Technical Specifications - AER Compact Slope User Manual

Hide thumbs

Table Of Contents

Table of Contents

Technical data

6. Technical specifications Compact Slope

Inputs

Inputs (notes 1, 2, 4)

channel 1

High impedance, unbalanced input for

channel 1

instruments (pick-ups) and line-level sources

Mono jack socket, ¼" (6.35 mm)

Sensitivity: 22 mV (–33 dBV)

High/low (attenuator) switch: –10 dB

Impedance: 2.2 Meg

Equivalent input noise, A-weighted:

1 uV (–120 dBV)

Phantom power (optional): 9 V DC / max. 100 mA,

short-circuit protected

channel 2

Switchable instrument or microphone input

Combo socket, XLR + jack ¼" (6.35 mm)

line mode

High impedance, unbalanced input for

instruments (pick-ups) and line-level sources

Jack socket only

Sensitivity: 27 mV (–31 dBV)

Impedance: 1 Meg

Equivalent input noise, A-weighted:

2.4 uV (–112 dBV)

mic mode

XLR (balanced), stereo jack (balanced), or mono

jack (unbalanced) input

Sensitivity: 3.3 mV (–50 dBV)

Impedance (balanced mode): 1.2 k

Impedance (unbalanced mode): 2.7 k

Voice filter: –10 dB at 270 Hz (referred to 10 kHz)

Equivalent input noise, A-weighted:

0.8 uV (–122 dBV)

Phantom power (XLR only): 48 V, max. 10 mA,

short-circuit protected

clip indicators

clip

Headroom: min. 8 dB

clip

for ch. 1 and 2

return

Input from external parallel effect loop, or

supplementary input, before master volume

Mono jack, ¼" (6.35 mm)

Sensitivity: 320 mV (–10 dBV)

Impedance: 20 k (note: impedance changes to 5 k

while external effect is switched OFF by

footswitch)

Outputs (note 3)

Outputs

phones

Headphones output. When plugged in, internal

speaker is muted.

Stereo jack socket, L/R connected, ¼" (6.35 mm)

Max. output power: 2 x 100 mW / 1000 ohm

Input sensitivity for 2 x 50 mW / 1000 ohm:

23 mV (–33 dBV) at channel 1 input

Impedance: 470 ohm (common for L and R)

Note:

Note: Suitable for headphones with stereo jack.

Note:

Does not work with mono jacks.

tuner

Tuner output

Mono jack socket ¼" (6.35 mm)

Output voltage: 340 mV (–9 dBV)

line out

Preamplifier output after tone controls, with

effects, and after master volume

Mono jack, ¼" (6.35 mm)

Output voltage: 1.4 V (+3 dBV)

DI DI DI DI- - - - out

out

Balanced XLR output before master, after tone

controls, without effects

1 = ground

2 = positive

3 = negative

Differential output voltage: 140 mV (–17 dBV)

send

Output to external parallel effect loop

Before master, after tone controls

Mono jack, ¼" (6.35 mm)

Output voltage: 1.4 V (+3 dBV)

Footswitch connector

footswitch

Stereo jack socket ¼" (6.35 mm) for a dual

footswitch

Tip = internal effect on/off

Ring = external effect on/off

Sleeve = common (ground)

Effect is OFF when the footswitch is ON.

Tone controls

ch. 1

colour

–3 dB at 700 Hz, +10 dB at 8 kHz

ch. 1

colour

±8 dB at 100 Hz (shelf type)

bass

±6 dB at 800 Hz

middle

±8 dB at 10 kHz (shelf type)

treble

ch. 2

±8 dB at 100 Hz (shelf type)

ch. 2

bass

±11 dB at 10 kHz (shelf type)

treble

Effects

Internal effects

1 Reverb 1

2 Reverb 2

3 Delay

4 Chorus

External effect

Parallel effect loop (see also send

eff. pan

eff.

pan

Blends both internal and external effects

eff.

pan

between channels 1 and 2, with reverse direction

of rotation for the external effects.

Power

Power amp

60 W / 4 ohm, DMOS, monolithic I.C.

Power amp

Dynamic range, A-weighted: 92 dB (note 2)

Limiter

50 W

threshold

Analog signal

Dedicated equalizer, subsonic filter, adaptive

Analog signal

processing

peak limiter

processing

Speaker system

8" (200 mm) twin cone full-range speaker, bass

Speaker system

reflex enclosure

Mains power

Mains voltage (depending on model):

100, 120, 230, or 240 V AC, 50–60 Hz

Power consumption: max. 120 W

Mains fuse

5 x 20 mm

T 1 A L / 250 V for 230 and 240 V models

T 2 A L / 250 V for 100 and 120 V models

General

Cabinet

12 mm (0.47") birch plywood

Finish

Waterbased acrylic, black spatter finish (standard

model)

Dimensions

259 mm (10.19") high

Dimensions

331 mm (13.03") wide

137 / 326 mm (5.39" / 12.84") deep

Weight

7.2 kg (15.87 lbs)

Weight

Notes:

1. Sensitivity

Input sensitivities refer to 50 W into 4 ohm, full gain and master settings,

neutral tone control settings, and 1 kHz sine-wave test signal.

2. Noise and dynamic range

Equivalent input noise voltages are typical values obtained by measuring

noise voltage at speaker output and dividing by the voltage gain of the

amplifier for white noise. Full gain and master settings, neutral tone

control settings, input shorted, measuring bandwidth 20 Hz – 20 kHz.

Dynamic range of power amplifier: Ratio of between output signal at

limiter threshold to A-weighted output noise with master

position.

3. Output levels

Output levels refer to 50 mV / 1 kHz sine-wave test signal at channel 1

input, full gain and master settings, neutral tone control settings, send

fully clockwise.

4. Options

Gain of channel 2 in mic mode can be decreased by 4.6 dB by an internal

jumper.

48 V phantom power can be deactivated by an internal jumper.

9 V phantom power for channel 1 can be applied by an internal jumper

to the "ring" terminal of the input jack. Caution:

care. Read the operating instructions.

Specifications and appearance subject to change without notice.

send and return

send

return).

return

master in zero

master

Caution: Use this option with

Caution:

TD20150224

Table of Contents

Show Quick Links

Hide quick links:

Table of Contents

Technical Specifications - AER Compact Slope User Manual

Hide quick links:

Related Manuals for AER Compact Slope

Related Content for AER Compact Slope

Table of Contents