You can refer to the latest operation manual and relative documents by visiting www.joint-tracking.com. Please read those simple guidelines before use, Jointech assured that the products will work properly under normal conditions, the warranty period would be 12 months from the delivery date, the warranty shall not apply to any defect, failure or damage which caused by improper maintenance, repair, alteration.
Ⅲ Product Function Product Function Data transmission mode(SMS/TCP) Track and Control by SMS/GPRS Track by time interval Track by Calling(reply a location short message to mobile phone) Base station Location (CELL ID and LAC) Two-way voice function Automatic answer the call Listen-in function(Voice monitoring) History data (43200 pcs Saving in Flash) History data upload to center automatically...
When an incoming call CALL Ⅱ once Self Geo-fence ON No incoming call. and self Press this button Geo-fence off Note: JT600 will be vibrating if you set this twice within 3sec successfully. and there is a message which - 7 -...
Page 8
And inserted SIM card Send SOS alert to VIP numbers Normal. Power on Press this button Note: JT600 will be vibrating if SOS alert for 3 sec was sent successfully. press the SOS button once, the LED Normal. Power on...
4.3 Working mode GPS Module Wakeup GSM Module Working mode while Note condition while sleeping sleeping both GSM and GPS module work Press any properly, the device can be used Standard button/coming Sleep Power on to call and receive incoming call, call/SMS send and receive text messages at any time.
(Table 2) 4.4 Voice communication JT600 has the two-way voice function, It can dial preset phone numbers and receive phone call as well. When a call coming, the unit will ring, press CALL Ⅰbutton once to receive the call. Press CALL Ⅰ or CALL Ⅱ button for 3 seconds to call the preset VIP number.
5.4 Configure by PC setup software Refer to the manual 《 JT600 Mini-USB Cable Driver InstallationV1.2.pdf》 ,Install the Mini-USB cable driver, and plug it to PC. Copy “JT600 Assistant V3.1” software to your PC and Open it. - 11 -...
Note: If you open this software in Win 7 system, Please right click its ICON, and Click “Run as administrator”, Or This software won’t show the COM port number. 5.4.1 PC setup Software Introductions 5.4.1.1 Main Settings - 12 -...
Page 13
Name Parameter Explain Note Get The COM port number after Refer to the manual《JT600 Com Port plugged the Configuration cable Mini-USB Cable Driver InstallationV1.2.pdf》 Baud Rate 9600 Fixed value Open/Close Open/Close Click it, and Connect to PC Click it ,Pop-up a window shows all...
Page 14
Maximum value 90, minimum value 10. than 20%, there is a low battery Battery alert. China GMT+8. 480minutes JT600 outputs Greenwich time. It has to be Time adjusted to local time. To set time zone behind difference GMT use –(Minus sign) Enable this function, and you Default, This function is disabled.
Page 15
JT600 will answer the coming 1)The SIM card in tracker must be activated call call call automatically after ring 3 screening function. times. Read current tracker’s settings Read for above items. Write above settings to the White tracker.
Page 16
Parameter(e.g.) Explain Note Click it ,enable “Normal If you choose this Uploading Normal Uploading” mode,JT600 will upload data as Radio button Uploading preset time interval and data transmission mode all the time. enable this function,JT600 Default, This function is disabled.
Page 17
10 minutes time points. before getting into the sleep mode. The device supports 48 time points JT600 will wake up when in maximum, but the interval the time at 8:00,9:00,12:00, Radio button between each two points should be Fixed time above 30 minutes.
Page 18
Exclude Geo-fence Restore factory default Restore factory settings. It will clear parameters(such as Geo-fence/Uploading mode) Factory except IP address,Port,SMS Default Primary number, VIP numbers, APN,APN account,Another name and time difference.and JT600 will be reset to Normal Uploading and - 18 -...
SMS mode. show the “operation success” pop-up Show tip checkbox window when read or write the setting message successfully. Language Supports multi-language Save all parameters to PC Save Load all parameters from PC Load 5.4.1.2 Authorization Number - 19 -...
Page 20
Ⅰ Supports country code. And It Call 1 +8615017924411 receives SMS reply message, alert Button for 3 sec,JT600 will call this number. message. Set the second VIP number. Press the CALL Ⅱ Supports country code. And It Button for 3 sec,JT600 will call this number.
Geo-fence. Choose it, So the corresponding VIP number SOS alarm checkbox can receive this alert message Choose it, So the corresponding VIP number Low Battery alarm. Battery alarm checkbox can receive this alert message Read current tracker’s settings for above Read items.
Page 23
Item Parameter(e.g.) Explain Note Click this record and Get the Please Load the Google Geo-Fence on Google map. Map at right side. 1 to 64 Double Click this record and begin to edit this fence. Read all Geo-fence settings Read All Please Load the Google Geo-fence Map at right side.
Page 24
Item Parameter(e.g.) Explain Note Define the default map view when Default Map View you load Google Map Load Google Map Load Google map PC has internet access. Click Google Map and Get current Current Location latitude and longitude Show All Geo-fence Show All Geo-fence on Google Map Clear All Geo-fence Clear All Geo-fence on Google Map...
5.4.1.4 Advanced Operations The Interface for people who know JT600 protocol well. You can send any ASCII command in protocol on this interface. - 25 -...
Item Parameter(e.g.) Explain Note ASCII command Please read JT600 protocol carefully. Send Send this command Clear Clear the below commands records Save all records to PC It’s useful for engineer to Save analysis your Operations. 5.5 Location Short Message format GPS data is sent via SMS.
Google map link. Click this link to view fix location via mobile phone; 2)If GPS signal is invalid, JT600 repies CELL ID and LAC. CELL ID and LAC are got from Base station and showed in decimal system.
Page 28
APN username. If it’s blank. no need input it. Parameter[6]: APN pass APN password. If it’s blank. no need input it. (P08,1,1,11323.1234,2312.2321,11326.4312,2308.1233,area Enquire/Set Parameter[1]: means setting, means enquiring Geo-fence Parameter[2]: means Geo-fence ID.JT600 supports 64 fences. Parameter[3]: 11323.1234,2312.2321,11326.4312,2308.1233 means - 28 -...
Page 29
(P12,0,480) / (P12,0) Parameter[1]: means setting, means enquiring Enquire/Set time Parameter[2]: means 60*8=480 minutes. 480 is example. difference JT600 outputs Greenwich time. So It must be adjusted to local time. (P13,1,1) (P13,1,0) Require SOS LED flashing Parameter[1]: means setting, means enquiring...
Page 30
1 to 7. 1 indicates minimum volume. 7 indicates maximum volume. (P15,13919192020) Require Listen-in Parameter[1]: 13919192020 means cell phone number. After you send this remotely command ,JT600 will call this number. Enquire current (P16) battery (P17,1,jointech) Enquire/Set another Parameter[1]: means setting,...
5.6.2 Short Message Command Example Send Short message Feature Command format example Reply message from JT600 command via cell phone Set SMS (P03,1,13504562154) Primary // SMS Primary number number CALLⅠnumb (P11,1,1,15017935411) - 31 -...
Page 32
Set CALL Ⅱ (P11,1,2,15014059956) number John ,09-28 12:11:02,Speed:32km/h, Battery:80%,GPS:13,STANDARD, http://maps.google.com/?q=22.549737N,114.0766 Enquire current (P02) position (P12,1,480) Set time //GMT +8 difference 8*60=480 minutes in china - 32 -...
Page 33
(P10,1,20) Set Low battery alert //20% Set Another (P17,1,John) name Listen-in (P15,15017935411) remotely The following commands are used for real-time monitoring setting. Data transmission via GPRS. - 33 -...
Page 34
Set SMS (P03,1,13504562154) Primary // SMS Primary number number (P07,1,1) Set working (P07,1) mode //Standard mode (30000000001,P05,211.154.136.219,8888,cmne (P05,1,211.154.136.219,8888,cmnet, t,,) //cmnet Set IP address GPRS APN in china and APN The whole command: parameter (P05,1,211.154.136.219,8888,APN,A PN user,APN pass) Set Data (30000000001,P04,60,0,1) (P04,1,60,0,1) uploading //upload GPS data every 60 seconds...
Worm start 38 seconds,average Hot start 1 second,average Accuracy Position : 10 meters,2D RMS 5 meters,2DRMS,WAAS enabled Velocity : 0.1m/s Time : 1us synchronized to GPS time Maximum < 18,000 meter Altitude Maximum < 515 meter/second Velocity Maximum < 4G Acceleration Update Rate DGPS...
Page 37
Temperature range Normal operation : -20~+55℃ Restricted operation : -25~+70℃ GPRS data downlink transfer: max. 85.6 kbps Data GPRS GPRS data uplink transfer: max. 42.8 kbps Coding scheme: CS-1, CS-2, CS-3 and CS-4 SIM900 supports the protocols PAP (Password Authentication Protocol) usually used for PPP connections.
Supported phonebook types: SM, FD, LD, RC, ON, MC Phonebook management Supports SAT class 3, GSM 11.14 Release 98 SIM Application Toolkit Implemented Real time clock Programmable via AT command Timer function Firmware upgradeable over serial interface Firmware upgrade Ⅶ Standard package and optional accessories Item Accessories name Unit...
1. The unit can only be powered on whiles SIM card put in. The unit will powered off as soon as the SIM card pulled out. 2. If you connected the upgrade cable with JT600,It would be shutdown. To power on the unit, you have to pull and plug SIM card and press power button once.
Page 40
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S.
Need help?
Do you have a question about the JT600 and is the answer not in the manual?
Questions and answers