Toyota Tacoma 2012 Owner's Manual
Hide thumbs Also See for Tacoma 2012:
Table of Contents

Advertisement

For your information

Main Owners Manual
Please note that this manual applies to all models explains and all equip-
ment, including options. Therefore, you may find some explanations for
equipment not installed on your vehicle.
All specifications provided in this manual are current at the time of printing.
However, because of the Toyota policy of continual product improvement, we
reserve the right to make changes at any time without notice.
Depending on specifications, the vehicle shown in the illustrations may differ
from your vehicle in terms of equipment.
Noise from under vehicle after turning off the engine
Approximately five hours after the engine is turned off, you may hear sound
coming from under the vehicle for several minutes. This is the sound of a fuel
evaporation leakage check and, it does not indicate a malfunction.
Accessories, spare parts and modification of your Toyota
A wide variety of non-genuine spare parts and accessories for Toyota
vehicles are currently available in the market. You should know that Toyota
does not warrant these products and is not responsible for their
performance, repair, or replacement, or for any damage they may cause to,
or adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non-genuine Toyota products.
Modification with non-genuine Toyota products could affect its performance,
safety or durability, and may even violate governmental regulations. In
addition, damage or performance problems resulting from the modification
may not be covered under warranty.
24

Advertisement

Table of Contents
loading

Summary of Contents for Toyota Tacoma 2012

  • Page 1: For Your Information

    Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
  • Page 2 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
  • Page 3 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
  • Page 4 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
  • Page 6: Before Driving

    TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior and Air conditioning and audio systems, as well as other in- exterior features terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
  • Page 7: Table Of Contents

    TABLE OF CONTENTS Index 1-6. Theft deterrent system Before driving Engine immobilizer system ... 78 1-7. Safety information 1-1. Key information Correct driving posture ..80 Keys ........30 SRS airbags ......82 Front passenger occupant 1-2. Opening, closing and locking classification system...
  • Page 8 2-4. Using other driving systems Interior and exterior Cruise control...... 170 features Rear view monitor system (vehicles with auto 3-1. Using the air conditioning anti-glare inside rear view system and defogger mirror) ....... 173 Air conditioning system ..236 Four-wheel drive system..177 Active traction control 3-2.
  • Page 9 TABLE OF CONTENTS Index 3-4. Using the interior lights Maintenance and care Interior lights list ....308 • Interior light ....... 309 • Personal lights ....309 4-1. Maintenance and care Cleaning and protecting 3-5. Using the storage features the vehicle exterior ... 354 List of storage features..
  • Page 10 When trouble arises Vehicle specifications 5-1. Essential information 6-1. Specifications Emergency flashers .... 430 Maintenance data (fuel, oil level, etc.) ... 484 If your vehicle needs to be towed ......431 Fuel information....504 If you think something Tire information ....507 is wrong ......
  • Page 11 Pictorial index Exterior Regular Cab models Windshield wipers P. 167 Outside rear view mirrors P. 68 Hood P. 370 Parking and front side marker lights P. 164 Headlights P. 164 Front turn signal lights and daytime P. 153, 165 running lights...
  • Page 12 Back window P. 73 Rear turn signal lights P. 153 Fuel filler door P. 74 Stop/tail lights P. 164 Side doors P. 35 Tailgate P. 40 License plate lights P. 164 Tires ●Rotation P. 388 ●Replacement P. 450 Rear side marker lights P.
  • Page 13 Pictorial index Exterior Access Cab models Windshield wipers P. 167 Outside rear view mirrors P. 68 Hood P. 370 Parking and front side marker lights P. 164 Headlights P. 164 Fog lights P. 166 Front turn signal lights and daytime running lights P.
  • Page 14 Rear turn signal Back window P. 73 lights P. 153 Fuel filler door P. 74 Stop/tail lights P. 164 Access doors P. 39 Side doors P. 35 Tailgate P. 40 License plate lights P. 164 Tires ●Rotation P. 388 ●Replacement P.
  • Page 15 Pictorial index Exterior Double Cab models Windshield wipers P. 167 Outside rear view mirrors P. 68 Hood P. 370 Parking and front side marker lights P. 164 Headlights P. 164 Fog lights P. 166 Front turn signal lights and daytime running lights P.
  • Page 16 Back window P. 73 Rear turn signal Fuel filler door P. 74 lights P. 153 Side doors P. 35 Stop/tail lights P. 164 Tailgate P. 40 License plate lights P. 164 Rear side marker lights P. 164 Tires ●Rotation P. 388 ●Replacement P.
  • Page 17 Pictorial index Interior Seat belts P. 58 Bottle holders P. 314 Front console box P. 311 Head restraints P. 54 Horn P. 156 SRS driver airbag P. 82 SRS front passenger airbag P. 82 Glove box P. 311 Rear seats P.
  • Page 18 Accessory meter P. 163 Outside temperature display P. 322 Compass P. 347 Garage door opener box P. 343 Personal lights P. 309 Overhead console P. 318 Interior light P. 309 SRS curtain shield airbags P. 82 Sun visors P. 319 Anti-glare inside rear view mirror P.
  • Page 19 Pictorial index Interior Door lock switch P. 36 Inside door lock button P. 36 Power window switches P. 71 Window lock switch P. 71...
  • Page 20 Bench type front seat Shift lever P. 147, 150 Cup holders P. 312 Shift lock override button P. 469 Separated type front seats with an automatic transmission Shift lever P. 147 Cup holders P. 312 Cup holders P. 312 Shift lock override button P.
  • Page 21 Pictorial index Interior Separated type front seats with a manual transmission Shift lever P. 150 Cup holders P. 312...
  • Page 22 Access Cab models Sub woofer P. 270 Back window lock release lever P. 73 Auxiliary boxes P. 316 Rear console box P. 311 : If equipped...
  • Page 23 Pictorial index Interior Double Cab models Grocery bag hooks P. 341 Back window lock Bottle holders P. 314 release lever P. 73 Flashlight holder P. 340 Storage boxes P. 339 Cargo net hooks P. 342 : If equipped : Vehicles with sub woofer...
  • Page 24 Pictorial index Instrument panel Gauges and meters P. 157 Tilt and telescopic steering lock release lever P. 64 Tire pressure warning reset switch P. 388 Hood lock release lever P. 370 Parking brake pedal P. 154 Auxiliary box P. 316 Bottle holders P.
  • Page 25 Pictorial index Instrument panel Passenger airbag Audio system P. 244 off switch P. 95 Air conditioning system P. 236 Front-wheel drive Emergency flasher switch P. 430 control switch P. 177 A-TRAC switch P. 181 AUX port P. 271 Power outlet P.
  • Page 26: Windshield Wipers

    Windshield wipers and Engine (ignition) switch P. 144 washer switch P. 167 Parking brake lever P. 154 Audio remote control switches Telephone switches P. 281 P. 273 Talk switch P. 281 Cruise control switch P. 170 : If equipped : Access Cab models only : 4WD models only : Vehicles with a manual transmission...
  • Page 27 Pictorial index Instrument panel Fog light switch P. 166 RR DIFF LOCK switch P. 185 Instrument panel light control dial P. 158 Power outlet main switch P. 325 Headlight switch P. 164 Turn signal lever P. 153 RSCA OFF switch P.
  • Page 28 Pictorial index Luggage compartment Deck rails P. 202 Tie-down cleats P. 337 Power outlet P. 325 Auxiliary boxes P. 335 Deck hooks P. 336 : If equipped : 4WD models only...
  • Page 29 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Two Wheel Drive Four Wheel Drive Anti-Lock Brake System Accessory Automatic Locking Retractor A-TRAC Active Traction Control AUTO LSD Automatic Limited Slip Differential Child Restraint System Downhill assist control Electronic Control Unit Event Data Recorder Emergency Locking Retractor GAWR Gross Axle Weight Rating...
  • Page 30 ABBREVIATIONS MEANING TPMS Tire Pressure Warning System TRAC Traction Control Treadwear indicators Vehicle Identification Number Vehicle Stability Control...
  • Page 31: Key Information Keys

    Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. ( P. 470)
  • Page 32 1-1. Key information NOTICE ■ To prevent key damage (vehicles with engine immobilizer system) ● Do not subject the keys to strong shocks, expose them to high tempera- tures by placing them in direct sunlight, or get them wet. ● Do not expose the keys to electromagnetic materials or attach any mate- rial that blocks electromagnetic waves to the key surface.
  • Page 33: Opening, Closing And Locking The Doors

    1-2. Opening, closing and locking the doors Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
  • Page 34 ■ Customization that can be configured at Toyota dealer Settings (e.g. wireless remote control system) can be changed. (Customizable features...
  • Page 35 1-2. Opening, closing and locking the doors ■ Certification for wireless remote control MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ4-34R IC (Canada) IDs: Transmitter: 1470A-1T Receiver: 1470A-6R MADE IN U.S.A. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
  • Page 36: Side Doors

    1-2. Opening, closing and locking the doors Side doors The vehicle can be locked/unlocked using the wireless remote con- trol, key or door lock switch. ■ Wireless remote control (if equipped) P. 32 ■ Regular Cab models Locks the door Unlocks the door Access Cab and Double Cab models Locks all doors...
  • Page 37 1-2. Opening, closing and locking the doors ■ Door lock switch (if equipped) Driver’s door lock switch Locks all doors Unlocks all doors Passenger’s door lock switch Locks all doors Unlocks all doors ■ Inside door lock button Locks the door Unlocks the door Pulling the inside handle can open the front door even if the...
  • Page 38 1-2. Opening, closing and locking the doors Locking the front doors from the outside without a key Move the inside door lock button to the lock position. Close the door. Vehicles with power door lock system The door cannot be locked if a front door is open and the key is in the engine switch.
  • Page 39 1-2. Opening, closing and locking the doors CAUTION ■ To prevent an accident Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●...
  • Page 40: Access Doors (Access Cab Models Only)

    1-2. Opening, closing and locking the doors Access doors (Access Cab models only) The access door (rear door) can be opened using the inside handle. Open the front door widely Pull (from the outside) or push (from the inside) the inside handle of the access door.
  • Page 41: Tailgate

    1-2. Opening, closing and locking the doors Tailgate The tailgate can be opened. Pull the handle Open the tailgate slowly The support cables will hold the tailgate horizontal. After closing the tailgate, try pulling it toward you to make sure it is securely locked. Removing the tailgate ■...
  • Page 42 1-2. Opening, closing and locking the doors To disconnect the wire harness connectors ( ), press and hold the lock of the tailgate wire harness connector (White) and pull apart. Tailgate wire harness connec- tor (White) Frame wire harness connector (Gray) Attach connector...
  • Page 43 1-2. Opening, closing and locking the doors Pull out the wire harness from the vehicle bed. Attach connector cover (Gray) to the tailgate wire har- ness connector (White). Tailgate wire harness connec- tor (White) Connector cover (Gray) ■ Removing the tailgate Open the tailgate to the angle where you can release the brackets on the support cables...
  • Page 44 1-2. Opening, closing and locking the doors Slide the tailgate a little to the right to unhook the left side. To attach the tailgate, follow the removal procedure in reverse order. Rear step bumper For rear end protection and eas- ier step-up loading.
  • Page 45 1-2. Opening, closing and locking the doors NOTICE ■ To prevent damage to the tailgate wire harness Do not pull out all of the tailgate wire harness before open the tailgate. ■ To prevent damage to the camera lens (vehicles with rear view monitor system) Store the removed tailgate with the back-up camera lens facing upward.
  • Page 46: Adjustable Components (Seats, Mirrors, Steering Wheel)

    1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Bench type seat Seat position adjustment lever Separated type seats Seat position adjustment lever Driver’s seat lumbar sup- port adjustment knob (if equipped) Seatback angle adjustment lever...
  • Page 47 1-3. Adjustable components (seats, mirrors, steering wheel) Moving passenger’s seat for rear seat entry (if equipped) Lift the seatback angle adjusting lever or press the pedal behind the seatback. The seat will slide forward. Move the seat to the front-most position.
  • Page 48 1-3. Adjustable components (seats, mirrors, steering wheel) Folding passenger’s seat (vehicles with seatback table) Pull the seatback angle adjusting lever and raise the seatback to its upright position. Pull the seatback folding lever and fold the seatback down.
  • Page 49 1-3. Adjustable components (seats, mirrors, steering wheel) Active head restraints (Access Cab and Double Cab models only) When occupant’s back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward to help reduce the risk of whiplash on the seat occupant.
  • Page 50 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
  • Page 51: Rear Seats (Access Cab And Double Cab Models)

    1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats (Access Cab and Double Cab models) Access Cab models The bottom cushion of the rear seats can be raised and lowered. ■ Before raising the bottom cushion Stow the seat belt buckles. This prevents the seat belt buckles from falling out when you fold the seatback.
  • Page 52 1-3. Adjustable components (seats, mirrors, steering wheel) Double Cab models The seatback of the rear seat can be folded. ■ Before folding rear seats Stow the rear seat belt buck- les. This prevents the seat belt buckles from falling out when you fold the seatback.
  • Page 53 1-3. Adjustable components (seats, mirrors, steering wheel) Attach the head restraints to the holders located on the back sides of the bottom cush- ions. Fold down the seatback by pulling the lock release strap. CAUTION ■ When the seatback is folded/the bottom cushion is raised Do not sit on or place anything on the seatback or auxiliary box while driving.
  • Page 54 1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE ■ Before folding the seats The seat belts buckles must be stowed.
  • Page 55: Head Restraints

    1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. ■ Adjusting the head restraints Bench type front seat Pull the head restraints up. Down Push the head restraint down while pushing the lock release button.
  • Page 56 1-3. Adjustable components (seats, mirrors, steering wheel) ■ When using the rear head restraints (Access Cab models only) To use Lift up the head restraint until it locks. To fold Pull the head restraint lock release lever to fold the head restraint.
  • Page 57 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Removing the rear head restraints (Double Cab models only) Pull the head restraint up while pushing the lock release button. ■ Installing the front head restraints Bench type seat Align the head restraint with the installa- tion holes and push it down to the lock position.
  • Page 58 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. ■ Adjusting the front center seat (Bench type seat) and rear center seat head restraints (Double Cab models) Always raise the head restraint one level from the stowed position when...
  • Page 59: Seat Belts

    1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
  • Page 60 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the belt (front seats) Move the height adjuster up as needed until you hear a click. Down Push the lock release button and slide the height adjuster down. ■...
  • Page 61 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
  • Page 62 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
  • Page 63 ● Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been...
  • Page 64 ● Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.
  • Page 65: Steering Wheel

    1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and press the lever down. Adjust to the ideal position by moving the steering wheel horizontally and vertically. After adjustment, pull the lever up to secure the steering wheel.
  • Page 66: Anti-Glare Inside Rear View Mirror

    1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position...
  • Page 67 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode ON/ The indicator comes on when automatic mode is turned on.
  • Page 68 1-3. Adjustable components (seats, mirrors, steering wheel) ■ To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them. CAUTION ■ Caution while driving Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
  • Page 69: Outside Rear View Mirrors

    1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted. Power-adjustable type Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch.
  • Page 70 1-3. Adjustable components (seats, mirrors, steering wheel) Manually adjustable type Adjust the mirror up, down, in or out by pushing the mirror surface. Folding back the mirrors Push backward to fold the mir- rors. ■ Mirror operating conditions (vehicles with power-adjustable type only) The engine switch is in the ACC or ON position.
  • Page 71 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When driving the vehicle Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●...
  • Page 72: Opening And Closing The Windows

    1-4. Opening and closing the windows Power windows The power windows can be opened/closed using the following switches. Driver’s power window switches Closing Opening One-touch opening (driver’s window only) *: Pressing the switch in the opposite direction will stop win- dow travel partway.
  • Page 73 1-4. Opening and closing the windows ■ The power windows can be operated when The engine switch is in the ON position. ■ Operating the power windows after turning the engine switch off The power windows can be operated for approximately 43 seconds even after the engine switch is turned off.
  • Page 74: Back Window (Vehicles With Sliding Type)

    1-4. Opening and closing the windows Back window (vehicles with sliding type) The back window can be opened and closed using the lock release lever. Open/close Push the lock release lever and slide the back window. ■ Closing the back window Make sure that the back window is securely closed after closing it.
  • Page 75: Refueling

    1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Turn the engine switch off and ensure that all the doors and win- dows are closed. ■ Opening the fuel tank cap Open the fuel filler door.
  • Page 76 1-5. Refueling Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. ■ Fuel types Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] or higher) ■...
  • Page 77 ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
  • Page 78 1-5. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface. ■ To prevent damage to the fuel filler door Do not apply excessive force.
  • Page 79: Theft Deterrent System

    1-6. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the key has been removed from the engine switch to indi-...
  • Page 80 1-6. Theft deterrent system ■ Certifications for the engine immobilizer system For vehicles sold in U.S.A. FCC ID: MOZRI-21BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 81: Safety Information

    1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. ( P. 45) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
  • Page 82 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat while driving. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
  • Page 83: Srs Airbags

    1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and right front...
  • Page 84 1-7. Safety information Airbag system components Vehicles with bench type front seat Vehicles with separated type front seat...
  • Page 85 1-7. Safety information Front passenger airbag Driver’s seat position sen- Curtain shield airbags Driver’s seat belt buckle Side airbags switch AIR BAG ON and AIR BAG Front passenger’s seat belt OFF indicator lights buckle switch warning light Occupant detection system RSCA OFF indicator light (ECU and sensors) Driver airbag...
  • Page 86 1-7. Safety information In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. A chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants. ■...
  • Page 87 1-7. Safety information ● It is possible that in some collisions where the forward deceleration of the vehicle is very close to the designed threshold level, the SRS front air- bags and the seat belt pretensioners may not activate together. ●...
  • Page 88 1-7. Safety information The SRS curtain shield airbags may also deploy under the situation shown in the illustration. ● The angle of vehicle tip-up is marginal. ● The vehicle skids and hits a curb stone. ■ Types of collisions that may not deploy the SRS airbag (front airbags) The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision.
  • Page 89 1-7. Safety information ■ Types of collisions that may not deploy the SRS airbag (side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
  • Page 90 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or...
  • Page 91 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
  • Page 92 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
  • Page 93 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
  • Page 94 Wash off any residue as soon as possible to prevent skin irritation. ● If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.
  • Page 95: Replacement

    Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
  • Page 96: Information

    1-7. Safety information Passenger airbag off switch (Access Cab models) The passenger airbag off switch is designed to disable the front pas- senger airbag in order to allow usage, if necessary, of the front pas- senger seat by a member of a passenger risk group identified in TABLE 1 is occupying the front passenger seating position ( P.
  • Page 97 1-7. Safety information ■ Passenger risk group TABLE 1: A PASSENGER RISK GROUP Infant. An infant (less than 1 year old) who must ride in the front seat because: • Vehicle has no rear seat; • Vehicle has a rear seat too small to accommodate a rear-facing infant seat;...
  • Page 98 1-7. Safety information CAUTION ■ When the passenger airbag off switch is turned off ● Do not turn the passenger airbag off switch to the OFF position except when a member of a passenger risk group identified in TABLE 1 is occupy- ing the front passenger seating position.
  • Page 99 1-7. Safety information CAUTION ■ For normal driving Make sure the RSCA OFF indicator is not turned on. If it is left on, the curtain shield airbag will not activate in the event of an accident, which may result in death or serious injury.
  • Page 100: Front Passenger Occupant Classification System

    1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the right front passenger seat and activates or deactivates the devices for the front passenger.
  • Page 101 1-7. Safety information Conditions and operation of the front passenger occupant classification system Regular Cab and Double Cab models ● Indicator/warning light Condition detected AIR BAG ON Front passen- by the front passen- and AIR BAG SRS warning ger’s seat belt ger occupant clas- OFF indicator light...
  • Page 102 1-7. Safety information : The right front passenger on the bench seat. : The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture.
  • Page 103 1-7. Safety information Access Cab models ● Indicator/warning light AIR BAG Front pas- Condition detected Passen- ON and senger’s by the front passen- ger airbag AIR BAG warning seat belt ger occupant clas- off switch reminder OFF indi- light sification system position light cator lights...
  • Page 104 1-7. Safety information ● Devices Condition Curtain detected by Passen- Side air- Front shield air- Front pas- the front pas- ger air- bag on passen- bag in the senger’s senger occu- bag off the front front pas- ger air- seat belt pant switch passen-...
  • Page 105 1-7. Safety information : In case the indicator is not illuminated, consult this manual for installing the child restraint system properly. ( P. 111) CAUTION ■ Front passenger occupant classification system precautions Observe the following precautions regarding front passenger occupant clas- sification system.
  • Page 106 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
  • Page 107: Child Restraint Systems

    1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
  • Page 108 1-7. Safety information Forward facing — Convertible seat Booster seat ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt. ●...
  • Page 109 ● Access Cab and Double Cab models: Toyota strongly urges the use of a proper child restraint system that conforms to the size of the child, installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.
  • Page 110 1-7. Safety information CAUTION ■ Child restraint precautions ● Access Cab models: Never install a rear-facing child restraint system on the front passenger seat with the passen- ger airbag off switch in the AUTO posi- tion. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-fac-...
  • Page 111 1-7. Safety information CAUTION ■ Child restraint precautions ● Bench type front seat: The driver and passengers sit on a bench seat in this vehicle. Therefore, when installing a child restraint system, the seat must be moved back from the SRS airbag as far as possible while also maintaining the driver’s seating position.
  • Page 112: Installing Child Restraints

    1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
  • Page 113 1-7. Safety information ■ Using the seat belts Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) ( P. 58) ■ Using the top tether strap Regular Cab models with bench type seat Anchor bracket (for top tether strap) Anchor brackets are pro-...
  • Page 114 1-7. Safety information Regular Cab models with separated type seat Anchor bracket (for top tether strap) Anchor bracket is provided for passenger seat. Access Cab models Anchor bracket (for top tether strap) Anchor brackets are pro- vided for the front passen- seat left rear...
  • Page 115 1-7. Safety information Double Cab models Anchor bracket (for top tether strap) Anchor brackets are pro- vided for all rear passenger seats. Installing the child restraint system on the front passenger seat (Access Cab models) When you install a child restraint system which belongs to a passen- ger risk group on the front passenger seat, do the following proce- dure.
  • Page 116 1-7. Safety information CAUTION ■ Rear-facing child restraint system If you must install a rear-facing child restraint system on the front passenger seat, make sure that the passenger airbag off switch is in the OFF position with the key removed and that the indicator light is on. ■...
  • Page 117 1-7. Safety information Vehicles without seatback table (Type A) Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
  • Page 118 1-7. Safety information Vehicles with seatback table (Type A) Widen the slits of the seat cushion slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched onto...
  • Page 119 1-7. Safety information ■ Installing on the rear seat Type A Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor.
  • Page 120 1-7. Safety information Installation with LATCH system (Double Cab models) Type A Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
  • Page 121 1-7. Safety information Type B Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a...
  • Page 122 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
  • Page 123 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
  • Page 124 1-7. Safety information ■ Booster seat Place the booster seat on the seat facing the front of the vehi- cle. Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle.
  • Page 125 1-7. Safety information Child restraint systems with a top tether strap (Regular Cab models) ■ Bench type seat Remove the head restraint. Installing position: Right side passenger seat Center passenger seat Swing the seatback forward slightly ( P. 46) and remove the anchor bracket covers.
  • Page 126 1-7. Safety information Center passenger seat Route the top tether strap through the routing device as shown in the illustration. Make sure the top tether strap is not twisted. Latch the hook onto the anchor bracket. Return the seatback to its orig- inal position.
  • Page 127 1-7. Safety information ■ Separated type seat Remove the head restraint. Swing the seatback forward slightly ( P. 46) and remove the anchor bracket cover. Store the removed cover in a safe place such as the glove box. Route the top tether strap through the routing device as shown in the illustration.
  • Page 128 1-7. Safety information Replace the head restraint. Child restraint systems with a top tether strap (Access Cab models) ■ Installing on the front seat Remove the head restraint. Remove the anchor bracket cover. Store the removed cover in a safe place such as the glove box.
  • Page 129 1-7. Safety information Replace the head restraint. ■ Installing on the rear seat Remove the anchor bracket cov- ers. Store the removed covers in a safe place such as the glove box. Secure the child restraint using a seat belt or lower anchors. Route the top tether strap through the routing device as shown in the illustration.
  • Page 130 1-7. Safety information Child restraint systems with a top tether strap (Double Cab models) Remove the head restraint. Installing position: Outside passenger seat Center passenger seat Outside passenger seat Swing the seatback forward slightly. ( P. 51) Latch the hook onto the anchor bracket.
  • Page 131 1-7. Safety information Secure the child restraint using a seat belt or lower anchors, and tighten the top tether strap. Make sure the top tether strap is securely latched. Replace the head restraint. Installing position: Outside passenger seat Center passenger seat ■...
  • Page 132 1-7. Safety information CAUTION ■ When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. ( P. 60) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
  • Page 133 1-7. Safety information CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
  • Page 134: Driving Procedures

    2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine P. 144 ■ Driving Automatic transmission With the brake pedal depressed, shift the shift lever to D. ( P. 147) Release the parking brake.
  • Page 135 2-1. Driving procedures ■ Parking the vehicle Automatic transmission With the shift lever in D, depress the brake pedal. Set the parking brake. ( P. 154) Shift the shift lever to P. ( P. 147) When parking on a hill, if necessary, block the wheels. Turn the engine switch off to stop the engine.
  • Page 136: Tires

    ■ Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended to observe: ●...
  • Page 137 If the smell of exhaust is noticed inside the vehicle, open the windows and check that the back window is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. ●...
  • Page 138: Tires

    2-1. Driving procedures CAUTION ■ When driving the vehicle ● Do not shift the shift lever to N while the vehicle is moving. Doing so may cause the engine brake to not operate properly and lead to an accident. ● Do not turn the engine off while driving.
  • Page 139 2-1. Driving procedures CAUTION ■ When driving on slippery road surfaces ● After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.
  • Page 140 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in...
  • Page 141 Exhaust gases ● Toyota does not recommend occupying the rear cargo area when it is fitted with a slide-in camper, camper shell or other type cover while the engine is running. This caution applies to both driving and stopped or parked situa- tions with the engine running.
  • Page 142 If you hear a squealing or scraping noise while driving (brake pad wear limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed.
  • Page 143 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ● Brake function ●...
  • Page 144: Engine (Ignition) Switch

    2-1. Driving procedures Engine (ignition) switch ■ Engine switch LOCK The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in P.) Some electrical components such as the audio system can be used.
  • Page 145 2-1. Driving procedures ■ Turning the key from ACC to LOCK Shift the shift lever to P (auto- matic transmission) or N (man- ual transmission). ( P. 147 150) Push in the key and turn to the LOCK position. ■ Steering lock release When starting the engine, the engine switch may seem stuck in the LOCK posi-...
  • Page 146 2-1. Driving procedures CAUTION ■ Caution while driving Do not turn the engine switch to the LOCK position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the ACC position. NOTICE ■...
  • Page 147: Automatic Transmission

    2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever 5-speed models While the engine switch is on, depress the brake pedal and move the shift lever. : If equipped...
  • Page 148 2-1. Driving procedures 4-speed models While the engine switch is on, depress the brake pedal and move the shift lever. ■ Shift position uses Function Shift position 5-speed models 4-speed models Parking the vehicle or starting the engine Reversing Neutral Normal driving Position for engine brak- —...
  • Page 149 2-1. Driving procedures ■ Downshifting restrictions The shift lever cannot be downshifted if the following speeds are exceeded. 2WD models mph (km/h) Maximum speed Downshifting 5-speed models 4-speed models 82 (133) — 54 (88) 74 (119) 24 (39) 35 (57) 4WD models mph (km/h) Maximum speed...
  • Page 150: Manual Transmission

    2-1. Driving procedures Manual transmission ■ Shifting the shift lever 6-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly. 5-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly.
  • Page 151 2-1. Driving procedures ■ Maximum allowable speed Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. 2WD models except PreRunner mph (km/h) Maximum speed Shift position 6-speed models 5-speed models 32 (52) 33 (53) 61 (99) 63 (101) 91 (146)
  • Page 152 2-1. Driving procedures 4WD models mph (km/h) Maximum speed Shift position Transfer position 6-speed models 5-speed models H2 and H4 30 (49) 30 (48) 11 (19) 11 (18) H2 and H4 58 (93) 57 (92) 22 (36) 22 (36) H2 and H4 85 (137) 82 (133) 33 (53)
  • Page 153: Turn Signal Lever

    2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
  • Page 154: Parking Brake

    2-1. Driving procedures Parking brake Lever type ● Sets the parking brake Fully set the parking brake while depressing the brake pedal. At this time, the indicator will come on. ● Release the parking brake Press the button Turn the lever clockwise Press it in completely Pedal type Sets...
  • Page 155 2-1. Driving procedures ■ Parking brake engaged warning buzzer The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reach a speed of 3 mph [5 km/h]). ■ Usage in winter time See “Winter driving tips” for parking brake usage in winter time. ( P. 209) NOTICE ■...
  • Page 156: Horn

    2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. ( P.
  • Page 157: Gauges And Meters

    2-2. Gauges and meters Gauges and meters The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Engine coolant temperature gauge Displays the engine coolant temperature.
  • Page 158 2-2. Gauges and meters Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.
  • Page 159 2-2. Gauges and meters NOTICE ■ To prevent damage to the engine and its components ● Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. ● The engine may be overheating if the engine coolant temperature gauge is in the red zone (H).
  • Page 160: Indicators And Warning Lights

    2-2. Gauges and meters Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster Center panel...
  • Page 161 2-2. Gauges and meters ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Slip indicator ( P. 153) ( P. 181, 183, 192) Headlight high beam VSC OFF indicator indicator ( P. 164) ( P.
  • Page 162 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
  • Page 163: Accessory Meter

    2-2. Gauges and meters Accessory meter Outside temperature Displays the outside air temperature. ( P. 322) Compass Displays the direction that the vehicle is heading. ( P. 347) Display button Every time you press this button, the display toggles through the following infor- mation.
  • Page 164: Operating The Lights And Wipers

    2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually. Turning the end of the lever turns on the lights as follows: Vehicles with daytime running light system: The daytime running lights turn on. The side marker, park- ing, tail, license plate, daytime running lights equipped)
  • Page 165 2-3. Operating the lights and wipers ■ Daytime running light system (if equipped) ● To make your vehicle more visible to other drivers, the front turn signal lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night.
  • Page 166: Fog Light Switch

    2-3. Operating the lights and wipers Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. On/off ■ The fog lights can be turned on only when The headlights are on low beam. : If equipped...
  • Page 167: Windshield Wipers And Washer

    2-3. Operating the lights and wipers Windshield wipers and washer ■ Without intermittent type Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Washer operation...
  • Page 168 2-3. Operating the lights and wipers ■ Intermittent wiper with interval adjuster Wiper intervals can be adjusted for intermittent operation (when is selected). Intermittent windshield wiper operation Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency...
  • Page 169 2-3. Operating the lights and wipers Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. ■ The windshield wiper and washer can be operated when The engine switch must be in the ON position. ■...
  • Page 170: Using Other Driving Systems

    2-4. Using other driving systems Cruise control Use cruise control to maintain a set speed without using the acceler- ator. Indicator Cruise control switch ■ Set the vehicle speed Press the ON-OFF button to turn the cruise control on. At this time, the cruise control indicator will come on.
  • Page 171 2-4. Using other driving systems ■ Adjusting the speed setting Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.
  • Page 172 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. CAUTION ■...
  • Page 173: Rear View Monitor System (Vehicles With Auto Anti-Glare Inside Rear View Mirror)

    2-4. Using other driving systems Rear view monitor system (vehicles with auto anti-glare inside rear view mirror) The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen.
  • Page 174 2-4. Using other driving systems ■ Switching the screen ON/OFF mode While displaying the screen, press the AUTO button on the inside rear view mir- ror to switch the screen ON/OFF mode. Screen ON mode: Green indicator comes Screen OFF mode: Orange indicator comes on.
  • Page 175: Headlights

    2-4. Using other driving systems ■ Rear view monitor system camera In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly. ● The vehicle is in a dark area, such as at night.
  • Page 176: Tires

    Conditions which may affect the rear view monitor system ● If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer. ● As the camera has a water proof construction, do not detach, disassemble or modify it.
  • Page 177: Four-Wheel Drive System

    2-4. Using other driving systems Four-wheel drive system Use the front-wheel drive control switch to select the following transfer modes. H2 (high speed position, two-wheel drive) Normal driving H4 (high speed position, four-wheel drive) Greater traction than two wheel drive. When you experience a loss of power, such as wheel slipping.
  • Page 178 2-4. Using other driving systems Shifting between H4 and L4 ■ Shifting from H4 to L4 Automatic transmission Stop the vehicle completely. Shift the shift lever to N. Push and turn the front-wheel drive control switch fully clock- wise. If the four-wheel drive indicator flashes and the buzzer sounds, try the above steps again.
  • Page 179 If the indicator light continues to blink even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the four-wheel drive...
  • Page 180 2-4. Using other driving systems ■ Shifting to L4 VSC is automatically turned off. ■ Four-wheel drive usage frequency You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front-drive components are lubricated. CAUTION ■...
  • Page 181: Active Traction Control System

    2-4. Using other driving systems Active traction control system The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces. ■ System operation Vehicles with an automatic transmission: Stop the vehicle, shift the shift lever to N and put the front- wheel drive control switch in the L4 position.
  • Page 182 2-4. Using other driving systems ■ When the rear differential is locked (vehicles with the rear differential lock system) The active traction control system is activated only when the vehicle speed is less than 3 mph (6 km/h). ■ Sounds and vibrations caused by the active traction control system ●...
  • Page 183: Auto Lsd System

    2-4. Using other driving systems AUTO LSD system The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when one of the rear wheels spin- ning occurs in a ditch or rough surface.
  • Page 184 2-4. Using other driving systems ■ Automatic VSC reactivation If the AUTO LSD system is turned on and the vehicle speed decreases, the VSC system will turn off and the VSC OFF indicator will turn on. If the vehi- cle speed increases the VSC system will turn on and the VSC OFF indicator will turn off.
  • Page 185: Rear Differential Lock System

    2-4. Using other driving systems Rear differential lock system The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning.
  • Page 186 2-4. Using other driving systems Manual transmission 4WD models: Before using the rear differential lock system. Stop the vehicle or reduce your speed to less than 2 mph (3 km/h). Depress the clutch pedal and put the front-wheel drive control switch in the L4 position to see if this is sufficient. If this has no effect, additionally use the rear differential lock system.
  • Page 187 2-4. Using other driving systems ■ After unlocking the rear differential To check that the indicator goes off, turn the engine switch to the ON posi- tion, but do not start the engine. CAUTION ■ To avoid an accident ● Do not use the rear differential lock system except when wheel spinning occurs in a ditch or on a slippery or ragged surface.
  • Page 188: Downhill Assist Control System

    2-4. Using other driving systems Downhill Assist Control system The downhill assist control system helps to prevent excessive speed on steep downhill descents. ■ System operation The system will operate when the vehicle is traveling under 15 mph (25 km/h) and the front-wheel drive control switch is in the L4 position.
  • Page 189 ● The downhill assist control system indicator does not come on when the DAC switch is pressed. In the above cases have your vehicle checked by your Toyota dealer. CAUTION ■ Do not rely excessively on the downhill assist control system It may not be able to maintain a low speed over road surfaces on which slid- ing can easily occur, such as extremely steep slopes or icy or muddy roads.
  • Page 190: Clutch Start Cancel Switch

    2-4. Using other driving systems Clutch start cancel switch The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged. Never use the switch for normal engine starting. Be sure to follow the starting procedure.
  • Page 191: Driving Assist Systems

    2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
  • Page 192 2-4. Using other driving systems When the VSC/TRAC/hill-start assist control systems are operating If the vehicle is in danger of slip- ping, the rear wheels (2WD mod- els) four wheels (4WD models) spin, the vehicle starts to roll backwards when starting on an incline, this indicator flashes to indicate that the VSC/ TRAC/hill-start...
  • Page 193 2-4. Using other driving systems ■ Turning off TRAC and VSC Press and hold the VSC OFF switch for more than 3 seconds while the vehicle is stopped to turn off both TRAC and VSC. The VSC OFF indicator light should come on.
  • Page 194 2-4. Using other driving systems ■ Hill-start assist control is operational when (if equipped) ● The shift lever is in the D, 4, 3, 2 (5-speed automatic transmission), D, 3, 2 (4-speed automatic transmission) or L positions. ● The brake pedal is not depressed. ■...
  • Page 195: Tires

    In addition, make sure that the tires are inflated to the appro- priate tire pressure level. The ABS and VSC will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.
  • Page 196: Tires

    2-4. Using other driving systems CAUTION ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.
  • Page 197: Driving Information Off-Road Precautions (4Wd Models And Prerunner)

    2-5. Driving information Off-road precautions (4WD models and PreRunner) This vehicle has higher ground clearance and narrower tread in rela- tion to the height of its center of gravity to make it capable of per- forming in a wide variety of off-road applications. Off-road vehicle feature ●...
  • Page 198 2-5. Driving information CAUTION ■ Off-road vehicle precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
  • Page 199 2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
  • Page 200 2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to minimize the risk of serious injury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places. ●...
  • Page 201 2-5. Driving information NOTICE ■ To prevent the water damage ● Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ●...
  • Page 202: Cargo And Luggage

    ● For better fuel economy, do not carry unnecessary weight. ■ Deck rails Headboard rail Side rails To use the deck rails, you must install genuine Toyota accessories or their equiva- lent for the deck rails. Follow manufacturer’s instructions and precautions...
  • Page 203 2-5. Driving information CAUTION ■ When you secure cargo with the deck rails ● Spread out tie-down/support locations evenly along the length of the rails. ● Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail. ●...
  • Page 204 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Example on your vehicle Cargo capacity Total load capacity...
  • Page 205 2-5. Driving information CAUTION ■ Things that must not be carried in the luggage compartment The following things may cause a fire if loaded in the luggage compart- ment. ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions. Failing to do so may result in death or serious injury.
  • Page 206 2-5. Driving information CAUTION ■ Capacity and distribution ● Do not exceed the maximum axle weight rating or the total vehicle weight rating. ● Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.
  • Page 207: Vehicle Load Limits

    2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. ■ Total load capacity: ( P. 485) Total load capacity means the combined weight of occupants, cargo and luggage. ■...
  • Page 208: Tires

    2-5. Driving information CAUTION ■ Overloading the vehicle Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
  • Page 209: Winter Driving Tips

    2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
  • Page 210: Tires

    2-5. Driving information ■ When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. ■ When parking the vehicle Park the vehicle and move the shift lever to P (automatic trans- mission) or 1 or R (manual transmission) without setting the parking brake.
  • Page 211: Tires

    2-5. Driving information ■ Snow chain installation Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the rear tires only. Do not install tire chains on the front tires.
  • Page 212: Replacement

    NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
  • Page 213: Trailer Towing

    To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional...
  • Page 214 2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
  • Page 215 2-5. Driving information ■ TWR (Trailer Weight Rating) The maximum allowable gross (With brakes) trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer. TWR is calculated assuming base vehicle with one driver, one front passenger, towing package (if available), hitch and hitch sys-...
  • Page 216 2-5. Driving information Weight limits ● The gross trailer weight must never exceed the TWR described in the table. ( P. 217, 487) ● The gross combination weight must never exceed the GCWR described in the table. ( P. 217) Regular Cab models and Double Cab models ●...
  • Page 217 2-5. Driving information Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR and TWR Regular Cab models Driving Model code Engine GCWR system TRN220L- 7140 lb.
  • Page 218 2-5. Driving information Access Cab models Driving Model code Engine GCWR system TRN225L- 7430 lb. CRMDKA (3370 kg) TRN225L- 7450 lb. (3379 kg) CRPDKA 2.7 L TRN245L- 4-cylinder 7790 lb. 3500 lb. CRMDKA (2TR-FE) (3533 kg) (1587 kg) engine TRN245L- 7810 lb.
  • Page 219 2-5. Driving information Double Cab models Driving Model code Engine GCWR system TRN225L- 7530 lb. 3400 lb. 2.7 L PRPDKA (3415 kg) (1542 kg) 4-cylinder (2TR-FE) TRN265L- 7660 lb. 3500 lb. engine PRPDKA (3474 kg) (1587 kg) 8040 lb. 3500 lb. (3646 kg) (1587 kg) GRN245L-...
  • Page 220 : With towing package ■ Unbraked TWR 1000 lb. (453 kg) ■ Fifth wheel and gooseneck towing TWR Toyota does not recommend fifth wheel and gooseneck towing. : These models meet the tow-vehicle trailering requirement of SAE International per SAE J2807.
  • Page 221 2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. •...
  • Page 222 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
  • Page 223: Information

    2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
  • Page 224 2-5. Driving information Positions for towing hitch receiver and hitch ball Weight carrying ball position: 56.1 in. (1425 mm) Hitch receiver pin hole posi- tion: 44.2 in. (1123 mm) Connecting trailer lights Use the wire harness stored in the rear end under the vehicle body.
  • Page 225: Tires

    ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
  • Page 226 2-5. Driving information ● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak- ing a turn. ● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.
  • Page 227 2-5. Driving information ● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in 1 or R (manual transmission). Avoid parking on a slope, but if unavoid- able, do so only after performing the following: Apply the brakes and keep them applied.
  • Page 228: Tires

    2-5. Driving information ■ Matching trailer ball height to trailer coupler height No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer. Coupler Trailer ball ■...
  • Page 229: Tires

    Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
  • Page 230 2-5. Driving information If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases. CAUTION ■...
  • Page 231 ■ When towing a trailer Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. ● If the gross trailer weight exceeds unbraked TWR, trailer brakes are required.
  • Page 232 2-5. Driving information NOTICE ■ When installing a trailer hitch Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ■ Do not directly splice trailer lights Do not directly splice trailer lights.
  • Page 233: Dinghy Towing

    2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
  • Page 234 2-5. Driving information...
  • Page 235: Using The Air Conditioning System And Defogger

    3-1. Using the air conditioning system and defogger Air conditioning system Type A Temperature control dial Fan speed control dial Air outlet selection dial Outside air or recirculated air mode switch Type B Temperature control dial Fan speed control dial Air outlet selection dial Outside air or recirculated Air conditioning...
  • Page 236 3-1. Using the air conditioning system and defogger Adjusting the settings ■ Adjusting the temperature setting (Type A) Turn the temperature control dial clockwise to increase the temper- ature. ■ Adjusting the temperature setting (Type B) Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).
  • Page 237 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the upper body and feet. Double Cab models only When the dial is set to , air flows to the feet. Double Cab models only When the dial is set to , air flows to the feet and the wind-...
  • Page 238 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the windshield and side windows. The air intake selector is automat- ically set to outside air mode. In this position, the air intake selector cannot be changed to the recirculated air mode.
  • Page 239 3-1. Using the air conditioning system and defogger Adjusting the position of the air outlets Center outlets Direct air flow to the left or right, up or down.
  • Page 240 3-1. Using the air conditioning system and defogger Right and left side outlets Direct air flow to the left or right, up or down. Opening and closing the air outlets Center outlets Open the vent. Close the vent.
  • Page 241 3-1. Using the air conditioning system and defogger Right and left side outlets Open the vent. Close the vent. ■ For quick clearing of the windshield and side windows (type B only) Press to turn the air conditioning on. ■ Using the system in recirculated air mode The windows will fog up more easily if the recirculated air mode is used for an extended period.
  • Page 242 3-1. Using the air conditioning system and defogger ■ Air conditioning odors ● During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents. ●...
  • Page 243: Using The Audio System

    3-2. Using the audio system Audio system types Type A: CD player with CD changer controller and AM/FM radio Type B: CD player with changer and AM/FM radio Type A Type B...
  • Page 244 3-2. Using the audio system Title Page Using the radio P. 247 Using the CD player P. 253 Playing back MP3 and WMA discs P. 259 Optimal use of the audio system P. 267 Operating the sub woofer P. 270 Using the AUX port P.
  • Page 245 3-2. Using the audio system CAUTION ■ For vehicles sold in U.S.A. and Canada ● Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device. ●...
  • Page 246: Using The Radio

    3-2. Using the audio system Using the radio Power Volume Adjusting the Station selector frequency Scanning for receivable stations AM/FM mode buttons Seeking the frequency ® Setting station presets (excluding XM Satellite Radio) Search for desired stations by turning or pressing “ ” or “...
  • Page 247 3-2. Using the audio system ■ Scanning all radio stations within range Press All stations with reception will be played for 5 seconds each. When the desired station is reached, press the button once again to stop scanning. ® Satellite Radio (if equipped) ■...
  • Page 248 3-2. Using the audio system ■ Displaying text information Press The display will show up to 10 characters. The display changes as follows each time the button is pressed. ● CH NAME ● TITLE (SONG/PROGRAM TITLE) ● NAME (ARTIST NAME/FEATURE) ●...
  • Page 249 XM antenna cable is attached securely. ANTENNA There is a short-circuit in the antenna or the sur- rounding antenna cable. See a Toyota certified dealer. ® You have not subscribed to the XM Satellite Radio. The radio is being updated with the latest ®...
  • Page 250 3-2. Using the audio system The unit is acquiring audio or program information. LOADING Wait until the unit has received the information. The channel you selected is not broadcasting any OFF AIR programming. Select another channel. There is no song/program title or artist name/fea- ----- ture associated with the channel at that time.
  • Page 251 3-2. Using the audio system NOTICE ■ To prevent damage, remove the antenna in the following cases. ● The antenna will touch the ceiling of a garage. ● A cover will be put on the vehicle.
  • Page 252: Using The Cd Player

    3-2. Using the audio system Using the CD player CD selection Power Volume (type A with Fast-forward changer and type B) CD load CD eject Reverse (type B only) Random Display text playback message Repeat play Search playback Track selection Playback Loading CDs ■...
  • Page 253 3-2. Using the audio system Insert a CD when the indicator on the slot turns from amber to green. The display changes from “WAIT” to “LOAD”. The indicator on the slot turns to amber when the CD is inserted. Insert the next CD when the indicator on the slot turns from amber to green again.
  • Page 254 3-2. Using the audio system Fast-forwarding and reversing tracks To fast-forward or reverse. Press and hold Selecting a CD (type A with a CD changer and type B) ■ Selecting the desired CD Press ■ Selecting loaded CDs Press and hold until you hear a beep.
  • Page 255 3-2. Using the audio system Switching the display Press Each time the switch is pressed, the display changes in the order of Track no./Elapsed time CD title Track name. ■ Display Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding for 1 second or more will display the remaining characters.
  • Page 256 3-2. Using the audio system ■ If CDs are left inside the CD player or in the ejected position for extended periods CDs may be damaged and may not play properly. ■ Lens cleaners Do not use lens cleaners. Doing so may damage the CD player. NOTICE ■...
  • Page 257 3-2. Using the audio system NOTICE ● CDs that have had tape, stickers or CD- R labels attached to them, or that have had the label peeled off ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself.
  • Page 258: Playing Back Mp3 And Wma Discs

    3-2. Using the audio system Playing back MP3 and WMA discs Power Volume Disc selection Fast-forward (type B only) Disc load (type B only) Disc eject Reverse Random File selection playback Search playback Repeat play Playback File selection Display text message Folder selection Loading MP3 and WMA discs ■...
  • Page 259 3-2. Using the audio system ■ Loading multiple discs (type B only) Press and hold until you hear a beep. “WAIT” is shown on the display. Insert a disc when the indicator on the slot turns from amber to green. The display changes from “WAIT”...
  • Page 260 3-2. Using the audio system Selecting a folder ■ Selecting folders one at a time To select the desired folder, press “ ” or “ ” on ■ Selecting the desired folder by cueing the first file of each folder Press and hold until you hear a beep.
  • Page 261 3-2. Using the audio system Repeat play ■ Repeating a file Press ■ Repeating all of the files in the folder Press and hold until you hear a beep. Random playback ■ Playing files from a particular folder in random order Press ■...
  • Page 262 3-2. Using the audio system ■ Display Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding for 1 second or more will display the remaining characters. A maximum of 24 characters can be displayed. is pressed for 1 second or more again or has not been pressed for 6 seconds or more, the display will return to the first 12 characters.
  • Page 263 3-2. Using the audio system ■ Lens cleaners Do not use lens cleaners. Doing so may damage the MP3 and WMA player. ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression.
  • Page 264 3-2. Using the audio system ● Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.
  • Page 265 3-2. Using the audio system ● MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played.
  • Page 266: Optimal Use Of The Audio System

    3-2. Using the audio system Optimal use of the audio system Displays the current mode Changes the following set- ting • Sound quality and volume balance ( P. 268) The sound quality and bal- ance setting can be changed to produce the best sound. •...
  • Page 267 3-2. Using the audio system ■ Adjusting sound quality Turning adjusts the level. Sound qual- Mode Turn to the Turn to the Level ity mode displayed left right Bass -5 to 5 Midrange -5 to 5 High Treble -5 to 5 Shifts to roof /roof...
  • Page 268 3-2. Using the audio system JBL brand audio system When “ASL” is selected, turning to the right turns “ASL” on, and turning to the left turns “ASL” off. ASL automatically adjusts the volume and tone quality according to vehi- cle speed.
  • Page 269: Operating The Sub Woofer (On Some Access Cab Models)

    3-2. Using the audio system Operating the sub woofer (on some Access Cab models) LIGHT ON The sub woofer illumination turns on. In this position, the sub woofer operates.
  • Page 270: Using The Aux Port

    3-2. Using the audio system Using the AUX port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Connect the portable audio device. Press...

This manual is also suitable for:

TacomaTacoma 2011

Table of Contents