Magnavox ZV427MG9 Owner's Manual page 31

4
Use [K / L] or [the Number buttons]
to enter the starting and ending
time, then press [B].
Timer Programming
Date Start
Date Start
New Program
JAN/02 12 : 00AM
E1/E2 REC To
E1 DVD
5
Use [K / L] to select the appropriate
external input position (E1/E2) to
which your external tuner is
connected, then press [B].
Timer Programming
Date Start
Date Start
New Program
JAN/02 12 : 00AM
E1/E2 REC To
E1 DVD
6
Use [K / L] to select a recording
media ("DVD" or "VCR"), then press
[B].
Date Start
Date Start
New Program
JAN/02 12 : 00AM
E1/E2 REC To
E1 DVD
7
Use [K / L] to select a recording
mode.
Date Start
Date Start
New Program
JAN/02 12 : 00AM
E1/E2 REC To
E1 DVD
Refer to "Recording Mode" on page 24 for DVD
or "Recording" on page 79 for VCR.
• You can check the remaining recordable space
of the disc when you select the recording mode.
Date Start
JAN/02 12 : 00AM
E1/E2 REC To
E1 DVD
TIMER RECORDING
TUE JAN/01 11:00AM
End E1/E2
End
- - : - -
Mode
SP
SP 2 : 00
1/1
TUE JAN/01 11:00AM
End E1/E2
End
1 : 00AM
Mode
SP
SP 1 : 00
1/1
End E1/E2
End
1 : 00AM
Mode
SP
SP 1 : 00
1/1
End E1/E2
End
1 : 00AM
Mode
SP
SP 1 : 00
1/1
End
1 : 00AM
Mode
SP
SP 1 : 00
Auto recording mode select...(DVD only)
When "Auto" is selected as a recording mode, the unit
calculates how much time is available on the disc and
determines the appropriate recording mode to
complete recording the program.
Date
JAN/02
E1/E2
E1
• "Auto" is only available for one program in the timer
program list.
• The recording may be cut short when the available
recording space of the disc is too limited.
8
Press [OK] when all items are entered.
Your program setting is now stored.
• To set another program, repeat steps 2 to 7.
• To exit, press [TIMER] or [SETUP].
• When 2 or more programs are overlapped,
"Timer program overlapped" appears, and the
overlapped program will be displayed in blue.
• To correct the timer program refer to
"Checking, canceling, or correcting the timer
programming information" on page 30.
9
Press [TIMER SET] to set a timer
programming.
will appear on the front panel display.
BS CS
"VCR" will appear if VCR timer recording have
been set.
Note
• If you have not set the clock yet:
"Clock Setting" menu will appear instead of the timer
programming list at step 1. Continue with the step 4
in "Clock Setting" on page 23 before setting a timer
programming.
• Use [s / B] to move the cursor to the left and the
right in "Timer Programming" menu.
• If a basic recording or one-touch timer recording is in
progress on one component (e.g., VCR) and the timer
recording set for the other component (e.g., DVD) is
about to begin, the unit automatically switches to the
programmed channel for timer recording 2 minutes
before the programmed starting time, and the
recording in progress (for VCR) will be canceled
UNLESS their recording channels are the same. If their
recording channels are the same, the timer recording
will start without canceling the recording currently in
progress. In this case, the recording of the same
channel will be made on both DVD and VCR.
• Cancel the timer-standby mode by pressing
[TIMER SET] before operation for either DVD or VCR.
When finished operating, press [TIMER SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which is
not currently timer-programmed.
Start End
12 : 00AM 1 : 00AM
REC To Mode
DVD Auto
Auto 0 : 00
DR CD
HDD
DVD
EN EN 29 29