Instructions for use WASHING MACHINE Contents Installation, 2-3-4-5 Unpacking and levelling Connecting the electricity and water supplies English,1 The first wash cycle Technical data Care and maintenance, 6 Cutting off the water and electricity supplies Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose...
Page 2
Installation ! Keep this instruction manual in a safe place 2. If the floor is not perfectly level, compensate for future reference. Should the appliance be for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle sold, transferred or moved, make sure the of inclination, measured according to the instruction manual accompanies the washing...
Page 3
Connecting the drain hose • the supply voltage is included within the values indicated on the Technical Data Plate Connect the drain fixed on the machine. hose, without bending • the socket is compatible with the washing it, to a draining machine’s plug.
As the colours of the wires in the lead may ! The power supply cable must only be not correspond with the coloured markings replaced by an authorised serviceman. identifying the terminals in your plug, proceed as follows: Warning! The company denies all liability if and Connect Green &...
Care and maintenance Cutting off the water and Caring for the door and drum of electricity supplies your appliance • Turn off the water tap after every wash cycle. • Always leave the porthole door ajar in order This will limit wear on the hydraulic system to prevent unpleasant odours from forming.
Precautions and tips Opening the porthole door manually This washing machine was designed and constructed in accordance with international safety regulations. The In the event that it is not possible to open the porthole following information is provided for safety reasons and door due to a powercut, and if you wish to remove the must therefore be read carefully.
Description of the washing machine DIRECT Control panel INJECTION TEMPERATURE button and OPTION indicator light button buttons and indicator lights ON/OFF button DISPLAY START/PAUSE button and indicator SPIN LOCK Detergent dispenser drawer light button WASH button CYCLE SELECTOR DELAY KNOB button Detergent dispenser drawer: used to dispense press the button again;...
Page 9
Display The display is useful when programming the machine and provides a great deal of information. The duration of the available wash cycles and the remaining time of a running cycle appear in section A (the display will show the maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the programme varies depending on the wash load and the settings chosen);...
Running a wash cycle ! If the selected option is not compatible with a previously 1. SWITCH THE MACHINE ON. Press the button; selected one, the indicator light corresponding to the first the START/PAUSE indicator light will flash slowly in a function selected will flash and only the second option will green colour.
Detergents and laundry Detergent dispenser drawer Wool - Woolmark Apparel Care - Green: the wool wash cycle of this machine has been approved Successful washing results also depend on the correct by The Woolmark Company for the washing of wool dose of detergent: adding too much detergent will not garments labelled as “hand wash”...
Troubleshooting Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make sure that the problem cannot be solved easily using the following list. Problem: Possible causes / Solutions: • The appliance is not plugged into the socket fully, or not enough to make contact. The machine does not switch on.
Page 14
The machine is noisy. • There will always be some motor, pump and drum noise during spin. The machine wont spin properly. • Out of Balance detected when attempting to go into a spin cycle - If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly.
Product Guarantee and Repair Information Guarantee Recycling and Disposal Information As part of Hotpoint’s continued commitment to 12 Months Parts and Labour Guarantee helping the environment, Hotpoint reserves the right Your appliance has the benefit of our manufacturer’s to use quality, recycled components to keep down guarantee, which covers the cost of breakdown customer costs and minimise material wastage.
Need help?
Do you have a question about the RSG 845 JX UK and is the answer not in the manual?
Questions and answers