Advertising

Advertising

Server Appliance
INSTALLATION
Installation Guide

Advertising

   Related Manuals for Motorola AirDefence

No related manuals

   Summary of Contents for Motorola AirDefence

  • Page 1

    Server Appliance INSTALLATION Installation Guide...

  • Page 3: Table Of Contents

    Contents 1.0 Introduction ......... 1 1.1 Document Conventions .

  • Page 4: Table Of Contents

    3.7 Step 7: Install the Application and Log into the Appliance GUI . . 13 3.8 Step 8: Use the System Setup Wizard for Initial Configuration . . 19 4.0 Regulatory Information ......25 Waste Electrical and Electronic Equipment (WEEE).

  • Page 5

    MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. AirDefense is a registered trademark of AirDefense, Inc. All other product or service names are the property of their respective owners. © Motorola, Inc. 2008. All rights reserved.

  • Page 7: Document Conventions

    Introduction Introduction The AirDefense server appliance is a true plug-and-play system with a hardened operating system, optimized database, automated database maintenance, and all application software included. The AirDefense server appliance provides a scalable, secure, and manageable solution for enterprises to deploy in a single office or corporate campus.

  • Page 8: Site Preparation

    Server Appliance Installation Guide 1.2 Warnings Read all installation instructions and site survey reports, and verify correct equipment installation before • connecting the appliance to its power source. Remove jewelry and watches before installing this equipment. • Verify that the unit is grounded before connecting it to the power source. •...

  • Page 9: Getting Started

    Getting Started Getting Started This guide provides a pre-installation checklist and instructions for installing the AirDefense Server, accessing the Graphical User Interface (GUI), and performing initial server configuration using the System Setup Wizard. 2.1 Pre-installation Checklist Location & Equipment • Server appliance and box contents •...

  • Page 10: Overview

    Server Appliance Installation Guide Sensor Information • Assign an IP address, subnet mask, and default gateway to each Sensor. 2.2 Overview Getting started with AirDefense Enterprise Server is an eight step process. Each step is described in this book. 1. Install the AirDefense Server appliance. 2.

  • Page 11

    Getting Started CAUTION Use only industry-standard mounting kits when installing the AirDefense Server, as improper mounting may result in hardware failure and hazardous conditions. CAUTION Ensure that the electrical circuit through which the AirDefense Server is powered can safely accommodate a 250 Watt power supply for the Model 1250 / 3650 appliance or a 500 Watt power supply for the Model 4250 appliance.

  • Page 12: Installation Steps

    Server Appliance Installation Guide Installation Steps 3.1 Step 1: Install the AirDefense Server Appliance The first step in deploying AirDefense Enterprise is to physically install the appliance in a rack and connect the cables. 1. Install the AirDefense Server in an equipment rack using the rails provided. 2.

  • Page 13: Step 2: Power Up The Appliance

    Installation Steps Which Ethernet port do I use for appliance network connectivity? There are various AirDefense Enterprise server models and the back panels differ slightly. The AirDefense Enterprise application uses Eth0, which corresponds to Ethernet 0 or 2 on a dual Intel NIC, and Ethernet 1 on a dual Broadcom NIC.

  • Page 14

    Server Appliance Installation Guide Model 1250 / Model 3650 Appliance (Front View) Model 4250 Appliance (Front View) NOTE The 2U has a redundant Power Supply and if only one Power Supply is working or plugged in, the alarm will sound. You can reset the power supply alarm by pressing the red button on the back of the appliance.

  • Page 15: Step 3: Launch The Command Line Interface (wipsadmin)

    Installation Steps 3.3 Step 3: Launch the Command Line Interface (WIPSadmin) You must use the server's Command Line Interface (CLI) to configure three initial settings: • Time settings • IP settings • One GUI administrator account. Other configuration activities can occur either on the GUI or the CLI. AirDefense, Inc. recommends that you use the GUI.

  • Page 16

    Server Appliance Installation Guide Alternative A: Specify the time zone and time 1. Type at the prompt, and then press Enter The Time zone screen displays a list of global regions. 2. Type the number that corresponds to your region name, and then press Enter A list of nations within the region displays.

  • Page 17: Step 5: Configure The Ip Address (ip)

    Installation Steps 3.5 Step 5: Configure the IP Address (IP) Set the IP address, subnet mask, and gateway of the AirDefense Server. DHCP is enabled by default. 1. At the command prompt on the WIPSadmin main screen, type , and then press Enter The Config screen displays.

  • Page 18: Step 6: Create A User With Admin Privileges (webu)

    Server Appliance Installation Guide 3. Type a new IP address, and then press Enter 4. Type a new subnet mask, and then press Enter 5. Type a new gateway address, and then press Enter 6. Type to save these settings, and then press Enter 7.

  • Page 19: Step 7: Install The Application And Log Into The Appliance Gui

    Installation Steps 6. Type the user name, and then press Enter 7. Type , and then press admin Enter 8. Type a password, press , type it again to confirm, and then press Enter Enter 9. Type , press twice. Enter 10.

  • Page 20

    Server Appliance Installation Guide 2. Under the Downloads section, select the version of the installation program that corresponds to your OS. A File Download window displays. From this window, you can run the installer now, or save the installation file to your workstation and run it later.

  • Page 21

    Installation Steps 4. Read the license agreement, and then click I Agree The installation location window displays. 5. Accept the default location or browse to another location, and then click Install The installation program installs the AirDefense application, and then displays the finish screen.

  • Page 22

    Server Appliance Installation Guide 6. To start the application, leave the Run AirDefense checkbox selected. To create a shortcut on your desktop, leave the checkbox selected, and then click Finish The AirDefense Enterprise log in screen displays.

  • Page 23

    Installation Steps 7. Log in as the admin user you created earlier or use the credentials from your shipment notification email. The following screen displays. This is the Master License Agreement for the AirDefense System. It will only display when you access the GUI after an installation.

  • Page 24

    Server Appliance Installation Guide This screen will only display the first time you log in after an installation or the first time you log in after a system backup. You have three options: Configure using the Startup Wizard ? this option will start the System Startup Wizard •...

  • Page 25: Step 8: Use The System Setup Wizard For Initial Configuration

    Installation Steps 3.8 Step 8: Use the System Setup Wizard for Initial Configuration The AirDefense Enterprise GUI includes a System Setup wizard that guides you through typical settings required for an effective AirDefense system configuration. All configuration steps are optional and can be finished at any time. The System Setup wizard starts automatically after you install or upgrade the system.

  • Page 26

    Server Appliance Installation Guide 3. Enable policy-based termination—You can select the Enable policy-based termination checkbox to allow users with admin privileges to create policies that automatically terminate wireless devices based on specific alarms or policy violations. 4. Enable port suppression—You can select the checkbox to allow Enable port suppression users to suppress communication on the network switch port that a device is using to...

  • Page 27

    Installation Steps To edit a user account: 1. Select the account in the list. 2. Click Edit 3. Edit the user account settings. 4. Click To delete a user account: 1. Select the account in the list. 2. Click [ Delete You can make additional changes to User Accounts by selecting >...

  • Page 28

    Server Appliance Installation Guide Select the pre-defined Security Sensitivity mode that best suits your organization, and then click if you want to customize it. Pre-defined modes include: Advanced • Monitored WLAN—generally for networks where both performance and security are concerns •...

  • Page 29: Configure Actions

    Installation Steps Configure Actions Configure Action Rules that respond to alarms in your system with a predetermined action. Actions Rules are also defined in the Action Manager. Alternative navigation: > > Configuration Configuration Wizard Configure Actions To add an Action Rule: 1.

  • Page 30

    Server Appliance Installation Guide Import Devices You can import a list of access points or stations, including device information, from an external file. Alternative navigation: > > Import Devices Configuration Configuration Wizard 1. To import a file, select Load AP File Load Station File 2.

  • Page 31: Regulatory Information

    This regulatory section applies to the Motorola AirDefense Solutions server appliances. For more information refer to section 5, Part Numbers, Support, and Sales. All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.

  • Page 32

    Statement of Compliance Motorola hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC, 2006/95/EC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/.

  • Page 33: Waste Electrical And Electronic Equipment (weee)

    Regulatory Information Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Symbol for recycling. For information on how to return product, please go to: http://www.symbol.com/environmental_compliance. Dansk: Til kunder i EU: Alle produkter skal returneres til Symbol til recirkulering, når de er udtjent.

  • Page 34

    Server Appliance Installation Guide Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Symbol al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.symbol.com/ environmental_compliance.

  • Page 35: Part Numbers, Support, And Sales

    • Model number or product name • Software type and version number Motorola responds to calls by email, telephone or fax within the time limits set forth in support agreements. If you purchased your Enterprise Mobility business product from a Motorola business partner, contact that business partner for support.

  • Page 36: Airdefense System

    Server Appliance Installation Guide Master License Agreement for the AirDefense System IMPORTANT—THIS MASTER LICENSE AGREEMENT (THIS "AGREEMENT") GOVERNS THE USE OF THE AIRDEFENSE SYSTEM. READ THIS MASTER LICENSE AGREEMENT CAREFULLY PRIOR TO USING THE AIRDEFENSE SYSTEM (OR ANY PORTION THERETO). IN ORDER TO USE THIS AIRDEFENSE SYSTEM (OR ANY PORTION THERETO), YOU MUST INDICATE YOUR ACCEPTANCE OF THIS AGREEMENT, AND THE ACCEPTANCE OF THE CORPORATE OR BUSINESS ENTITY WHICH PURCHASED THE AIRDEFENSE SYSTEM (the "Licensee"), TO THESE TERMS AND CONDITIONS BY CLICKING ON THE "Accept"...

  • Page 37

    Master License Agreement for the AirDefense System suppliers warrants that the functions or features contained in the Products will meet Licensee's requirements or that the operation of the Products will be uninterrupted or error free. EXCEPT AS PROVIDED HEREIN, THE PRODUCTS ARE BEING PROVIDED "AS IS" WITHOUT ANY WARRANTY OF ANY KIND. AIRDEFENSE AND ITS SUPPLIERS HEREBY DISCLAIM ALL WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, WITHOUT LIMITATION, ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES AS TO NON-INFRINGEMENT RELATED TO THE PRODUCTS PROVIDED HEREUNDER.

  • Page 38

    Server Appliance Installation Guide subject to a Infringement Claim, AirDefense's obligations under this Section shall be fulfilled if at any time AirDefense, in its sole discretion, shall: (x) obtain a license for Licensee to continue to use or to sell the Product purchased from AirDefense;...

  • Page 40

    MOTOROLA INC 1303 E. ALGONQUIN ROAD SCHAUMBURG, IL 60196 http://www.motorola.com Revision A January 2009...

Comments to this Manuals

Symbols: 0
Latest comments: