Datalogic Skorpio User Manual

Datalogic Skorpio™ Single Cradle Ethernet
Read this manual carefully before performing any type of
connection from the terminal to a host PC using the
Datalogic Skorpio™ Single Cradle Ethernet.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
NOTE
indication supplied in this manual.
Do not attempt to disassemble the Datalogic Skorpio™
Single Cradle Ethernet, as it does not contain parts that
can be repaired by the user. Any tampering will invalidate
the warranty.
NOTE
The Datalogic Skorpio™ Single Cradle Ethernet paired with a Datalogic
Skorpio™ mobile computer builds a reading system for the collection,
decoding and transmission of barcoded data.
The Datalogic Skorpio™ Single Cradle Ethernet is both a USB and an
Ethernet communication adapter between the host computer and the
Datalogic Skorpio™ mobile computer.
The Datalogic Skorpio™ Single Cradle Ethernet also functions as a
battery charger, both for the mobile computer and the spare battery pack.
The spare battery can be charged by inserting it into the slot at the back
of the cradle.
Power supply is required for Datalogic Skorpio™ mobile computer to be
connected to the cradle and for battery recharging operations.
A
C
B
F
Figure 1 – Datalogic Skorpio™ Single Cradle Ethernet General View
Key:
A) Contacts for Datalogic Skorpio™ Mobile computer
B) Communication status LED
C) Battery charge status LED
D) Ethernet port with integrated Link and Speed LEDs
E) USB connector
F) Power supply connector
G) Spare battery slot
H) Switch Ethernet/USB
822000860
Correct Mobile Computer Insertion/ Removal
For correct insertion into the cradle, insert the mobile computer from the
top of the cradle and push it down until the clip of the cradle clicks. If you
are using a Datalogic Skorpio™ model, release the backstrap from the
bottom side before inserting it into the cradle.
To remove the mobile computer from the cradle, simply pull it upwards
while holding the cradle firmly down.
CONNECTIONS
Ethernet communication requires Datalogic Skorpio™ SW
version 5.41
tapping on Software – Version in the Datalogic default
home page. Otherwise, search for the file version.htm
under the Windows folder.
NOTE
Connections should always be made with power OFF!
G
CAUTION
H
E
During switch operation from Ethernet position to USB
position and vice versa the mobile computer must not be
inserted in the cradle.
D
NOTE
Each connection requires a power supply to be connected to the
cradle. We recommend the DL FPS18 power supply.
1
3.XX SW versions are later than 5.XX Sw versions
Figure 2 - Mobile Computer Insertion
1
or later. Verify the software version by
+
-
Figure 3 - Power Supply Polarity
USB Connection
Be sure that the switch is in the "USB" position.
Connect the single cradle Ethernet to the host by means of any USB
straight cord, such as Datalogic CAB-381 cable.
Insert the power supply plug into the power jack on the back of the cradle
and attach the power supply to a power outlet. Once the host has been
turned on, insert the Datalogic Skorpio™ mobile computer into the cradle.
A
C
B
D
Figure 4 - USB Connection
Key:
A) Host computer
B) 94A051017 CAB-381 USB Type A-B straight cable
C) Datalogic Skorpio™ Single Cradle Ethernet
D) 94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
Ethernet Connection
Be sure that the switch is in the "Ethernet" position.
Connect the Ethernet cradle (Ethernet port ) to an Ethernet hub or a port
on the host device.
Insert the power supply plug into the power jack on the back of the cradle
and attach the power supply to a power outlet. Once the host has been
turned on, insert the Datalogic Skorpio™ mobile computer into the cradle.
A
C
B
Figure 5 – Ethernet Connection
Key:
A) Datalogic Skorpio™ Single Cradle Ethernet
B) 94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
C) UTP CAT 5E cable (recommended use)
D) Ethernet hub
D