Related Manuals for KanexPro SP-HDBT1X4
Summary of Contents for KanexPro SP-HDBT1X4
- Page 1 SP-HDBT1X4 4K HDBaseT Splitter 1x4 With PoE All Rights Reserved Version: 4K HDBaseT Splitter 1x4 with PoE_2014V1.0...
-
Page 2: Safety Precautions
SP-HDBT1X4 SAFETY PRECAUTIONS To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference. l Unpack the equipment carefully and save the original box and packing material for possible future shipment l... - Page 3 SP-HDBT1X4 NOTICE: Pictures shown in this manual are for reference only; different model and specifications are subject to real product. The item PoE/ PoC is short for Power over Ethernet or Cable. The receiver works with HDBaseT Splitter can only be HDMI Twisted Pair PoC Receiver.
-
Page 4: Table Of Contents
SP-HDBT1X4 Contents 1. Introduction ........................1 1.1 Introduction to SU4HT ..................1 1.2 Features ......................1 1.3 Package List ...................... 1 2. Panel Description ......................2 2.1 Front Panel ......................2 2.2 Rear Panel ......................3 ... -
Page 5: Introduction
1. Introduction 1.1 Introduction to HDBaseT Splitter The KanexPro SP-HDBT1X4 is an HDBaseT Splitter accepting 1 HDMI input and distributing to 4 HDBaseT outputs, plus 1 HDMI local output. The HDMI output can be used to monitor local displays or cascade up to 4 times with additional HDBaseT splitter It allows uncompressed 4K (max) HDMI, IR, and RS232 signals to be transmitted over a single CAT5e/6/7 cable up to 60m. -
Page 6: Panel Description
SP-HDBT1X4 Ø 1 x Power Adapter (DC 24V) Ø 1 x User Manual Notes： Please confirm if the product and the accessories are all included, if not, please contact with the dealers. 2. Panel Description 2.1 Front Panel Name Description... -
Page 7: Rear Panel
SP-HDBT1X4 LINK: indicate linking status of the four HDBT outputs, corresponding to the four HDBT sockets separately Ø illuminate green when the corresponding HDBaseT output is connected to HDBASE70POER successfully Ø turn off when there is no HDBASE70POER connected to the correspongding socket. -
Page 8: System Connection
SP-HDBT1X4 IR receivers to transmit HDMI signal Ø IN: Connect with IR Receiver to receive IR signal from IR Emitter. Ø LOOP: Cascade IR control signal to another HDBT Splitter by connecting to its IR IN socket Ø OUT: Connect with IR emitter to emit the IR signal received from the receiver side. -
Page 9: System Diagram
SP-HDBT1X4 3.2 System Diagram 3.3 Connection Procedure Step1. Connect a HDMI source device (e.g. Blue-ray DVD) to the HDMI INPUT socket of HDBaseT Splitter with HDMI cable. Step2. Connect a HDMI display to HDMI OUTPUT socket of HDBaseT Splitter with HDMI cable. -
Page 10: Cascade Connection
SP-HDBT1X4 IR LOOP socket of one of them and the IR IN socket of the next until all HDBaseT Splitters have been connected. Step6. Connect a DC 24V power adapter to the power port of HDBaseT Splitter; HDBaseT Splitter can supply power to the HDMI Twisted Pair PoE Receiver with PoE solution. - Page 11 SP-HDBT1X4 Ø Cascade through IR Loop Connect the IR LOOP socket of the first HDBaseT Splitter and the IR IN socket of the next until all HDBaseT Splitter have been connected. Sending IR signals to the IR Receiver connected to the first HDBaseT Splitter will control all cascaded HDBaseT Splitter.
-
Page 12: Twisted Pair Cable Connection
SP-HDBT1X4 3.5 Twisted Pair Cable Connection The twisted pair used in Twisted Pair PoC Receiver MUST is a straight-through cable. The connectors can be T568A or T568B, but both sides must be the same. TIA/EIA T568B TIA/EIA T568A Cable color... -
Page 13: Control Local Device From Remote
SP-HDBT1X4 Figure 4- 1 Control far-end device from local 4.1.2 Control local device from remote Control HDBaseT Splitter or local device from local via corresponding IR remote. -
Page 14: Rs232 Control
SP-HDBT1X4 Figure 4- 2 Control local device from remote 4.2 RS232 Control As RS232 can be transmitted bi-directionally between HDBaseT Splitter and Twisted Pair PoC Receiver, so it is able to control a third party RS232 device from local or control HDBaseT Splitter from remote. - Page 15 SP-HDBT1X4 Parameter Configuration area Monitoring area indicates if the command sent works. Command Sending area Please set the parameters of COM number, bound rate, data bit, stop bit and the parity bit correctly, and then you are able to send command in Command Sending Area.
-
Page 16: Control Far-End Device From Local
SP-HDBT1X4 Note: To control HDBaseT Splitter via RS232 port, the communication protocol parameters should be configured in the right manner: Baud rate: 9600; Data bit: 8; Stop bit: 1; Parity bit: none. 4.2.3 Control far-end device from local Connect the RS232 ports of HDBaseT Splitter and Twisted Pair PoC Receiver (See Figure 4-3), and then it is capable to control HDBaseT Splitter and far-end device from local by sending RS232 commands. -
Page 17: Edid Management
SP-HDBT1X4 Figure 4- 4 Control local device from remote 4.3 EDID Management HDBaseT Splitter provides with a 4-pin EDID DIP switcher, “1” stands for “On”, “0” stands for “Off”. Dial the switches to change EDID data refering to the following... -
Page 18: Specification
SP-HDBT1X4 Switcher Status EDID information 0000 (default) pass through, auto process 0001 1080P 2D 0010 1080P 3D 0011 720P 2D 0100 720P 3D 0101 DVI 1920x1080 Note: EDID data is subject to change in further firmware versions. Please refer to the details of further updated firmware. -
Page 19: Panel Drawing
SP-HDBT1X4 6. Panel Drawing... -
Page 20: Troubleshooting & Maintenance
7. Troubleshooting & Maintenance Problems Causes Solutions Color losing or no video The connecting cables may Check whether the cables signal output in HDMI not be connected correctly are connected correctly display or it may be broken. and in working condition. No HDMI signal output in HDBaseT Splitter while local HDMI input is in... -
Page 21: After-Sales Service
8. After-sales Service If there appear some problems when running the device, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty. 1) Product Limited Warranty: It is warranted that the product will be free from defects in materials and workmanship for one year, which starts from the first day you buy this product (The purchase invoice shall prevail). - Page 22 Product that does not meet this Limited Warranty and which is returned to KanexPro with a copy of customers’ receipt. This Limited Warranty is void if failure of the Product has resulted from accident, abuse, or misapplication.
- Page 23 Brea, California KanexPro.com MPN: SP-HDBT1X4 HDMI® and HDBaseT™ are trademarks or registered trademarks of HDMI Licensing LLC & HDBaseT Alliance respectively in the United States and other countries. KanexPro is a trademark of Apogee Inc., registered trademarks in the US.
Need help?
Do you have a question about the SP-HDBT1X4 and is the answer not in the manual?
Questions and answers