1. Manuals
  2. Brands
  3. Protech Systems Manuals
  4. Touch Panel
  5. PPC-7365F
  6. User manual

Protech Systems PPC-7365F User Manual

Via eden low power 15” panel pc system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER'S
MANUAL
PPC-7365F M1
PPC-7365F
VIA Eden Low Power
15" Panel PC System

Advertisement

Table of Contents
loading

Related Manuals for Protech Systems PPC-7365F

Summary of Contents for Protech Systems PPC-7365F

  • Page 1 USER’S MANUAL PPC-7365F VIA Eden Low Power 15” Panel PC System PPC-7365F M1...
  • Page 2 Copyright Notice PPC-7365F Panel PC System With LCD / Touch screen OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist users in installing and setting up the system. The information contained in this document is subject to change without prior any notice.
  • Page 3 Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 4: Table Of Contents

    Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual ............Case Illustration ............. System Specification ............. Safety and Notification ........... 1-10 CHAPTER 2 SYSTEM CONFIGURATION Jumper & Connector Quick Reference Table ....Component Locations ........... How to Set the Jumpers ..........COM Port Connector …………………………………...
  • Page 5 Contents 2-31 Memory Installation ....………......2-27 2-32 AT/ATX Power Selection ……………………………. 2-28 2-33 Compact Flash Master/Slave Selection ………………. 2-29 2-34 IRQ12 Release Selection ……………………………… 2-29 2-35 LVDS Panel Resolution Selection ……………………. 2-30 2-36 Inverter Connector …………………………………… 2-30 2-37 Power Module ………………………………..………. 2-31 2-38 Compact Flash Connector ……………………………..
  • Page 6 Contents 4-13 Password Setting ..........…..4-26 4-14 Save & Exit Setup ............4-27 4-15 Exit Without Saving ............4-28 APPENDIX A SYSTEM ASSEMBLY Exploded Diagram for HDD Assembly ….…………………… Exploded Diagram for Wall Mounting ….……….…………… Exploded Diagram for VESA ARM ……..……..…………..… APPENDIX B TECHNICAL SUMMARY Block Diagram .................

  • Page 7: Chapter 1 Introduction

    CHAPTER INTRODUCTION This chapter gives you the information for PPC-7365F. It also outlines the System specifications. Section includes: About This Manual Case Illustration System Specifications Safety precautions Experienced users can skip to chapter 2 on page 2-1 for a Quick Start.

  • Page 8: About This Manual

    This chapter indicates on how to set up the BIOS configurations. Appendix A System Assembly This section gives you the exploded diagram for the whole system unit. Appendix B Technical Summary This section gives you the information about the Technical maps. ′ Page: 1-2 PPC-7365F USER S MANUAL...

  • Page 9: Case Illustration

    Chapter 1 Introduction 1-2. CASE ILLUSTRATION ′ Page: 1-3 PPC-7365F USER S MANUAL...

  • Page 10: System Specification

    Phoenix-Award Flash BIOS for plug & play function. Memory size with 2MB and with VGA BIOS. Support S I/O Setup. KEYBOARD CONNECTOR : Mini DIN connector. Supports PC/AT Keyboard. MOUSE CONNECTOR : Mini DIN connector. Supports PS/2 Mouse. ′ Page: 1-4 PPC-7365F USER S MANUAL...
  • Page 11 COM1 contain 5V or 12V power capability with 9-pin D-sub connector on rear panel. COM2/3/4 support 5V power only. PARALLEL PORT : One 25-pin D-Sub connector on rear panel. Support for SPP, ECP, EPP Function. Bi-directional parallel port. ′ Page: 1-5 PPC-7365F USER S MANUAL...
  • Page 12 Some sequential pixels may not light or may light always, but this is not a failure. LCD TYPE : LCD Panel15”: Priority source - or similar model. LVDS PIXEL PITCH : According to the supplier’s LCD specification. BRIGHTNESS : According to the supplier’s LCD specification. ′ Page: 1-6 PPC-7365F USER S MANUAL...
  • Page 13 TOUCH SCREEN : (OPTIONAL) Type Resistive 500g (30 ㎝ , 30 Sec) Static Load Hardness Transparency Write Life 10,000,000 Times Knock Life 35,000,000 Times Chattering Time 10 ms Input Voltage Wire 5 Wire ′ Page: 1-7 PPC-7365F USER S MANUAL...

  • Page 14: General Information

    1x Compact Flash Type-II Slot (IDE, On Board) CONSTRUCTION : Electo Galvanized steel chassis. Aluminium front bezel. DIMENSIONS : 400 x 300 x 123mm (15.75” x 11.81” x 4.85”) NET WEIGHT : 8 kg ′ Page: 1-8 PPC-7365F USER S MANUAL...

  • Page 15: Safety And Notification

    15V~24V, otherwise the system may be damaged. 2. Environmental Conditions a. Place your PPC-7365F on a sturdy, level surface. Be sure to allow enough room on each side to have easy access. b. Avoid extremely hot or cold places to install your PPC.

  • Page 16: Chapter 2 System Configuration

    CHAPTER SYSTEM CONFIGURATION Helpful information that describes the jumper & connector settings, and component locations. Section includes: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector Pin Assignments Page 2-1...

  • Page 17: Jumper & Connector Quick Reference Table

    LVDS Panel Resolution Selection ………………………… JP16 Inverter Connector ………………………………………. INV1 IDE Power Module ………………………………………. POWER1 Compact Flash Connector ………………………………… PC104 Connector …………………………………………. PC104 PC104+ Connector ………………………………………… PC104PLUS1 CPU Fan Connector ………………………………………. FAN1 System Fan Connector ……………………………………. FAN2 Page: 2-2 ’ PPC-7365F USER S MANUAL...

  • Page 18: Component Locations

    Chapter 2 Hardware Configuration 2-2. COMPONENT LOCATIONS PPC-7365F Connector, Jumper and Component locations Page: 2-3 ’ PPC-7365F USER S MANUAL...

  • Page 19: How To Set The Jumpers

    PIN1 & PIN2 to create one setting and shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent. Page: 2-4 ’ PPC-7365F USER S MANUAL...
  • Page 20 Chapter 2 Hardware Configuration JUMPER DIAGRAMS JUMPER SETTINGS Page: 2-5 ’ PPC-7365F USER S MANUAL...

  • Page 21: Com Port Connector

    ASSIGNMENT DCD1 DTR1 COM1 DSR1 RTS1 CTS1 COM2 : COM2 Connector The COM2 Connector assignments are as follows : ASSIGNMENT RS-232 RS-422 RS-485 DCD2 COM2 DTR2 DSR2 RTS- RTS2 RTS+ CTS2 CTS+ CTS- Page: 2-6 ’ PPC-7365F USER S MANUAL...
  • Page 22 The pin assignments are as follows : ASSIGNMENT DCD4 DTR4 DSR4 RTS4 CTS4 All COM port’s pin 9 is selectable for RI, +5V or +12V. For more information, please refer to our “2-5 COM RI and Voltage Selection”. Page: 2-7 ’ PPC-7365F USER S MANUAL...

  • Page 23: Com Port Ri & Voltage Selection

    2-5. COM PORT RI & VOLTAGE SELECTION JP19 : COM1, COM2, COM3, and COM4 RI & Voltage Selection The selections are as follows: JUMPER SETTING JUMPER SELECTION (Pin Closed) ILLUSTRATION (default) 11-13 COM1 9-11 (default) COM2 12-14 10-12 Page: 2-8 ’ PPC-7365F USER S MANUAL...
  • Page 24 Chapter 2 Hardware Configuration (default) COM3 15-17 17-19 (default) COM4 16-18 18-20 Page: 2-9 ’ PPC-7365F USER S MANUAL...

  • Page 25: Rs232/422/485 (Com2) Selection

    The jumper settings are as follows : COM 2 JUMPER SETTING JUMPER ILLUSTRATION FUNCTION (pin closed) RS-232 Open (default) 1-2, 5-6, 7-8, 9-10 11-12, 13-14, 15-16 RS-422 17-18, 19-20 1-3, 4-6, 7-8, 9-10 11-12, 13-14, 15-16 RS-485 17-18, 19-20 Page: 2-10 ’ PPC-7365F USER S MANUAL...

  • Page 26: Vga Connector

    Chapter 2 Hardware Configuration 2-7. VGA CONNECTOR VGA : VGA Connector The pin assignments are as follows: ASSIGNMENT GREEN BLUE VGA IIC DATA HSYNC VSYNC VGA IIC CLK Page: 2-11 ’ PPC-7365F USER S MANUAL...

  • Page 27: Lvds Connector

    2-8. LVDS CONNECTOR LVDS1 : LVDS Connector The pin assignments are as follows : ASSIGNMENT ASSIGNMENT LVDSVCC LVDSVCC LVDS2 : LVDS Connector The pin assignments are as follows : ASSIGNMENT ASSIGNMENT LVDSVCC LVDSVCC Page: 2-12 ’ PPC-7365F USER S MANUAL...

  • Page 28: Brightness Voltage Selection

    Chapter 2 Hardware Configuration 2-9. BRIGHTNESS VOLTAGE SELECTION JP9: Brightness Voltage Selection The selections are as follows : JUMPER SETTING JUMPER SELECTION (Pin Closed) ILLUSTRATION (default) 2.5V Page: 2-13 ’ PPC-7365F USER S MANUAL...

  • Page 29: Lvds Voltage Selection

    Chapter 2 Hardware Configuration 2-10. LVDS VOLTAGE SELECTION JP12: LCD Voltage Selection The selections are as follows : JUMPER SETTING JUMPER SELECTION (Pin Closed) ILLUSTRATION 3.3V (default) Page: 2-14 ’ PPC-7365F USER S MANUAL...

  • Page 30: Power Connector

    Chapter 2 Hardware Configuration 2-11. POWER CONNECTOR CN1: Power Connector The pin assignments are as follows : ASSIGNMENT 5VSB PS_ON -12V Page: 2-15 ’ PPC-7365F USER S MANUAL...

  • Page 31: Floppy Disk Drive Connector

    Chapter 2 Hardware Configuration 2-12. FLOPPY DISK DRIVE CONNECTOR FDD1 : Floppy Disk Drive Connector The pin assignments are as follows: ASSIGNMENT ASSIGNMENT INDEXJ DRVAJ DSKCHGJ MOTEAJ FDIRJ STEPJ DENSELJ WDATAJ WGATEJ TK00J WPTJ RDATAJ SIDE1J Page: 2-16 ’ PPC-7365F USER S MANUAL...

  • Page 32: Hard Disk Drive Connector

    ASSIGNMENT ASSIGNMENT IDERSTJ PDD7 PDD8 PDD6 PDD5 PDD10 PDD4 PDD11 PDD3 PDD12 PDD2 PDD13 PDD1 PDD14 PDD0 PDD15 DDREQA DIOWAJ DIORAJ HDRDYA PULL LOW DDACKAJ IDE_IRQ14 PDA1 PD_80P PDA0 PDA2 PDCSJ1 PDCSJ3 HDLEDJ1 Page: 2-17 ’ PPC-7365F USER S MANUAL...

  • Page 33: Printer Connector

    As to link the Printer to the card, you need a cable to connect both DB25 connector and parallel port. The pin assignments are as follows : LPT1 ASSIGNMENT ASSIGNMENT STROBE AFDJ PPD0 ERRORJ PPD1 INITJ PPD2 SLINJ PPD3 PPD4 PPD5 PPD6 PPD7 ACKJ BUSY SLCT Page: 2-18 ’ PPC-7365F USER S MANUAL...

  • Page 34: Lan Connector

    The pin assignment is as follows : ASSIGNMENT MDI_0P MDI_0N MDI_1P MDI_2P MDI_2N MDI_1N MDI_3P MDI_3N 2-16. LAN LED CONNECTOR LANLED1 : LAN LED Connector The pin assignment is as follows : ASSIGNMENT LED100 CONTROL LED1000 Page: 2-19 ’ PPC-7365F USER S MANUAL...

  • Page 35: Keyboard Connector

    The pin assignments are as follows : ASSIGNMENT KB DATA 5VSB KB CLK 2-18. PS/2 MOUSE CONNECTOR MS1 : PS/2 Mouse Connector The pin assignments are as follows : ASSIGNMENT MS DATA 5VSB MS CLK Page: 2-20 ’ PPC-7365F USER S MANUAL...

  • Page 36: Sound Connector

    The pin assignment is as follows : ASSIGNMENT LINE_L LINE_R MIC1 : Microphone Connector The pin assignment is as follows : ASSIGNMENT MIC_IN1 MIC_IN2 SPK1 : Line-Out Connector The pin assignment is as follows : ASSIGNMENT Line-out-L Line-out-R Page: 2-21 ’ PPC-7365F USER S MANUAL...

  • Page 37: Onboard Audio Selection

    JP17 : Reset Connector Switch. The pin assignment is as follows : ASSIGNMENT RST SW 2-22. HDD LED CONNECTOR HDLED1 : HDD LED Connector The pin assignment is as follows : ASSIGNMENT HD_LED+ HD_LED- Page: 2-22 ’ PPC-7365F USER S MANUAL...

  • Page 38: Power Button

    JP14 (1-2) : External Buzzer Connector. The pin assignments are as follows : ASSIGNMENT E_BUZ_PWR E_BUZ 2-25. EXTERNAL SMI CONNECTOR JP14 (7-8) : External SMI Connector. The pin assignments are as follows : ASSIGNMENT EXTSMIJ Page: 2-23 ’ PPC-7365F USER S MANUAL...

  • Page 39: Clear Cmos Selection

    To clear CMOS data, user must power-off the computer and set the jumper to “Clear CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal” and power-on the computer. Page: 2-24 ’ PPC-7365F USER S MANUAL...

  • Page 40: Universal Serial Bus Connector

    USB2: Universal Serial Bus Connector. The pin assignments are as follows : ASSIGNMENT VCCUSB1 USB1N_R USB1P_R USB2 USB3 : Universal Serial Bus Connector. The pin assignments are as follows : ASSIGNMENT VCCUSB2 USB2N_R USB2P_R Page: 2-25 ’ PPC-7365F USER S MANUAL...

  • Page 41: Reset/Nmi Selection

    Interrupt, is used for serious conditions that demand the processor’s immediate attention, it cannot be ignored by the system unless it is shut off specifically. To clear NMI command, user should short the “Clear Watchdog” pin via push button. Page: 2-26 ’ PPC-7365F USER S MANUAL...

  • Page 42: Wake-On-Lan Connector

    The pin assignments are as follows : ASSIGNMENT PW_LED+ 2-31. MEMORY INSTALLATION This system is enhanced with 1 DDR DRAM banks, which support up to DRAM BANK CONFIGURATION DIMM 1 TOTAL MEMORY 128M 128MB 256M 256MB 512M 512MB Page: 2-27 ’ PPC-7365F USER S MANUAL...

  • Page 43: At/Atx Power Selection

    Chapter 2 Hardware Configuration 2-32. AT/ATX POWER SELECTION JP14 (3-6) : AT/ATX Power Selection The selections are as follows: JUMPER FUNCTION JUMPER SETTING ILLUSTRATION JP14 (3-6) JP18 3-4, 5-6 Open open (default) Page: 2-28 ’ PPC-7365F USER S MANUAL...

  • Page 44: Compact Flash Master/Slave Selection

    JUMPER SETTING ILLUSTRATION Master (default) Slave open 2-34. IRQ12 RELEASE SELECTION JP6 : IRQ12 Release Selection. The selections are as follows: JUMPER SELECTION JUMPER SETTING ILLUSTRATION IRQ12 Release Closed PS/2 Mouse Open (default) Page: 2-29 ’ PPC-7365F USER S MANUAL...

  • Page 45: Lvds Panel Resolution Selection

    FUNCTION ILLUSTRATION (pin closed) 800 x 600 1024 x 768 (default) 2-36. INVERTER CONNECTOR INV1: Inverter Connector. The pin assignments are as follows : ASSIGNMENT VCC12 BRCTR ENVEE (Inverter backlight On/Off control signal) Page: 2-30 ’ PPC-7365F USER S MANUAL...

  • Page 46: Power Module

    Chapter 2 Hardware Configuration 2-37. POWER MODULE POWER1 : Power Module. The pin assignments are as follows : ASSIGNMENT ASSIGNMENT 5VSB 5VSB 5VSB PS-ON -12V +12V -12V +12V -12V +12V Page: 2-31 ’ PPC-7365F USER S MANUAL...

  • Page 47: Compact Flash Connector

    Chapter 2 Hardware Configuration 2-38. COMPACT FLASH CONNECTOR CF1 : Compact Flash Connector. The pin assignments are as follows : ASSIGNMENT ASSIGNMENT CSJ1 CSJ3 SDIORDJ SDIOWRJ IRQ15 -CSEL RESETJ IORDY ACKJ CF_LEDJ -PDIAG Page: 2-32 ’ PPC-7365F USER S MANUAL...

  • Page 48: Pc 104 Connector

    LA18 IRQ14 +12V LA17 DACKJ0 IOCHRDY MEMRJ DREQ0 SMEMWJ MEMWJ DACKJ5 SMEMRJ DREQ5 IOWJ DACKJ6 IORJ DREQ6 DACKJ3 DACKJ7 DREQ3 DREQ7 DACKJ1 DREQ1 MASTERJ REFRESHJ SYSCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 DACKJ2 BALE Page: 2-33 ’ PPC-7365F USER S MANUAL...

  • Page 49: Pc 104+ Connector

    B24 REQJ2 D24 GNTJ0 GNTJ1 B25 NC GNTJ2 D25 GND B26 PCLK1 D26 PCLK2 PCLK3 B27 +5V PCLK4 D27 GND B28 INTDJ D28 RSTJ +12V B29 INTAJ INTBJ D29 INTCJ B30 NC D30 GND Page: 2-34 ’ PPC-7365F USER S MANUAL...

  • Page 50: Cpu Fan Connector

    2-41. CPU FAN CONNECTOR FAN1 : CPU Fan Connector The pin assignments are as follows: ASSIGNMENT +12V CPUFAN1 2-42. SYSTEM FAN CONNECTOR FAN2 : System FAN Connector The pin assignments are as follows: ASSIGNMENT Page: 2-35 ’ PPC-7365F USER S MANUAL...
  • Page 51 CHAPTER SOFTWARE UTILITIES This chapter comprises the detailed information of VGA driver, LAN driver, and sound driver, VIA Chipset Software Installation Utility, touch screen driver, USB 2.0 driver and Flash BIOS update. It also describes how to install the watchdog timer configuration. Section includes: Introduction VIA 4 IN1 Service Pack Driver Utility...

  • Page 52: Introduction

    Chapter 3 Software Configuration 3-1. INTRODUCTION Enclosed with our PPC-7365F package is our driver utility, which may comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user, you will only need some of the files contained in the CD ROM disc,...

  • Page 53: Vga Driver Utility

    3-3. VGA DRIVER UTILITY 3-3-1. Introduction The VGA interface embedded with our PPC-7365F can support a wide range of display mode, such as SVGA, STN, TFT,..etc. You can display CRT and LCD Panel simultaneously on this board, but make sure that the modes for CRT and LCD Panel are the same.

  • Page 54: Flash Bios Update

    3-4. FLASH BIOS UPDATE 3-4-1. Introduction Users of PPC-7365F can use the program “Awdflash.exe” contained in the Utility Disk for system BIOS update. 3-4-2. Installation of system BIOS 1. Copy “Awdflash.exe” from Driver Disk to Drive C.
  • Page 55 Select "Y", and the BIOS will be renewed. When you are refreshing the BIOS, do not turn off or reset the system, or you will damage the BIOS. After you have completed all the programming, the screen displays the table below: ′ Page:3-5 PPC-7365F USER S MANUAL...

  • Page 56: Lan Driver Utility

    Please reset or power off the system, then the Flash BIOS is fully implemented. 3-5. LAN DRIVER UTILITY 3-5-1. Introduction The PPC-7365F Panel PC is enhanced with LAN function that can support various network adapters. Installation programs for LAN drivers are listed as follows: 1.

  • Page 57: Sound Driver Utility

    3-6. SOUND DRIVER UTILITY 3-6-1. Introduction The VT1612A sound function enhanced in this system is fully compatible with Windows 98, Windows NT 4.0, and Windows 2000. Below, you will find the content of the Sound driver : ′ Page:3-7 PPC-7365F USER S MANUAL...
  • Page 58 Click Setup.exe file for USB driver installation. Follow the instructions on the screen to complete the installation. Once installation is completed, shut down the system and restart in order for the changes to take effect. ′ Page:3-8 PPC-7365F USER S MANUAL...

  • Page 59: Touch Screen Driver Utility (Optional)

    I/O port 441H, the system will run the command to stop the Watchdog function. In PPC-7365F watchdog function, you must write your program so when it writes I/O port address 443 for enable watchdog and write I/O port address 441 for disable watchdog.
  • Page 60 Chapter 3 Software Configuration MOV DX, 441H OUT DX, AX The Watchdog Timer control table is as follows: Level Value Time/sec Level Value Time/sec ′ Page:3-10 PPC-7365F USER S MANUAL...
  • Page 61 CHAPTER AWARD BIOS SETUP This chapter shows how to set up the Award BIOS. Section includes: Introduction Entering Setup The Standard CMOS Features The Advanced BIOS Features The Advanced Chipset Features Integrated Peripherals Power Management Setup PNP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults...

  • Page 62: Introduction

    4-1. INTRODUCTION This chapter will show you the function of the BIOS in managing the features of your system. The PPC-7365F Panel PC is equipped with the BIOS for system chipset from Award Software Inc. This page briefly explains the function of the BIOS in managing the special features of your system.

  • Page 63: Entering Setup

    You may use the cursor the up/down keys to highlight the individual menu items. As you highlight each item, a brief description of the highlighted selection will appear at the bottom of the screen. ′ Page: 4-3 PPC-7365F USER S MANUAL...

  • Page 64: The Standard Cmos Features

    < Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the time as 16:30:00. ′ Page: 4-4 PPC-7365F USER S MANUAL...
  • Page 65 Auto: The BIOS automatically determines the optimal mode. Normal: Maximum number of cylinders, heads, sectors supported are 1024, 16 and 63. Large: For drives that do not support LBA and have more than 1024 cylinders. ′ Page: 4-5 PPC-7365F USER S MANUAL...
  • Page 66 BASE MEMORY: Displays the amount of conventional memory detected during boot up. EXTENDED MEMORY: Displays the amount of extended memory detected during boot up. TOTAL MEMORY: Displays the total memory available in the system. ′ Page: 4-6 PPC-7365F USER S MANUAL...

  • Page 67: Chapter 4 Award Bios Setup

    1024 65535 1023 1024 65535 1023 1024 65535 1023 1024 65535 1023 1024 65535 1023 65535 1023 65535 1024 65535 1023 1024 65535 1023 65535 65535 65335 AUTO Award Hard Disk Type Table ′ Page: 4-7 PPC-7365F USER S MANUAL...
  • Page 68 F7:Optimized Defaults BIOS Features Setup Menu The “BIOS FEATURES SETUP” allow you to configure your system for basic operation. The user can select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. ′ Page: 4-8 PPC-7365F USER S MANUAL...
  • Page 69 You may enable / disable this item to define whether the system will look for a floppy disk drive to boot at power-on, or proceed directly to the hard disk drive. BOOT UP NUMLOCK STATUS: Select power on state for NumLock. GATE 20A OPTION: ′ Page: 4-9 PPC-7365F USER S MANUAL...
  • Page 70 Setup freely. OS SELECT FOR DRAM >64MB : Select the operating system that is running with greater than 64MB or RAM on the system. You may choose OS2 or Non-OS2. ′ Page: 4-10 PPC-7365F USER S MANUAL...

  • Page 71: The Advanced Chipset Features

    PCI Master 0 WS Write [Enabled] PCI Delay Transaction [Disabled] PCI#2 Access #1 Retry [Enabled] ↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Chipset Features Setup Screen ′ Page: 4-11 PPC-7365F USER S MANUAL...
  • Page 72 In order to improve performance, certain space in memory is reserved for ISA cards. This memory must be mapped into the memory space below 16MB. P2C/C2P CONCURRENCY: This item allows you to enable/ disable the PCI to CPU, CPU to PCI concurrency. ′ Page: 4-12 PPC-7365F USER S MANUAL...
  • Page 73 When Enabled, every write transaction goes to the write buffer. Burstable transactions then burst on the PCI bus and nonburstable transactions don’t. PCI MASTER 0 WS WRITE : When Enabled, writes to the PCI bus are executed with zero wait states. ′ Page: 4-13 PPC-7365F USER S MANUAL...
  • Page 74 Select Enabled to support compliance with PCI specification version 2.1. PCI#2 ACCESS #1 RETRY : When disabled, PCI#2 will not be disconnected until access finishes (default). When enabled, PCI#2 will be disconnected if max retries are attempted without success. ′ Page: 4-14 PPC-7365F USER S MANUAL...

  • Page 75: Integrated Peripherals

    F6:Fail-Safe Defaults F7:Optimized Defaults Integrated Peripherals Setup Screen By moving the cursor to the desired selection and by pressing the <F1> key, the all options for the desired selection will be displayed for choice. ′ Page: 4-15 PPC-7365F USER S MANUAL...
  • Page 76 Select Enabled if the system has a floppy disk drive (FDD) installed on the system board and you wish to use it. If you install and-in FDD or the system has no floppy drive, select Disabled. ′ Page: 4-16 PPC-7365F USER S MANUAL...
  • Page 77 This field allows you to enable or disable IO channel check NMI. Before selecting this function, the user should check first that NMI function is enabled as described in chapter 2 (Reset/NMI/Clear Watchdog Selection). ′ Page: 4-17 PPC-7365F USER S MANUAL...

  • Page 78: Power Management Setup

    Max. Power Saving mode and stop the CPU internal clock. If Advance Power Management (APM) is installed on your system, selecting Yes gives better power savings. If the Max. Power Saving is not enabled, this will be preset to No. ′ Page: 4-18 PPC-7365F USER S MANUAL...
  • Page 79 Enabled, even when the system is in a power down mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4) Secondary IDE 1 (5) FDD, COM, LPT Port ′ Page: 4-19 PPC-7365F USER S MANUAL...

  • Page 80: Pnp/Pci Configuration

    This section covers technical items, which is strongly recommended for experienced users only. PNP OS INSTALLED: This item allows you to determine install PnP OS or not. ′ Page: 4-20 PPC-7365F USER S MANUAL...
  • Page 81 DMA channel. PCI/VGA PALETTE SNOOP: Leave this field at disabled. ASSIGN IRQ FOR USB: Enable or Disable to assign IRQ for USB. ASSIGN IRQ FOR VGA: Enable or Disable to assign IRQ for VGA. ′ Page: 4-21 PPC-7365F USER S MANUAL...

  • Page 82: Pc Health Status

    This item shows you the current CPU temperature. SYSTEM FAN SPEED: This item shows you the current SYSTEMFAN speed. VCORE: This item shows you the current system voltage. 2.5V/3.3V/5V/12V: This item shows you the voltage of +3.3V/+5V/+12V/-12V/-5V. ′ Page: 4-22 PPC-7365F USER S MANUAL...

  • Page 83: Frequency / Voltage Control

    This setup menu allows you to specify your settings for frequency/voltage control. AUTO DETECT PCI CLK: This item allows you to enable or disable auto detect PCI Clock. SPREAD SPECTRUM: This item allows you to enable or disable the spread spectrum modulate. ′ Page: 4-23 PPC-7365F USER S MANUAL...

  • Page 84: Load Fail-Safe Defaults

    Pressing "Y" loads the default values that are factory setting for optimal performance system operations. Please be aware that if select the wrong panel type, it may cause the abnormal display of the LCD. ′ Page: 4-24 PPC-7365F USER S MANUAL...

  • Page 85: Password Setting

    PASSWORD DISABLED!!! Press any key to continue... Press the < Enter > key again and the password will be disabled. Once the password is disabled, you can enter Setup freely. ′ Page: 4-25 PPC-7365F USER S MANUAL...

  • Page 86: Save & Exit Setup

    You may always call up the setup program at any time to adjust any of the individual items by pressing the <Del> key during boot up. ′ Page: 4-26 PPC-7365F USER S MANUAL...

  • Page 87: Exit Without Saving

    Quit Without Saving (Y/N)? N etup ►PnP/PCI Configura ►PC Health Status Saving Esc : Quit F9 : Menu in BIOS ↑↓→← : Select Item F10 : Save & Exit Setup Abandon all Datas ′ Page: 4-27 PPC-7365F USER S MANUAL...

  • Page 88: Appendix A System Assembly

    APPENDIX SYSTEM ASSEMBLY This appendix contain exploded diagram of the system. Section includes: Exploded Diagram for HDD Assembly Exploded Diagram for Wall Mounting Exploded Diagram for VESA ARM Page: A-1...
  • Page 89 RUBBER (Si 22 green) Dia 11.5x11.5Hx3.5 QWS-2.7-8-1 WASHER 2.7 x 8 x1 WASHER QSTUD-2.5-6-R M2.5x6(ROUND_HEAD) SCREW 20-029-03001029 PPC-7365(F) 2.5IN HDD HOLDER HML-95-68.85-0.125 MYLAY (95x68.85x0.125mm) FOR PS-8830 SLIM HDD SLIM HDD QSTUD-3-0.5-6-SP-W M3xP0.5L=6 QSTUD-UNC-N06-32-FLAT UNC-N06-32-FLAT (No6-32 UNC FLAT L=6.4) ′ Page: A-2 PPC-7365F USER S MANUAL...

  • Page 90: Exploded Diagram For Wall Mounting

    Appendix A System Assembly EXPLODED DIAGRAM FOR WALL MOUNTING STEP 1: PART NO DESCRIPTION Q'TY REMARKS EC-8150A-HOOK-SHEET PS-8150A CASE HOOK SHEET QSTUD-3-0.5-6-F-B Screw M3 x 0.5P x 6 FLAT Black ′ Page: A-3 PPC-7365F USER S MANUAL...
  • Page 91 Appendix A System Assembly STEP 2: Wall ′ Page: A-4 PPC-7365F USER S MANUAL...
  • Page 92 Appendix A System Assembly STEP 3: WALL DESCRIPTION PART NO REMARKS Q'TY EC-M4-HOOK M4 HOOK QSTUD-4-0.7-35-R-N Screw M4 x 0.7P x 35mm QSTUD-4-0.7-NIL Screw hat M4 x 0.7P x 3mm ′ Page: A-5 PPC-7365F USER S MANUAL...
  • Page 93 Appendix A System Assembly STEP 4, 5 & 6: HOOK M4 SCREW M4 NUT (IF NEED) STEP 4 WALL STEP 5 M4 NUT STEP 6 WALL WALL M4 NUT M4 SCREW HOOK ′ Page: A-6 PPC-7365F USER S MANUAL...

  • Page 94: Exploded Diagram For Vesa Arm

    Appendix A System Assembly EXPLODED DIAGRAM FOR VESA ARM DESCRIPTION Q'TY REMARKS PART NO EC-8150A-W-STD 8150A-WALL-MOUNT Screw M4-P0.7-L6 FLAT Black QSTUD-4-0.7-6-F-B ′ Page: A-7 PPC-7365F USER S MANUAL...
  • Page 95 APPENDIX TECHNICAL SUMMARY This section introduce you the maps concisely. Sections include: Block Diagram Interrupt Map RTC (Standard) RAM Bank Timer & DMA Channels Map I / O & Memory Map Page: B-1...

  • Page 96: Appendix B Technical Summary Block Diagram

    Appendix B Technical Summary BLOCK DIAGRAM ′ Page: B-2 PPC-7365F USER S MANUAL...

  • Page 97: Interrupt Map

    Serial port 2 Serial port 1 Available Floppy Disk adapter Parallel port 1 RTC clock ACPI-Compliant System Serial port 3 Serial port 4 PS/2 Mouse Math coprocessor Hard Disk adapter Hard Disk adapter ′ Page: B-3 PPC-7365F USER S MANUAL...
  • Page 98 Second alarm Minutes Minutes alarm Hours Hours alarm Day of week Day of month Month Year Status register A Status register B Status register C Status register D 0Eh-7Fh 114 Bytes of User RAM ′ Page: B-4 PPC-7365F USER S MANUAL...

  • Page 99: Timer & Dma Channels Map

    Timer Channel Map : Timer Channel Assignment System timer interrupt DRAM Refresh request Speaker tone generator DMA Channel Map : DMA Channel Assignment Available Available Floppy Disk adapter Available Cascade Available Available Available ′ Page: B-5 PPC-7365F USER S MANUAL...

  • Page 100: I/O & Memory Map

    RTC Controller NMI & RTC controller RTC RTC Controller RTC Controller RTC Controller NMI & RTC controller RTC RTC Controller RTC Controller RTC Controller NMI & RTC controller RTC RTC Controller RTC Controller ′ Page: B-6 PPC-7365F USER S MANUAL...
  • Page 101 2. Only if IDE Standard I/O space is enabled for Secondary Drive. Otherwise, the target is PCI. 3. If POS_DEC_EN bit is enabled, reads from F0h will not be decoded by the ICH2. If POS_DEC_EN is not enabled, reads from F0h will forward to LPC. ′ Page: B-7 PPC-7365F USER S MANUAL...
  • Page 102 Bit 0 in FWH Decode Enable 2 FF00 0000h-FF0F FFFFh Register is set Anywhere in 4GB range D110 LAN Controller Enable via BAR in Device 29:Function 0 (D110 LAN Controller) All Other None ′ Page: B-8 PPC-7365F USER S MANUAL...

Table of Contents