Do not install tire chains on the front tires. Install tire chains following the instructions provided in the accompanying instructions.
Page 235 NOTICE Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 236: Trailer Towing
To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as towing kits, etc.
Page 237 2-5. Driving information Towing related terms GCWR (Gross Combination Weight Rating) The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
Page 238 2-5. Driving information TWR (Trailer Weight Rating) The maximum allowable gross (With brakes) trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer. TWR is calculated assuming base vehicle with one driver, one front passenger, towing package (if available), hitch and hitch sys- tems (if required).
Page 239 2-5. Driving information Weight limits l The gross trailer weight must never exceed the TWR described in the table. (→P. 218, 487) l The gross combination weight must never exceed the GCWR described in the table. (→P. 218) Regular Cab models and Double Cab models l The gross vehicle weight must never exceed the GVWR indi- cated...
Page 240 2-5. Driving information Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. GCWR and TWR Regular Cab models Driving Model code Engine GCWR system TRN220L- 7140 lb. TRMDKA (3238 kg) TRN220L-...
Page 241 2-5. Driving information Access Cab models Driving Model code Engine GCWR system TRN225L- 7430 lb. CRMDKA (3370 kg) TRN225L- 7450 lb. (3379 kg) CRPDKA 2.7 L TRN245L- 4-cylinder 7790 lb. 3500 lb. CRMDKA (2TR-FE) (3533 kg) (1587 kg) engine TRN245L- 7810 lb.
Page 242 2-5. Driving information Double Cab models Driving Model code Engine GCWR system TRN225L- 7530 lb. 3400 lb. 2.7 L PRPDKA (3415 kg) (1542 kg) 4-cylinder (2TR-FE) TRN265L- 7660 lb. 3500 lb. engine PRPDKA (3474 kg) (1587 kg) 8040 lb. 3500 lb. (3646 kg) (1587 kg) GRN245L-...
Page 243 Unbraked TWR 1000 lb. (453 kg) Fifth wheel and gooseneck towing TWR Toyota does not recommend fifth wheel and gooseneck towing. : These models meet the tow-vehicle trailering requirement of SAE International per SAE J2807. I n f o r ma t i o n P r o v i d e d b y :...
Page 244 2-5. Driving information Trailer Tongue Weight l A recommended tongue weight varies in accordance with the types of trailers or towing as described below. l To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. •...
Page 245 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. l If you wish to install a trailer hitch, contact your Toyota dealer. l Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
Page 246 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
Page 247 2-5. Driving information Positions for towing hitch receiver and hitch ball Weight carrying ball position: 56.1 in. (1425 mm) Hitch receiver pin hole posi- tion: 44.2 in. (1123 mm) Connecting trailer lights Use the wire harness stored in the rear end under the vehicle body.
Page 248 Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. l Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
Page 249 2-5. Driving information l Avoid jerky starts or sudden acceleration. l Avoid jerky steering and sharp turns, and slow down before mak- ing a turn. l Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.
Page 250 2-5. Driving information l Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in 1 or R (manual transmission). Avoid parking on a slope, but if unavoid- able, do so only after performing the following: Apply the brakes and keep them applied.
Page 251 2-5. Driving information Matching trailer ball height to trailer coupler height No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer. Coupler Trailer ball Before towing...
Page 252 Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
Page 253 2-5. Driving information If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases. CAUTION Trailer towing precautions To tow a trailer safely, use extreme care and drive the vehicle in accordance...
Page 254 When towing a trailer Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. If the gross trailer weight exceeds unbraked TWR, trailer brakes are required.
Page 255 2-5. Driving information NOTICE When installing a trailer hitch Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. Do not directly splice trailer lights Do not directly splice trailer lights. Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.
Page 256: Dinghy Towing
2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground. I n f o r ma t i o n P r o v i d e d b y :...
Page 257: Using The Air Conditioning System And Defogger
3-1. Using the air conditioning system and defogger Air conditioning system Type A Temperature control dial Fan speed control dial Air outlet selection dial Outside air or recirculated air mode switch Type B Temperature control dial Fan speed control dial Air outlet selection dial Outside air or recirculated Air conditioning...
Page 258 3-1. Using the air conditioning system and defogger Adjusting the settings Adjusting the temperature setting (Type A) Turn the temperature control dial clockwise to increase the temper- ature. Adjusting the temperature setting (Type B) Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).
Page 259 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the upper body and feet. Double Cab models only When the dial is set to , air flows to the feet. Double Cab models only When the dial is set to , air flows to the feet and the wind-...
Page 260 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the windshield and side windows. The air intake selector is automat- ically set to outside air mode. In this position, the air intake selector cannot be changed to the recirculated air mode.
Page 261 3-1. Using the air conditioning system and defogger Adjusting the position of the air outlets Center outlets Direct air flow to the left or right, up or down. I n f o r ma t i o n P r o v i d e d b y :...
Page 262 3-1. Using the air conditioning system and defogger Right and left side outlets Direct air flow to the left or right, up or down. Opening and closing the air outlets Center outlets Open the vent. Close the vent. I n f o r ma t i o n P r o v i d e d b y :...
Page 263 3-1. Using the air conditioning system and defogger Right and left side outlets Open the vent. Close the vent. For quick clearing of the windshield and side windows (type B only) Press to turn the air conditioning on. Using the system in recirculated air mode The windows will fog up more easily if the recirculated air mode is used for an extended period.
Page 264 3-1. Using the air conditioning system and defogger CAUTION To prevent the windshield from fogging up Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.
Page 265: Using The Audio System
3-2. Using the audio system Audio system types Type A: CD player with CD changer controller and AM/FM radio Type B: CD player with changer and AM/FM radio Type A Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 266 3-2. Using the audio system Title Page Using the radio P. 247 Using the CD player P. 253 Playing back MP3 and WMA discs P. 259 Optimal use of the audio system P. 267 Operating the sub woofer P. 270 Using the AUX port P.
Page 267 3-2. Using the audio system CAUTION For vehicles sold in U.S.A. and Canada Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device. Laser products •...
Page 268: Using The Radio
3-2. Using the audio system Using the radio Power Volume Adjusting the Station selector frequency Scanning for receivable stations AM/FM mode buttons Seeking the frequency ® Setting station presets (excluding XM Satellite Radio) ∧ Search for desired stations by turning or pressing “...
Page 269 3-2. Using the audio system Scanning all radio stations within range Press All stations with reception will be played for 5 seconds each. When the desired station is reached, press the button once again to stop scanning. ® Satellite Radio (if equipped) ®...
Page 270 3-2. Using the audio system Displaying text information Press The display will show up to 10 characters. The display changes as follows each time the button is pressed. l CH NAME l TITLE (SONG/PROGRAM TITLE) l NAME (ARTIST NAME/FEATURE) l CH NUMBER When the battery is disconnected Stations presets are erased.
Page 271 XM antenna cable is attached securely. ANTENNA There is a short-circuit in the antenna or the sur- rounding antenna cable. See a Toyota certified dealer. ® You have not subscribed to the XM Satellite Radio. The radio is being updated with the latest ®...
Page 272 3-2. Using the audio system The unit is acquiring audio or program information. LOADING Wait until the unit has received the information. The channel you selected is not broadcasting any OFF AIR programming. Select another channel. There is no song/program title or artist name/fea- ----- ture associated with the channel at that time.
Page 273 3-2. Using the audio system NOTICE To prevent damage, remove the antenna in the following cases. The antenna will touch the ceiling of a garage. A cover will be put on the vehicle. I n f o r ma t i o n P r o v i d e d b y :...
Page 274: Using The Cd Player
3-2. Using the audio system Using the CD player CD selection Power Volume (type A with Fast-forward changer and type B) CD load CD eject Reverse (type B only) Random Display text playback message Search playback Repeat play Track selection Playback Loading CDs Loading a CD (type A)
Page 275 3-2. Using the audio system Insert a CD when the indicator on the slot turns from amber to green. The display changes from “WAIT” to “LOAD”. The indicator on the slot turns to amber when the CD is inserted. Insert the next CD when the indicator on the slot turns from amber to green again.
Page 276 3-2. Using the audio system Fast-forwarding and reversing tracks To fast-forward or reverse. Press and hold Selecting a CD (type A with a CD changer and type B) Selecting the desired CD Press Selecting loaded CDs Press and hold until you hear a beep. The first 10 seconds of the first track on each CD will be played.
Page 277 3-2. Using the audio system Switching the display Press Each time the switch is pressed, the display changes in the order of Track no./Elapsed time→CD title→Track name. Display Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding for 1 second or more will display the remaining characters.
Page 278 3-2. Using the audio system If CDs are left inside the CD player or in the ejected position for extended periods CDs may be damaged and may not play properly. Lens cleaners Do not use lens cleaners. Doing so may damage the CD player. NOTICE CDs and adapters that cannot be used Do not use the following types of CDs or 3 in.
Page 279 3-2. Using the audio system NOTICE CDs that have had tape, stickers or CD- R labels attached to them, or that have had the label peeled off CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself.
Page 280: Playing Back Mp3 And Wma Discs
3-2. Using the audio system Playing back MP3 and WMA discs Power Volume Disc selection Fast-forward (type B only) Disc load (type B only) Disc eject Reverse Random File selection playback Search playback Repeat play Playback File selection Display text message Folder selection Loading MP3 and WMA discs Loading a disc (type A)
Page 281 3-2. Using the audio system Loading multiple discs (type B only) Press and hold until you hear a beep. “WAIT” is shown on the display. Insert a disc when the indicator on the slot turns from amber to green. The display changes from “WAIT” to “LOAD”. The indicator on the slot turns to amber when the disc is inserted.
Page 282 3-2. Using the audio system Selecting a folder Selecting folders one at a time To select the desired folder, press “∧” or “∨” on Selecting the desired folder by cueing the first file of each folder Press and hold until you hear a beep. The first 10 seconds of the first file in the each folder will be played.
Page 283 3-2. Using the audio system Repeat play Repeating a file Press Repeating all of the files in the folder Press and hold until you hear a beep. Random playback Playing files from a particular folder in random order Press Playing all of the files on a disc in random order Press and hold until you hear a beep.
Page 284 3-2. Using the audio system Display Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding for 1 second or more will display the remaining characters. A maximum of 24 characters can be displayed. is pressed for 1 second or more again or has not been pressed for 6 seconds or more, the display will return to the first 12 characters.
Page 285 3-2. Using the audio system Lens cleaners Do not use lens cleaners. Doing so may damage the MP3 and WMA player. MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression.
Page 286 3-2. Using the audio system Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.
Page 287 3-2. Using the audio system MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played. To make the file check finish more quickly, we recommend you do not write in any files other than MP3 or WMA files or create any unnec- essary folders.
Page 288: Optimal Use Of The Audio System
3-2. Using the audio system Optimal use of the audio system Displays the current mode Changes the following set- ting • Sound quality and volume balance (→P. 268) The sound quality and bal- ance setting can be changed to produce the best sound. •...
Page 289 3-2. Using the audio system Adjusting sound quality Turning adjusts the level. Sound qual- Mode Turn to the Turn to the Level ity mode displayed left right Bass -5 to 5 Midrange -5 to 5 High Treble -5 to 5 Shifts to roof /roof...
Page 290 3-2. Using the audio system JBL brand audio system When “ASL” is selected, turning to the right turns “ASL” on, and turning to the left turns “ASL” off. ASL automatically adjusts the volume and tone quality according to vehi- cle speed. I n f o r ma t i o n P r o v i d e d b y :...
Page 291: Operating The Sub Woofer
3-2. Using the audio system Operating the sub woofer (on some Access Cab models) LIGHT ON The sub woofer illumination turns on. In this position, the sub woofer operates. I n f o r ma t i o n P r o v i d e d b y :...
Page 292: Using The Aux Port
3-2. Using the audio system Using the AUX port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Connect the portable audio device. Press I n f o r ma t i o n P r o v i d e d b y :...
Page 293 3-2. Using the audio system Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle’s audio controls. All other adjustments must be made on the portable audio device itself. When using a portable audio device connected to the power outlet or cigarette lighter Noise may occur during playback.
Page 294: Using The Steering Wheel Audio Switches
3-2. Using the audio system ∗ Using the steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Volume Radio: Select radio stations Select tracks, files (MP3 and WMA) and discs Power on/off, select audio source Turning on the power Press...
Page 295 3-2. Using the audio system Type B: →SAT2 →SAT3 FM1→FM2→CD changer→AUX→AM→SAT1 : If installed with a CD changer : If equipped Adjusting the volume Press “+” on to increase the volume and “–” to decrease the volume. Press and hold “+” or “–” on to continue increasing or decreasing the volume.
Page 296 3-2. Using the audio system Selecting a folder (type A) Press to select the CD mode. Press and hold “∧” or “∨” on until you hear a beep. Selecting a disc in the CD player (type A with a CD changer and type B) Press to select the CD mode.
Page 297: Using The Hands-Free Phone System (For Cellular Phone) Hands-Free Phone System (For Cellular Phone)
3-3. Using the hands-free phone system (for cellular phone) ∗ Hands-free phone system (for cellular phone) ® This system supports Bluetooth , which allows you connect a cellu- lar phone without using cables and to make or receive calls without operating the cellular phone buttons.
Page 298 3-3. Using the hands-free phone system (for cellular phone) Conditions under which the system will not operate ® If using a cellular phone that does not support Bluetooth If the cellular phone is switched off If you are outside service range If the cellular phone is not connected If the cellular phone’s battery is low ®...
Page 299 3-3. Using the hands-free phone system (for cellular phone) Certification for the hands-free phone system FCC ID: ACJ932C5ZZZ035 IC ID: 216J-C5ZZZ035 MADE IN U.S.A. NOTE: This device complies with Part 15 of the FCC Rules and RSS-210 of industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired oper- ation.
Page 300 3-3. Using the hands-free phone system (for cellular phone) FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.
Page 301: Using The Hands-Free Phone System
3-3. Using the hands-free phone system (for cellular phone) Using the hands-free phone system Audio unit ® Displays Bluetooth con- nection condition If “BT” is not displayed, the hands-free phone system cannot be used. Displays the reception level Displays such items as numbers, names, mes-...
Page 302 3-3. Using the hands-free phone system (for cellular phone) Steering wheel telephone switches Volume The voice guidance volume cannot be adjusted by using this switch. Hands-free phone system off/ends a call/refuses a call Hands-free phone system on/starts a call Press: Voice command sys- tem on Press and hold: Voice com- mand system off...
Page 303 3-3. Using the hands-free phone system (for cellular phone) Operating the system by using a voice command By following voice guidance instructions output from the speaker, you can speak voice commands aloud to control the hands-free phone system without looking at the display or operating Operation procedure when using voice commands Press and say a voice command for a desired function.
Page 304 3-3. Using the hands-free phone system (for cellular phone) Register a phone name by either of the following methods. a. Select “(RECORD NAME)” by using , and say aloud the name you would like to register for the phone. b. Press and say aloud the name you would like to reg- ister for the phone.
Page 305 3-3. Using the hands-free phone system (for cellular phone) Second First menu Third menu Operation detail menu Dialing a phone number Callback stored in the incoming his- (CALLBACK) tory memory By voice (BY VOICE) By phone (BY PHONE) Add entry Adding a new phone num- (ADD Call history...
Page 306 3-3. Using the hands-free phone system (for cellular phone) Second First menu Third menu Operation detail menu Set PIN Setting a PIN (SET PIN) Phone book lock Security Locking the phone book (PHBK (SECU- LOCK) RITY) Phone book unlock Unlocking the phone book (PHBK UNLOCK) Pair phone...
Page 307 3-3. Using the hands-free phone system (for cellular phone) Using a short cut voice command First menu Second menu Operation detail Dialing a phone number reg- Dial “XXX (name)” istered in the phone book Phone book add Adding a new phone number entry Changing the name of a Phone book change...
Page 308 3-3. Using the hands-free phone system (for cellular phone) Automatic adjustment of volume When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less. When using a voice command For numbers, speak a combination of single digits from zero to nine, # (pound), ∗...
Page 309: Making A Phone Call
3-3. Using the hands-free phone system (for cellular phone) Making a phone call Making a phone call l Dialing by inputting a phone number “Dial by number” l Dialing by inputting a name “Dial by name” l Speed dialing l Dialing a phone number stored in the outgoing history mem- “Redial”...
Page 310 3-3. Using the hands-free phone system (for cellular phone) Dial by one of the following methods: a. Press b. Press and say “Dial”. c. Select “Dial” by using Dialing by inputting a name Press and say “Dial by name”. Select a registered name to be input by either of the following methods: a.
Page 311 3-3. Using the hands-free phone system (for cellular phone) When receiving a phone call Answering the phone Press Refusing the call Press Transferring a call A call can be transferred between the cellular phone and system while dialing, receiving a call, or conversing a call. Use one of the fol- lowing methods: a.
Page 312 3-3. Using the hands-free phone system (for cellular phone) Using a call history memory Follow the procedure below to use a phone number stored in call his- tory memory: Press and say “Redial” (when using a phone number stored in the outgoing history memory) or “Callback” (when using a phone number stored in the incoming history mem- ory).
Page 313 3-3. Using the hands-free phone system (for cellular phone) A shortcut to Redial is available Press the twice. Muting your voice Your voice can be muted so that the other party cannot hear your voice dur- ing a call. To set or cancel: Press and say “Mute”.
Page 314: Setting A Cellular Phone
3-3. Using the hands-free phone system (for cellular phone) Setting a cellular phone Registering a cellular phone in the hands-free phone system allows the system to function. The following function can be used for regis- tered cellular phones: Functions and operation procedures To enter a menu for each function, follow the steps below by using voice commands or l Registering a cellular phone...
Page 315 3-3. Using the hands-free phone system (for cellular phone) Selecting a cellular phone to be used Select “Select phone” by using a voice command or Pattern A Select a cellular phone to be used by either of the following methods, and select “Confirm” by using a voice command or a.
Page 316 3-3. Using the hands-free phone system (for cellular phone) b.Press and say “List phones”. While the desired phone name is being read aloud, press c. Select the desired phone name by using Press or select “(RECORD NAME)” by using and say a new name. Select “Confirm”...
Page 317 3-3. Using the hands-free phone system (for cellular phone) Changing the passkey Select “Set passkey” by using a voice command or Pattern A Press , say a four to eight-digit number, and select “Confirm” by using a voice command or Pattern B Select a four to eight-digit number by using The number should be input one digit at a time.
Page 318 3-3. Using the hands-free phone system (for cellular phone) b. Press and say “List phones”. While the name of the desired cellular phone is being read aloud, press Pattern B Select a cellular phone to be deleted by using The number of cellular phones that can be registered Up to 6 cellular phones can be registered in the system.
Page 319: Security And System Setup
3-3. Using the hands-free phone system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: Security setting items and operation procedure l Setting or changing the PIN (Personal Identification Number) 1. “Setup” → 2. “Security” → 3. “Set PIN” l Locking the phone book 1.
Page 320 3-3. Using the hands-free phone system (for cellular phone) Changing the PIN Select “Set PIN” by using a voice command or Enter the registered PIN by using a voice command or Enter a new PIN by using a voice command or When using , input the number one digit at a time.
Page 321 3-3. Using the hands-free phone system (for cellular phone) Setting voice guidance volume Select “(GUIDANCE VOL)” by using Change the voice guidance volume. To decrease the volume: Turn counterclockwise. To increase the volume: Turn clockwise. Initialization Select “(INITIALIZE)” and then “(CONFIRM)” by using Select “(CONFIRM)”...
Page 322: Using The Phone Book
3-3. Using the hands-free phone system (for cellular phone) Using the phone book To enter the menu of each setting, follow the steps below: l Adding a new phone number 1. “Phone book” → 2. “Add entry” l Changing a registered name 1.
Page 323 3-3. Using the hands-free phone system (for cellular phone) Adding procedure Select “Add entry” by using a voice command or Use one of the following methods to input a phone number: Inputting a phone number by using voice commands STEP2-1 Select “By voice” by using a voice command or STEP2-2 Press , say the desired phone number, and select “Confirm”...
Page 324 3-3. Using the hands-free phone system (for cellular phone) Selecting a phone number from outgoing or incoming history mem- STEP2-1 Select “Call history” by using a voice command or STEP2-2 Select “Outgoing” or “Incoming” by using a voice command or STEP2-3 Select the data to be registered by either of the fol- lowing methods: a.
Page 325 3-3. Using the hands-free phone system (for cellular phone) Select the name to be registered by either of the following methods, and select “Confirm” by using a voice command or a. Press and say the desired name. b. Select “(RECORD NAME)” by using , and say the desired name.
Page 326 3-3. Using the hands-free phone system (for cellular phone) c. Select the desired data by using Select the desired preset button, and register the data into speed dial by either of the following methods: a. Press the desired preset button, and select “Confirm” by using a voice command or b.
Page 327 3-3. Using the hands-free phone system (for cellular phone) Deleting registered data Select “Delete entry” by using a voice command or Pattern A Select data to be deleted by either of the following methods, and select “Confirm” by using a voice command or a.
Page 328 3-3. Using the hands-free phone system (for cellular phone) Listing the registered data Select “List names” by using a voice command and the system begins reading aloud the list of the registered data. When listing is complete, the system returns to “Phone book”. Pressing while an entry is being read aloud selects the entry, and the following functions will be available.
Page 329: Using The Interior Lights
3-4. Using the interior lights Interior lights list Interior light (→P. 309) Personal lights (if equipped) (→P. 309) Illuminated entry system When the interior light switch is in the DOOR position, the interior light auto- matically turns on/off according to whether the doors are locked/unlocked and whether the doors are open/closed.
Page 330: Interior Light
3-4. Using the interior lights Interior light and personal lights Interior light DOOR position Personal lights (if equipped) On/off I n f o r ma t i o n P r o v i d e d b y :...
Page 331: Using The Storage Features
3-5. Using the storage features List of storage features Glove box Overhead console (Access Cab and Double Cab models) Bottle holders Console boxes (if equipped) Auxiliary boxes Cup holders CAUTION Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: Glasses may be deformed by heat or cracked if they come into contact...
Page 332: Glove Box
3-5. Using the storage features Glove box and console boxes Glove box Pull up the lever. CAUTION Caution while driving Keep the glove box closed. Injuries may result in the event of an accident or sudden braking. Console boxes (if equipped) Front (Separated type front seat) Push the button.
Page 333: Cup Holders
3-5. Using the storage features Console boxes and cup holders Rear (Access Cab models) Lift the lid while pulling the knob. CAUTION Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking. Cup holders Type A (Bench type front seat) I n f o r ma t i o n P r o v i d e d b y :...
Page 334 3-5. Using the storage features Cup holders Type B (Separated type front seats with an automatic transmis- sion) Type C (Separated type front seats with a manual transmission) Removing the cup holder Type A (Bench type front seat) Pull the cup holder up. I n f o r ma t i o n P r o v i d e d b y :...
Page 335: Bottle Holders
3-5. Using the storage features Cup holders and bottle holders Type B (Separated type front seats with an automatic transmission) Pull the cup holder up. CAUTION Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 336 3-5. Using the storage features Bottle holders Front console box (Separated type front seat) Rear (Double Cab models) Bottle holders Depending on their size or shape, some bottles may not fit in the holders. NOTICE Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle.
Page 337: Auxiliary Boxes
3-5. Using the storage features Auxiliary boxes Auxiliary boxes Front Pull the lid down. Under the rear seats (Access Cab models) Pull up the lever. Raise the bottom cushion up. Turn the knob counterclockwise. I n f o r ma t i o n P r o v i d e d b y :...
Page 338 3-5. Using the storage features Auxiliary boxes Open the lid. Press the lid against the bot- tom of the lower cushion until it is supported by the hook- and-loop fastener. Make sure that the lid is sup- ported to prevent it from closing unexpectedly.
Page 339: Overhead Console
3-5. Using the storage features Overhead console Overhead console (Access Cab and Double Cab models) The overhead console is useful for temporarily storing sunglasses and similar small items. Pull the lid down while pushing the knob. CAUTION Caution while driving Keep the overhead console closed.
Page 340: Other Interior Features
3-6. Other interior features Sun visors Type A Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Side extender: Place in side position, then slide backwards. Type B Forward position: Flip down. Side position: Flip down, unhook, and swing to the side.
Page 341: Vanity Mirrors
3-6. Other interior features Vanity mirrors Type A Slide the cover. Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 342: Clock
3-6. Other interior features Clock Adjusts the hours Adjusts the minutes The clock is displayed when The engine switch is in the ACC or ON position. When disconnecting and reconnecting battery terminals The time display will automatically be set to 1:00. I n f o r ma t i o n P r o v i d e d b y :...
Page 343: Outside Temperature Display (Vehicles With Accessory Meter)
(Fahrenheit) and °C (Celsius). When – –°F or – –°C is displayed The system may be malfunctioning. Take your vehicle to your Toyota dealer. The outside air temperature is displayed when The engine switch is in the ON position. When disconnecting and reconnecting battery terminals The display will automatically be set to the initial mode.
Page 344: Cigarette Lighter
3-6. Other interior features Cigarette lighter Push the cigarette lighter. The cigarette lighter will pop up when it is ready for use. The cigarette lighter can be used when The engine switch is in the ACC or ON position. CAUTION To avoid burns or fires Do not touch the metal parts of the cigarette lighter.
Page 345: Power Outlet (12V Dc)
3-6. Other interior features Power outlet (12V DC) The power outlet can be used for 12V accessories that run on less than 10A. The power outlet can be used when The engine switch is in the ACC or ON position. NOTICE To avoid damaging the power outlet Close the power outlet lid when not in use.
Page 346: Power Outlet (115V Ac)
3-6. Other interior features ∗ Power outlet (115V AC) The power outlet can be used for electrical appliances. Main switch To use the power outlet, turn on the main switch. The power supply starts a few seconds after the main switch is pressed.
Page 347 3-6. Other interior features • The shift lever is in N and the clutch pedal is not depressed. (manual transmission) A maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again under condition described above.
Page 348 If the power supply is not resumed even after performing the above proce- dure, have the vehicle inspected by a Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 349 Do not modify, disassemble or repair the power outlet or its inverter, in any way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs. To prevent injuries and accidents, securely fix all electric appliances...
Page 350 3-6. Other interior features NOTICE To avoid damaging the power outlet and the plug Close the power outlet lid when not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit. Do not use plug adaptors to connect too many plugs to the power outlet. After inserting a plug, gently close the power outlet lid.
Page 351 If the power outlet is loose when an electrical appliance plug is con- nected Replace the outlet. Contact a Toyota dealer for any necessary replacements. If the power outlet gets dirty Turn the main switch off and use a soft, clean cloth to wipe it gently.
Page 352: Seatback Table
3-6. Other interior features ∗ Seatback table Front passenger’s seatback can be used as a temporary table only when the vehicle is stopped. Fold down the front passen- ger’s seat to use the seatback table. (→P. 47) CAUTION Caution while driving Observe the following precautions to avoid death or serious injury.
Page 353: Floor Mat
When installing the driver’s floor mat Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. Only use floor mats designed for the driver’s seat. Always install the floor mat securely using the retaining hooks (clips) pro- vided.
Page 354 3-6. Other interior features CAUTION Before driving Check that the floor mat is securely fixed in the right place with all the pro- vided retaining hooks (clips). Be espe- cially careful to perform this check after cleaning the floor. With the engine stopped and the shift lever in P (automatic transmission) or N (manual transmission), fully depress each pedal to the floor to make sure it...
Page 355: Luggage Compartment Features
3-6. Other interior features Luggage compartment features Behind the rear seat (Double Cab models only) Cargo net hooks (vehicles with sub woofer) Grocery bag hooks Flashlight holder Storage boxes Deck Auxiliary boxes Tie-down cleats Deck hooks I n f o r ma t i o n P r o v i d e d b y :...
Page 356 3-6. Other interior features Auxiliary boxes Left side Turn the knob counterclock- wise. Open the lid. Right side (vehicles without 115V power outlet) Turn the knob counterclock- wise. Open the lid. Right side (vehicles with 115V power outlet) Turn the knob counterclock- wise.
Page 357 3-6. Other interior features CAUTION Caution while driving Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking. Deck hooks Deck hooks are provided for securing loose items. CAUTION When not in use Keep the deck hooks folded.
Page 358 3-6. Other interior features Tie-down cleats The deck rail system enables you to insert and move tie-down cleats to their best location along deck rails to secure a load. Locking plate Thumb wheel Tie-down cleat Installing the tie-down cleat Loosen the thumb wheel in a counterclockwise motion, and depress the wheel so that the locking plate maintains 0.5 in.
Page 359 3-6. Other interior features Insert the locking plate into the deck rail, rotate the tie-down cleat 90°, and release the thumb wheel. Slide the cleat to the closest detent in the rail system. You will feel that the locking plate snaps into a detent.
Page 360 3-6. Other interior features CAUTION Tie-down cleat precautions Properly install and tighten the tie-down cleats into the deck rail system. Failure to properly install and tighten the tie-down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehi- cle is in motion.
Page 361 3-6. Other interior features Left side Removing the separator Remove the separator. It can be installed in various positions as required. Flashlight holder (Double Cab models only) Flashlight holder is designed to hold the flashlight securely. I n f o r ma t i o n P r o v i d e d b y :...
Page 362 3-6. Other interior features Removing the flashlight holder Remove the flashlight holder. It can be installed in various positions as required. Grocery bag hooks (Double Cab models only) Grocery bag hook is designed to hang things like grocery bag. NOTICE Grocery bag hook weight capacity Do not hang any object heavier than 7 lb.
Page 363 3-6. Other interior features Cargo net hooks (Double Cab models with sub woofer) Cargo net hooks are designed to hang the factory-supplied cargo net. NOTICE To prevent damage to the cargo net hook Do not hang items other than the cargo net. I n f o r ma t i o n P r o v i d e d b y :...
Page 364: Garage Door Opener Box
3-6. Other interior features ∗ Garage door opener box The garage door opener box is designed to store a garage door opener transmitter. Storing the transmitter in the box Pull the lid down while pushing the knob. Remove the hook-and-loop fastener square.
Page 365 3-6. Other interior features Remove the paper strip covering the adhesive on back side of square. Adhere the square to back side of the transmitter near the center. Place the transmitter with fas- tener square facing inside of box into the box. Make sure the transmitter but- ton is located above button pins.
Page 366 3-6. Other interior features Operating the garage door opener transmitter When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the button of the cover. Push the button. If a garage door opener transmitter has wire clip for sun visor This clip must be removed prior to adhe- sion of the fastener.
Page 367 3-6. Other interior features CAUTION Caution while driving Keep the garage door opener box closed. Injuries may result in the event of an accident or sudden braking. To prevent an accident Keep the remaining spacers away from the children. I n f o r ma t i o n P r o v i d e d b y :...
Page 368: Compass (Vehicles With Accessory Meter)
3-6. Other interior features Compass (vehicles with accessory meter) The compass on the accessory meter indicates the direction in which the vehicle is heading. Operation To turn the compass on or off, press the switch. Displays and directions Display Direction North Northeast East...
Page 369 3-6. Other interior features Calibrating the compass Samoa: 5 Guam: 8 Saipan: 8 The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
Page 370 3-6. Other interior features Circling calibration Stop the vehicle where it is safe to drive in a circle. Press the switch until CAL appears on the display. At this time, the compass display is locked in N. Drive the vehicle at 5 mph (8 km/ h) or less in a circle until the direction is displayed.
Page 371 3-6. Other interior features Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions: The vehicle is stopped immediately after turning. The compass does not adjust while the vehicle is stopped. The engine switch is turned off immediately after turning. The vehicle is on an inclined surface.
Page 372 3-6. Other interior features NOTICE To avoid the compass malfunctions Do not place magnets or any metal objects on or near the roof. Doing this may cause a malfunction of the compass sensor. To ensure normal operation of the compass Do not perform circling calibration of the compass in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields.
Page 373 3-6. Other interior features I n f o r ma t i o n P r o v i d e d b y :...
Page 374: Maintenance And Care
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. l Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 375: Maintenance And Care
4-1. Maintenance and care Bumpers and side moldings Do not scrub with abrasive cleaners. CAUTION Caution about the exhaust pipe Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.
Page 376 4-1. Maintenance and care NOTICE Clean the drainage hole of the deck regularly. If the drainage hole is stopped up, the water will not be able to flow, and it will cause rust. Cleaning the exterior lights Wash carefully. Do not use organic substances or scrub with a hard brush. This may damage the surfaces of the lights.
Page 377: Cleaning And Protecting The Vehicle Interior
Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. I n f o r ma t i o n P r o v i d e d b y :...
Page 378 4-1. Maintenance and care Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained when keeping the carpet as dry as possible.
Page 379 4-1. Maintenance and care NOTICE Cleaning detergents Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. Do not use polish wax or polish cleaner.
Page 380: Maintenance
Warranty Information Booklet”, “Owner’s Manual Supplement”. Repair and replacement It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 381 4-2. Maintenance Allow inspection and repairs to be performed by a Toyota dealer Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
Page 382: General Maintenance
“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
Page 383 4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be hold securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 384 4-2. Maintenance Items Check points • Moves smoothly? Steering wheel • Has correct free play? • No strange noises? Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? •...
Page 385: Emission Inspection And Maintenance (I/M) Programs
The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. Your vehicle may not pass the I/M test:...
Page 386: Do-It-Yourself Maintenance
• FMVSS No.116 DOT 3 or SAE Brake fluid level (→P. 380) J1703 brake fluid • Rag or paper towel • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 387 4-3. Do-it-yourself maintenance Items Parts and tools • Bulb with same number and watt- age rating as original Light bulbs (→P. 418) • Phillips-head screwdriver • Conventional wrench • Automatic transmission fluid Power steering fluid level ® DEXRON II or III (→P.
Page 388 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. When working on the engine compartment Keep hands, clothing, and tools away from the moving fan and engine drive belt.
Page 389 4-3. Do-it-yourself maintenance NOTICE If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment. If the fluid level is low or high It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high.
Page 390: Hood
4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. The hood will pop up slightly. Pull up the hood catch lever and lift the hood. I n f o r ma t i o n P r o v i d e d b y :...
Page 391 4-3. Do-it-yourself maintenance Hold the hood open by insert- ing the supporting rod into the slot. CAUTION Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
Page 392: Engine Compartment
4-3. Do-it-yourself maintenance Engine compartment 2.7 L 4-cylinder (2TR-FE) engine Washer fluid tank (→P. 386) Engine oil level dipstick (→P. 374) Radiator cap Brake fluid reservoir Engine coolant reservoir (→P. 380) (→P. 379) Fuse box (→P. 408) Engine oil filler cap (→P.
Page 393 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Washer fluid tank (→P. 386) Engine oil filler cap (→P. 375) Power steering fluid reservoir (→P. 382) Brake fluid reservoir (→P. 380) Radiator cap Fuse box (→P. 408) Engine oil level dipstick (→P.
Page 394 4-3. Do-it-yourself maintenance Engine oil Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil Park the vehicle on level ground. After turning off the engine, wait more than 5 minutes for the oil to drain back into the bot- tom of the engine.
Page 395 4-3. Do-it-yourself maintenance 2.7 L 4-cylinder (2TR-FE) engine Full 4.0 L V6 (1GR-FE) engine Full Adding engine oil 2.7 L 4-cylinder (2TR-FE) engine If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Page 396 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Make sure to check the oil type and prepare the items needed before adding oil. →P. 492 Engine oil selection Items Clean funnel Remove the oil filler cap, turning it counterclockwise. Add engine oil slowly. Checking the dipstick.
Page 397 1000 km) If you consume more than 1.1 qt. (1.0 L, 0.9 lmp.qt.) every 600 miles (1000 km), contact your Toyota dealer. After changing the engine oil (U.S.A. only) The oil change system should be reset. Perform the following procedures: Turn the engine switch off with the odometer reading shown.
Page 398 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 399 If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system. Coolant selection Only use “Toyota Super Long Life Coolant”...
Page 400 Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION When the engine is hot Do not touch the radiator or condenser as they may be hot and may cause burns.
Page 401 4-3. Do-it-yourself maintenance Type B Adding fluid Make sure to check the fluid type and prepare the necessary items. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Rag or paper towel Type B only Turn the engine switch off. Depress the brake pedal 20 times or more.
Page 402 4-3. Do-it-yourself maintenance CAUTION When filling the reservoir Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.
Page 403 4-3. Do-it-yourself maintenance Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures. (Fluid temperature, 104°F - 175°F [40°C - 80°C]) Cold: Engine has not been run for about 5 hours. (Room tem- perature, 32°F - 104°F [0°C - 40°C]) 4.0 L V6 (1GR-FE) engine Full (when cold)
Page 404 4-3. Do-it-yourself maintenance CAUTION Checking the fluid level Take care, as the reservoir may be hot. NOTICE When adding fluid Avoid overfilling, or the power steering may be damaged. After replacing the reservoir cap Check the steering box case, vane pump and hose connections for leaks or damage.
Page 405 4-3. Do-it-yourself maintenance Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable. Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
Page 406 4-3. Do-it-yourself maintenance CAUTION Emergency measures regarding electrolyte If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
Page 407 4-3. Do-it-yourself maintenance Add washer fluid. CAUTION When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE Do not use any fluid other than washer fluid Do not use soapy water or engine antifreeze instead of washer fluid.
Page 408: Tires
The tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 444) I n f o r ma t i o n P r o v i d e d b y :...
Page 409 Have tire pressure warning valve and trans- mitter ID codes registered by your Toyota dealer. (→P. 390) Initializing the tire pressure warning system The tire pressure warning system must be initialized in the fol-...
Page 410 ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 411 A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
Page 412 4-3. Do-it-yourself maintenance Access Cab models Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 413 If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. When operating the tire pressure warning reset switch, the tire pres- sure warning light does not flash 3 times.
Page 414 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. Do not use tire sizes other than those recommended by Toyota. Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 415 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 416: Tire Inflation Pressure
4-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 500) Regular Cab and Double Cab models I n f o r ma t i o n P r o v i d e d b y :...
Page 417 4-3. Do-it-yourself maintenance Access Cab models I n f o r ma t i o n P r o v i d e d b y :...
Page 418 4-3. Do-it-yourself maintenance Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.
Page 419 Reduced driving comfort and tire life Reduced safety Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: Check only when the tires are cold.
Page 420 4-3. Do-it-yourself maintenance CAUTION Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. Excessive wear Uneven wear Poor handling Possibility of blowouts resulting from overheated tires Poor sealing of the tire bead Wheel deformation and/or tire separation A greater possibility of tire damage from road hazards...
Page 421: Wheels
Used wheels l Bent wheels that have been straightened Wheel precautions l Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels. l When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).
Page 422 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 423: Air Conditioning Filter
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method Turn the engine switch off. Open the glove box. Slide off the damper. Push in each side of the glove box to disconnect the claws.
Page 424 4-3. Do-it-yourself maintenance Open the filter door. Remove the filter. Replacement method Remove the air conditioning filter and replace it with a new one. When installing the filter, follow the instructions indicated on the label. I n f o r ma t i o n P r o v i d e d b y :...
Page 425 4-3. Do-it-yourself maintenance Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) If air flow from the vents decreases dramatically The filter may be clogged.
Page 426: Wireless Remote Control Battery
4-3. Do-it-yourself maintenance ∗ Wireless remote control battery Replace the battery with a new one if it is discharged. You will need the following items: Lithium battery CR2032 Replacing the battery Remove the cover using a coin protected with tape etc. Remove the discharged trans- mitter battery.
Page 427 The wireless remote control will not function properly. The operational range is reduced. Use a CR2032 lithium battery Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. Replace only with the same or equivalent type recommended by your Toyota dealer.
Page 428: Checking And Replacing Fuses
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch off. The fuses are located in the following places. To check the fuses, follow the instructions below.
Page 429 4-3. Do-it-yourself maintenance After a system failure, see “Fuse layout and amperage rat- ings” (→P. 411) for details about which fuse to check. Remove the fuse with the pull- out tool. Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 430 4-3. Do-it-yourself maintenance Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type C Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 431 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings Engine compartment Type A Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 432 4-3. Do-it-yourself maintenance Fuse Ampere Circuit 10 A Air conditioning system FR FOG 15 A Front fog lights TOWING TAIL 30 A Trailer lights (tail lights) Stop lights, high mounted stop- light, vehicle stability control sys- tem, anti-lock brake system, shift STOP 10 A lock system, multiport fuel injection...
Page 433 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiport fuel injection system/ 20 A sequential multiport fuel injection system HORN 10 A Horn Multiport fuel injection system/ A/F HEATER 15 A sequential multiport fuel injection system Wireless remote control system, air conditioning system, multiplex ECU-B 7.5 A communication system, meter and...
Page 434 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiport fuel injection system/ A/PUMP 50 A sequential multiport fuel injection system Anti-lock brake system, vehicle sta- ABS NO.2 30 A bility control system AC SKT 100 A Cigarette lighter, power outlets AM1, AC SKT, HEATER, FR FOG, 120 A* STOP, OBD, J/B, TOWING TAIL, TOWING BRK and BATT CHG...
Page 435 4-3. Do-it-yourself maintenance Under the instrument panel Fuse Ampere Circuit Multiport fuel injection system/ sequential multiport fuel injection system, anti-lock brake system, 15 A traction control system, vehicle sta- bility control system, SRS airbag system, front passenger occupant classification system Meter and gauge, emergency GAUGE 7.5 A...
Page 436 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Anti-lock brake system, vehicle sta- bility control system, stop lights, charging system, multiport fuel injection system/sequential multi- port fuel injection system, air condi- IG1 NO.2 10 A tioning system, instrument panel light control, anti-glare inside rear view mirror, back monitor, clutch start cancel switch, rear differential lock system, power outlets, tire...
Page 437 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix.
Page 438: Light Bulbs
You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 439 4-3. Do-it-yourself maintenance Rear bulb locations High mounted stoplight Rear turn signal lights Back-up lights License plate lights Replacing light bulbs Headlights Unplug the connector. I n f o r ma t i o n P r o v i d e d b y :...
Page 440 4-3. Do-it-yourself maintenance Remove the rubber cover. Release bulb retaining spring. Remove the bulb. To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole. I n f o r ma t i o n P r o v i d e d b y :...
Page 441 4-3. Do-it-yourself maintenance Front fog lights (if equipped) Unplug the connector while pull- ing the lock release. Turn the bulb counterclockwise. I n f o r ma t i o n P r o v i d e d b y :...
Page 442 4-3. Do-it-yourself maintenance Parking and front side marker lights Turn the bulb base counterclock- wise. Remove the light bulb. I n f o r ma t i o n P r o v i d e d b y :...
Page 443 4-3. Do-it-yourself maintenance Front turn signal lights/daytime running lights (if equipped) Turn the bulb base counterclock- wise. Remove the light bulb. I n f o r ma t i o n P r o v i d e d b y :...
Page 444 4-3. Do-it-yourself maintenance Back-up lights and rear turn signal lights Remove the bolts and rear com- bination assembly. Unplug connector while depressing the lock release. Turn the bulb bases counter- clockwise. Rear turn signal light Back-up light Remove the light bulb. Rear turn signal light Back-up light I n f o r ma t i o n P r o v i d e d b y :...
Page 445 4-3. Do-it-yourself maintenance High mounted stoplight Remove the screws and cover. Remove the light bulbs. I n f o r ma t i o n P r o v i d e d b y :...
Page 446 4-3. Do-it-yourself maintenance License plate lights Remove the screw and light unit. Turn the bulb base counterclock- wise. Remove the light bulb. I n f o r ma t i o n P r o v i d e d b y :...
Page 447 LED light bulbs The stop/tail and rear side marker lights consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. If two or more LEDs in a stop light burn out, your vehicle may not conform to local laws (SAE).
Page 448 4-3. Do-it-yourself maintenance I n f o r ma t i o n P r o v i d e d b y :...
Page 449: Essential Information
5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE To prevent battery discharge Do not leave the emergency flashers on longer than necessary when the engine is not running.
Page 450: If Your Vehicle Needs To Be Towed
If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 451 5-1. Essential information Vehicles with off-road package Towing hook Emergency towing procedure The engine switch must be in the ACC (engine off) or the ON (engine running) position. 4WD models: Put the front-wheel drive control switch in H2. Put the shift lever in N. Release the parking brake.
Page 452 5-1. Essential information NOTICE Emergency towing eyelet/hook precautions Before emergency towing, check that the eyelet/hook is not broken or damaged. Fasten the towing cable or chain securely to the eyelet/hook. Do not jerk the eyelet/hook. Apply steady and even force. To avoid damaging the eyelet/hook, do not pull from the side or at a verti- cal angle.
Page 453 5-1. Essential information Towing with a wheel lift-type truck from the front Vehicles with an automatic trans- mission: Use a towing dolly under the rear wheels. 2WD models with a manual transmission: We recommend to use a towing dolly under the rear wheels.
Page 454 5-1. Essential information Towing with a wheel lift-type truck from the rear 2WD models Turn the engine switch to the ACC position. 4WD models We recommend to use a towing dolly under the front wheels. When not using a towing dolly, turn the engine switch to the ACC position, shift the shift lever to N and put the front-wheel drive con-...
Page 455 5-1. Essential information Using a flat bed truck If your Toyota is transported by a Front flat bed truck, it should be tied down at the locations shown in the illustration. If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°.
Page 456: If You Think Something Is Wrong
5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms l Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 457: Fuel Pump Shut Off System
5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 458: Event Data Recorder
5-1. Essential information Event data recorder Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.
Page 459 5-1. Essential information Disclosure of the data Toyota will not disclose the data recorded in an EDR to a third party except when: l An agreement from the vehicle’s owner (or the leasing company for a leased vehicle) is obtained...
Page 460: Steps To Take In An Emergency If A Warning Light Turns On Or A Warning Buzzer Sounds
Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer)* •...
Page 461 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: (U.S.A.)
Page 462 5-2. Steps to take in an emergency Warning light Warning light/Details SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; • The passenger airbag off switch (Access Cab mod- els); or •...
Page 463 • When the light stays on Have the system after blinking for 1 checked by your minute: Malfunction in Toyota dealer. the tire pressure warning system. Low fuel level warning light Refuel the vehicle. Low level of fuel.
Page 464 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Engine oil replacement reminder light • Illuminates for about 3 Check the engine oil, seconds and then flashes and change if neces- for about 12 seconds: Indi- sary.
Page 465 5-2. Steps to take in an emergency The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible. Front passenger detection sensor and passenger seat belt reminder If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light to flash and buzzer to sound.
Page 466 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.)
Page 467 Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota dealer. Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes.
Page 468 5-2. Steps to take in an emergency CAUTION Maintenance of the tire Please note that the TPMS (tire pressure warning system) is not a sub- stitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale (tire pressure warning light).
Page 469: If You Have A Flat Tire
5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. Before jacking up the vehicle l Stop the vehicle on a hard, flat surface. l Set the parking brake. l Shift the shift lever to P (automatic transmission) or R (manual transmission).
Page 470 5-2. Steps to take in an emergency Access Cab models Tool bag Jack Double Cab models Tool bag Jack Taking out the jack and tool bag Regular Cab models with bench type seat Pull the lever and fold down the seatback.
Page 471 5-2. Steps to take in an emergency Regular Cab models with separated type seat Pull the lever and fold down the seatback. Unhook the strap and remove the tool bag. Loosen and remove the jack. Loosen Tighten I n f o r ma t i o n P r o v i d e d b y :...
Page 472 5-2. Steps to take in an emergency Access Cab models Pull up the lever Raise the bottom cushion up. Turn the knob counterclockwise. Open the lid. Press the lid against the bot- tom of the lower cushion until it is supported by the hook- and-loop fastener.
Page 473 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Double Cab models Swing the bottom cushion up by pulling the lock release strap. Turn the knob counterclock- wise. Open the lid. Unhook the strap and remove the tool bag.
Page 474 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Assemble the jack handle (in the tool bag) Type A Assemble the jack handle exten- sion as shown. Be sure to tighten each screw securely. Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 475 5-2. Steps to take in an emergency Taking out the spare tire Type A Insert the end of the jack handle extension into lowering screw and turn it counterclock- wise. After the tire is lowered com- pletely to the ground, remove the holding bracket.
Page 476 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Wheel Flat tire chock positions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of Left- the front...
Page 477 5-2. Steps to take in an emergency Remove the wheel ornament using the wheel nut wrench as shown. To protect the wheel and wheel ornament, place a rag between the wrench and the wheel ornament, as shown in the illustration. Type A Type B Type C...
Page 478 5-2. Steps to take in an emergency Slightly loosen the wheel nuts (one turn). Assemble the jack handle extension as shown. Type A Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 479 5-2. Steps to take in an emergency Position the jack at the correct jack point as shown. Front Rear Make sure the jack is positioned on a level and solid place. Front Raise the vehicle until the tire is slightly raised off the ground. When positioning the jack under the rear axle housing, make sure the groove on the top of...
Page 480 5-2. Steps to take in an emergency Installing the tire Remove any dirt or foreign mat- ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
Page 481 5-2. Steps to take in an emergency Replacing an aluminum wheel with an aluminum wheel Tighten the nuts until the washer Washer of the nut comes into loose con- tact with the disc wheel. Disc wheel Lower the vehicle. Firmly tighten each nut two or three times in the order shown in the illustration.
Page 482 5-2. Steps to take in an emergency 4WD models and PreRunner Stowing the flat tire, jack and all tools Lay down the tire with the outer side facing up, and install the holding bracket. Then secure the tire, taking care that the tire goes straight up without catching on any other part, to prevent it from flying for- ward during a collision or sudden braking.
Page 483 5-2. Steps to take in an emergency CAUTION Using the jack Improper use of the jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. Do not use the jack for any purpose other than replacing tires or install- ing and removing tire chains.
Page 484 5-2. Steps to take in an emergency CAUTION Replacing a flat tire Never use oil or grease on the wheel bolts or wheel nuts. Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing a serious accident.
Page 485 5-2. Steps to take in an emergency CAUTION When the spare tire is attached The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: ABS & Brake assist TRAC Active traction control system (if equipped) Hill-start assist control system (if equipped) Downhill assist control system (if equipped) AUTO LSD system...
Page 486 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 487: If The Engine Will Not Start
One or both of the battery terminals may be disconnected. l The battery may be discharged. (→P. 471) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. I n f o r ma t i o n P r o v i d e d b y :...
Page 488: If The Shift Lever Cannot Be Shifted From P
(a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 489: If You Lose Your Keys
5-2. Steps to take in an emergency If you lose your keys New genuine Toyota keys can be made by your Toyota dealer using the key number stamped on your key number plate. Vehicles with engine immobilizer system, the dealer will also need the master key.
Page 490: If The Vehicle Battery Is Discharged
You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. Connect the jumper cables.
Page 491 Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible. I n f o r ma t i o n P r o v i d e d b y :...
Page 492 5-2. Steps to take in an emergency Starting the engine when the battery is discharged (vehicles with an automatic transmission) The engine cannot be started by push-starting. Avoiding a discharged battery Turn off the headlights and the audio system while the engine is turned off.
Page 493 5-2. Steps to take in an emergency CAUTION Battery precautions Always wash your hands after handling the battery support, terminals, and other battery-related parts. Do not allow children near the battery. NOTICE To prevent damaging the vehicle (vehicles with a manual transmission) Do not pull- or push-start the vehicle, because the three-way catalytic con- verter may overheat and become a fire hazard.
Page 494: If Your Vehicle Overheats
If the fan is not operating: Stop the engine immediately and call your local Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 495 (→P. 495) Have the vehicle checked at your nearest Toyota dealer as soon as possible. I n f o r ma t i o n P r o v i d e d b y :...
Page 496 5-2. Steps to take in an emergency Overheating If you observe the following, your vehicle may be overheating. The engine coolant temperature gauge enters the red zone or a loss of power is experienced. Steam is coming from under the hood. CAUTION To prevent an accident or injury when inspecting under the hood of your vehicle...
Page 497: If The Vehicle Becomes Stuck
5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. Stop the engine. Set the parking brake and put the shift lever in P (vehicles with an automatic transmission) or N (vehicles with a manual transmission).
Page 498 5-2. Steps to take in an emergency NOTICE To avoid damaging the transmission and other components Avoid spinning the wheels and do not rev the engine. If the vehicle remains stuck after trying these procedures, the vehicle may require towing to be freed. I n f o r ma t i o n P r o v i d e d b y :...
Page 499: If Your Vehicle Has To Be Stopped In An Emergency
5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmly depress it.
Page 500 5-2. Steps to take in an emergency CAUTION If the engine has to be turned off while driving Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 501 5-2. Steps to take in an emergency I n f o r ma t i o n P r o v i d e d b y :...
Page 502: Specifications Maintenance Data (Fuel, Oil Level, Etc.)
6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions 2WD models except PreRunner Access Cab Cab type Regular Cab Double Cab Except X-Runner X-Runner Overall 190.4 in. 208.1 in. (5285 mm) length (4835 mm) Overall 74.0 in. 74.6 in. 72.2 in. (1835 mm) width (1880 mm) (1895 mm)
Page 503 : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your Toyota dealer about the weight of accessory parts. I n f o r ma t i o n P r o v i d e d b y :...
Page 504 (1GR-FE) engine Long deck : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your Toyota dealer about the weight of accessory parts. 4WD models Vehicle capacity Cab type Engine...
Page 505 6-1. Specifications TWR (Trailer Weight Rating) Regular Cab models Driving Model code Engine system TRN220L-TRMDKA TRN220L-TRPDKA 2.7 L 4-cylinder 3500 lb. (1587 kg) (2TR-FE) engine TRN240L-TRMDKA TRN240L-TRPDKA Access Cab models Driving Model code Engine system TRN225L-CRMDKA TRN225L-CRPDKA 2.7 L 4-cylinder TRN245L-CRMDKA 3500 lb.
Page 506 6-1. Specifications Double Cab models Driving Model code Engine system TRN225L-PRPDKA 3400 lb. (1542 kg) 2.7 L 4-cylinder (2TR-FE) engine TRN265L-PRPDKA 3500 lb. (1587 kg) 3500 lb. (1587 kg) GRN245L-PRADKA 6400 lb. (2903 kg) 3500 lb. (1587 kg) GRN245L-PRFDKA 6400 lb. (2903 kg) 3500 lb.
Page 507 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 508 6-1. Specifications Engine number The engine number is stamped on the engine block as shown. 2.7 L 4-cylinder (2TR-FE) engine 4.0 L V6 (1GR-FE) engine I n f o r ma t i o n P r o v i d e d b y :...
Page 509 6-1. Specifications Engine 2.7 L 4-cylinder (2TR-FE) engine Model 2TR-FE Type 4-cylinder in line, 4-cycle, gasoline 3.74 × 3.74 in. (95.0 × 95.0 mm) Bore and stroke Displacement 164.3 cu.in. (2694 cm Drive belt tension Automatic adjustment Valve clearance (engine cold) 　Intake Automatic adjustment 　Exhaust...
Page 510 -reference) 5.4 qt. (5.1 L, 4.5 Imp.qt.) Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC multigrade engine oil...
Page 511 6-1. Specifications How to read oil container label: The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use. 4.0 L V6 (1GR-FE) engine Oil capacity (Drain and refill -reference) 2WD models except...
Page 512 6-1. Specifications Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC multigrade engine oil Recommended viscosity: SAE 5W-30...
Page 513 10.1 qt. (9.6 L, 8.4 Imp.qt.) Vehicles with a manual transmission 10.3 qt. (9.7 L, 8.5 Imp.qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 514 4WD models and PreRunner 3.12 qt. (2.95 L, 2.60 Imp.qt.) Toyota Genuine Differential Gear Oil LT 75W-85 GL-5 or equivalent Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the Oil type and viscosity factory. Use Toyota approved “Toyota Genuine Differential Gear Oil”...
Page 515 : The fluid capacity is the quantity of reference. If replacement is necessary, contact your Toyota dealer. NOTICE Automatic transmission fluid type (4-speed models) Using automatic transmission fluid other than “Toyota Genuine ATF Type T- IV” may cause deterioration in shift quality, locking up of your transmission accompanied vibration,...
Page 516 6-1. Specifications Manual transmission Gear oil capacity (Reference) 2.7 L 4-cylinder (2TR-FE) engine 2WD models 2.7 qt. (2.6 L, 2.3 Imp.qt.) 4WD models 2.3 qt. (2.2 L, 1.9 Imp.qt.) 4.0 L V6 (1GR-FE) engine 1.9 qt. (1.8 L, 1.6 Imp.qt.) Gear oil type Gear oil API GL-4 or GL-5 Recommended gear oil viscosity...
Page 517 6-1. Specifications Brakes Pedal clearance 2WD models except 4.3 in. (110 mm) PreRunner PreRunner 4.2 in. (106 mm) 4WD models Without off-road package 4.2 in. (106 mm) With off-road package 3.4 in. (88 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) Pedal free play Brake pad wear limit 0.04 in.
Page 518 6-1. Specifications Steering Free play Less than 1.2 in. (30 mm) ® Automatic transmission fluid DEXRON II or Power steering fluid type Tires and wheels Type A Tire size P215/70R15 97S Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Rear tires: 33 psi (230 kPa, 2.3 kgf/cm or bar)
Page 519 6-1. Specifications Type B Tire size P245/75R16 109S Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Rear tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Spare tire: Tire inflation pressure 30 psi (210 kPa, 2.1 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 520 6-1. Specifications Type D Tire size P265/65R17 110S Front tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Rear tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Spare tire: Tire inflation pressure 29 psi (200 kPa, 2.0 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 521 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights — 60/55 Front fog lights 9145 Parking and front side — marker lights Front turn signal lights 4157 and daytime running 27/8 Exterior lights Rear turn signal lights 3157A 27/8 Back-up lights License plate lights High mounted...
Page 522: Fuel Information
ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. If your engine knocks Consult your Toyota dealer.
Page 523 Toyota allows the use of oxygenate blended gasoline where the oxygenate content is up to 10% ethanol or 15% MTBE. If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87. Toyota does not recommend the use of gasoline containing methanol.
Page 524 6-1. Specifications NOTICE Notice on fuel quality Do not use improper fuels. If improper fuels are used the engine will be damaged. Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction. Do not use gasohol other than that stated here.
Page 525: Tire Information
6-1. Specifications Tire information Typical tire symbols Tire size (→P. 509) DOT and Tire Identification Number (TIN) (→P. 508) Location of treadwear indicators (→P. 388) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Page 526 6-1. Specifications Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. Summer tire or all season tire (→P. 392) An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.
Page 527 6-1. Specifications Tire size Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol...
Page 528 U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 529 6-1. Specifications Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
Page 530 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Glossary of tire terminology Tire related term Meaning...
Page 531 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as Occupant distribution specified in the third column of Table 1 below The combined weight of installed regular production options weighing over 5 lb.
Page 532 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 533 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on Intended outboard the other sidewall of the tire, or sidewall...
Page 534 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between Ply separation adjacent plies A mechanical device made of rubber, chemicals, fabric and steel or other materials, Pneumatic tire that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that...
Page 535 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear designed to give a visual indication of the...
Page 536: Customization
Programming these preferences requires specialized equipment and may be performed by an autho- rized Toyota dealership. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customized Item Function...
Page 537: Items To Initialize
6-2. Customization Items to initialize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item When to initialize Reference Engine oil maintenance After changing engine oil P.
Page 538 6-2. Customization I n f o r ma t i o n P r o v i d e d b y :...
Page 539: Reporting Safety Defects For U.s. Owners
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 540: Seat Belt Instructions For Canadian Owners (In French)
Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. I n f o r ma t i o n P r o v i d e d b y :...
Page 541 I n f o r ma t i o n P r o v i d e d b y :...
Page 542: Camper Information
National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchas- ers and/or prospective purchasers of Toyota vehicles with infor- mation on truck-camper loading. Your Toyota dealer will help answer any questions you may have as you read this informa- tion.
Page 543 CAUTION Loading precaution If a load is too far back, it can cause dangerous handling. If it is too far forward, the front axle may be overloaded. Cargo weight rating and proper matching When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the manufacturer’s camper weight figure, the weight of installed additional camper equipment not included in the manufacturer’s camper weight figure, the weight of camper cargo,...
Page 544 Access Cab models 2 people, 2TR-FE engine, 2WD except PreRunner: 900 lb. (408 kg) 4 people, 2TR-FE engine, 2WD except PreRunner: 600 lb. (272 kg) 2 people, 2TR-FE engine, PreRunner: 1000 lb. (453 kg) 4 people, 2TR-FE engine, PreRunner: 700 lb. (317 kg) 2 people, 1GR-FE engine, PreRunner: 1000 lb.
Page 545 Gross axle and vehicle weight ratings Secure loose items to prevent weight shifts that could affect the bal- ance of your vehicle. When the truck camper is loaded, drive to a scale and weigh on the front and on the rear wheels separately to determine axle loads.
Page 546 GAWR GAWR Front Rear 2WD models except PreRun- 2380 lb. (1079 kg) 2685 lb. (1217 kg) Regular Cab models 3000 lb. (1360 kg) 4WD models and 2755 lb. (1249 kg) Access Cab and PreRunner Double Cab models 3110 lb. (1410 kg) GVWR 2WD models except PreRunner Cab type...
Page 547 PreRunner Cab type GVWR Access Cab 5250 lb. (2381 kg) Vehicles with 2.7 L 4-cylinder (2TR-FE) engine 5250 lb. (2381 kg) Double Cab Vehicles with 4.0 L V6 (1GR-FE) engine 5350 lb. (2426 kg) 4WD models Cab type GVWR Regular Cab 5100 lb.
Page 548: Alphabetical Index
Alphabetical index Alphabetical index A/C..........236 Audio system ABS ...........192 Antenna......... 249 Access doors ......39 Audio input ......271 Accessory meter ......164 AUX port ....... 271 Active traction control CD player ......253 system ........182 MP3/WMA disc ..... 259 Air conditioning filter....403 Optimal use......
Page 549 Alphabetical index Brakes Child safety Brake system warning buzzer Airbag precautions ....90 ... 183, 185, 190, 195, 441 Battery precautions ..385, 473 Brake system warning light .. 441 Child restraint system....106 Fluid........380 Child-protectors.......37 Parking brake ....... 154 How your child should wear Break-in tips ......
Page 550 Alphabetical index Daytime running light Emergency, in case of system ........166 Blown fuse ......408 Deck If the engine will not start ..468 Auxiliary boxes ......335 If the shift lever cannot be Deck hooks ......336 shifted from P ..... 469 Deck rails ......203 If the vehicle battery is Deck ........334...
Page 551 Alphabetical index Engine coolant temperature Front turn signal lights gauge ........157 Lever ........153 Engine immobilizer system..78 Replacing light bulbs .....423 Engine oil Switch........153 Capacity ....... 492 Wattage.........503 Checking ......374 Fuel Preparing and checking before Capacity ........491 winter ......... 210 Fuel gauge ......157 Warning light ....
Page 552 Alphabetical index Hands-free system Jack (for cellular phone) ....276 Positioning the jack ....457 Hazard lights Vehicle-equipped jack... 450 Switch........430 Jack handle ......455 Head restraints Adjusting ........54 Keyless entry ......32 Headlights Keys Replacing light bulbs .....419 Engine switch......144 Switch........165 If you lose your keys .....
Page 553 Alphabetical index Limited slip differential... 184 Odometer ........158 Load capacity ..203, 208, 485 Off-road precautions Lock steering column ....64 Driving ........200 Luggage storage box....339 Vehicle ........198 Luggage compartment features........334 Engine oil ......374 Warning light ....442, 444 Opener Maintenance Fuel door .........74...
Page 554 Alphabetical index Radiator ......372, 380 Seat belts Radio .........247 Adjustment ......58 Rear seat ALR .........60 Adjustment ......50 Automatic Locking Folding down......51 Retractor.......60 Raising the bottom Child restraint system cushion .........50 installation......111 Rear side marker lights Cleaning and maintaining ..358 Replacing light bulbs .....427 ELR .........60 Switch........165...
Page 555 Alphabetical index Seatback table ......331 Storage feature......310 Service reminder Storage precautions ....206 indicators ......160 Stuck Shift lever If the vehicle becomes Automatic transmission ..147 stuck ........478 Four-wheel drive....178 Sun visors.........319 If the shift lever cannot be Switch shifted from P.....
Page 556 Alphabetical index Tachometer.......157 Traction control ....... 192 Tailgate TRAC......... 192 Removing the tailgate .....40 Trip meter ......... 158 Tailgate ........40 Turn signal lights Tail lights Lever ........153 Replacing light bulbs .....427 Replacing light Switch........165 bulbs ......423, 424 Talk switch........281 Switch ........
Page 557 Alphabetical index Seat belt ....... 444 Seat belt pretensioner system........ 442 SRS ........442 SRS airbag system....442 Tire pressure ......444 Tire pressure warning system........ 444 VSC/TRAC ......442 Washer Checking ......386 Preparing and checking before winter ...... 210 Switch........
Page 558: What To Do If
What to do if... What to do if... A tire punctures If you have a flat tire P. 450 P. 468 If the engine will not start The engine does not start P. 78 Engine immobilizer system P. 471 If the vehicle battery is discharged If the shift lever cannot be shifted The shift lever cannot be P.
Page 559 What to do if... Instrument cluster Center panel I n f o r ma t i o n P r o v i d e d b y :...
Page 560 What to do if... nWarning lights Brake system warning SRS warning light light P. 443 Automatic transmission fluid temperature P. 441 P. 443 warning light Slip indicator* Charging system warning light P. 442 P. 443 Tire pressure warning Low engine oil pressure light warning light P.
Page 561 Memo I n f o r ma t i o n P r o v i d e d b y :...
Page 562: Gas Station Information
Cold tire inflation P. 500 pressure Engine oil capacity (Drain and refill P. 492 -reference) Toyota Genuine Motor Oil or equivalent Oil grade: P. 492 ILSAC multigrade engine oil Engine oil type Recommended oil viscosity: SAE 0W-20 (2.7 L 4-cylinder [2TR-FE] engine) SAE 5W-30 (4.0 L V6 [1GR-FE] engine)
Page 563 TABLE OF CONTENTS Index 1-6. Theft deterrent system Before driving Engine immobilizer system ... 78 1-7. Safety information 1-1. Key information Correct driving posture ..80 Keys ........30 SRS airbags ......82 Front passenger occupant 1-2. Opening, closing and locking classification system...
Page 564 2-4. Using other driving systems Interior and exterior Cruise control...... 170 features Rear view monitor system (vehicles with auto 3-1. Using the air conditioning anti-glare inside rear view system and defogger mirror) ....... 173 Air conditioning system ..236 Four-wheel drive system..177 Active traction control 3-2.
Page 565 TABLE OF CONTENTS Index 3-4. Using the interior lights Maintenance and care Interior lights list ....308 • Interior light ....... 309 • Personal lights ....309 4-1. Maintenance and care Cleaning and protecting 3-5. Using the storage features the vehicle exterior ... 354 List of storage features..
Page 566 When trouble arises Vehicle specifications 5-1. Essential information 6-1. Specifications Emergency flashers .... 430 Maintenance data (fuel, oil level, etc.) ... 484 If your vehicle needs to be towed ......431 Fuel information....504 If you think something Tire information ....507 is wrong ......

Toyota Tacoma 2011 Quick Reference Manual

3-2. Using the Audio System Audio System Types

Before Driving 1

Quick Links

QUICK REFERENCE

Chapters

Related Manuals for Toyota Tacoma 2011

Summary of Contents for Toyota Tacoma 2011