Table of Contents
Advertisement
Instructions for use
GB
English,1
RPD 9467 J
Contents
Installation, 2-3-4-5
Connecting the electricity and water supplies
Cutting off the water or electricity supply
Troubleshooting, 13-14
WASHING MACHINE
GB
1
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Hotpoint RPD 9467 J
Summary of Contents for Hotpoint RPD 9467 J
-
Page 1: Table Of Contents
Checking the water inlet hose Precautions and tips, 7 General safety Disposal Opening the porthole door manually Description of the washing machine, 8-9 RPD 9467 J Control panel Display Running a wash cycle, 10 Wash cycles and functions, 11 Table of wash cycles... -
Page 2: Installation
Installation ! Keep this instruction manual in a safe place 2. If the floor is not perfectly level, compensate for future reference. Should the appliance be for any unevenness by tightening or loosening the adjustable front feet (see figure); the an- sold, transferred or moved, make sure the gle of inclination, measured according to the instruction manual accompanies the washing... -
Page 3: Connecting The Drain Hose
Connecting the drain hose • the supply voltage is included within the values indicated on the Technical Data Plate Connect the drain fixed on the machine. hose, without ben- • the socket is compatible with the washing ding it, to a draining machine’s plug. -
Page 4: The First Wash Cycle
13 amp fuse, either in the plug or adaptor or at the distribution board. Technical data If you are in any doubt regarding the electrical supply to your machine, consult a qualified RPD 9467 J Model electrician before use. How to connect an alternative plug: width 59.5 cm... -
Page 6: Care And Maintenance
Care and maintenance Cutting off the water and electri- Cleaning the pump city supplies The washing machine is fitted with a self-clea- • Turn off the water tap after every wash cycle. ning pump which does not require any mainte- This will limit wear on the hydraulic system in- nance. -
Page 7: Precautions And Tips
Precautions and tips Opening the porthole door manually This washing machine was designed and constructed in accordance with international safety regulations. The fol- In the event that it is not possible to open the porthole lowing information is provided for safety reasons and must door due to a powercut, and if you wish to remove the therefore be read carefully. -
Page 8: Description Of The Washing Machine
Description of the washing machine MULTI RINSE Control panel DIRECT FUNCTION button INJECTION buttons ON/OFF button button DISPLAY START/PAUSE AUTO button with indicator light CLEAN Programme KEY LOCK button WASH button Detergent dispenser drawer CYCLE DELAY TEMPERATURE SELECTOR (DELAY KNOB button TIMER) button... - Page 9 Display The display is useful when programming the machine and provides a great deal of information. The following will appear in area A: the icon and selected washing programme, the washing phases and time remaining to the end of the wash cycle. Area B will include the two intensity levels relative to the DIRECT INJECTION option.
-
Page 10: Running A Wash Cycle
1. SWITCH THE MACHINE ON. Press the On/Off good level of antiallergic protection is achieved. Press button ; the text HOTPOINT will appear on the display the button again to go back to the “Normal rinse” rinse and the START/PAUSE indicator light will flash slowly in type. -
Page 11: Wash Cycles And Functions
Wash cycles and functions Table of wash cycles Detergents Max. Max. Description of the wash cycle temp. speed (°C) (rpm) DAILY CLEAN Anti-Stain Power 20°C 20° 1400 20° 1200 Anti-Stain Turbo 45’ (Max. 40°C) 40° Cotton: lightly soiled resistant and delicate colours. 1400 ... -
Page 12: Detergents And Laundry
Detergents and laundry Detergent dispenser drawer label and those issued by the manufacturer of this washing machine (M1127) Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause a build up on the inside of your appliance and contribute to environmental pollution. -
Page 13: Troubleshooting
Troubleshooting Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make sure that the problem cannot be solved easily using the following list. Problem: Possible causes / Solutions: The machine does not switch on. •... - Page 14 The machine is noisy. • There will always be some motor, pump and drum noise during spin. The machine wont spin properly. • Out of Balance detected when attempting to go into a spin cycle - If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly.
-
Page 15: Product Guarantee And Repair Information
Product Guarantee and Repair Information Guarantee Recycling and Disposal Information As part of Hotpoint’s continued commitment to 12 Months Parts and Labour Guarantee helping the environment, Hotpoint reserves the right Your appliance has the benefit of our manufacturer’s to use quality, recycled components to keep down guarantee, which covers the cost of breakdown customer costs and minimise material wastage. - Page 16 195134505.00 05/2015 - Xerox Fabriano Indesit Company Spa Viale Aristide Merloni, 47 60044 Fabriano (AN) Italy www.hotpoint.co.uk...
Need help?
Do you have a question about the RPD 9467 J and is the answer not in the manual?
Questions and answers
F 6? A porta não abre
The document does not specify the meaning of error code F6. The door may not open because the door lock indicator light is still on. It will not open until this light goes out shortly after the program finishes. If there is no power, manual unlocking is required.
This answer is automatically generated
F06 aparece no ecrã? A porta está trancada
is there a filter in the pump pre chamber