RAILKING N&W J WITH LOCO-SOUND READY-TO-RUN TRAIN SET OPERATING INSTRUCTIONS ® Your RailKing Ready-To-Run train set is complete with everything you need to get your model railroad up and running. This set includes a N&W J 4-8-4 steam locomotive, a set of thre e passenger cars, a transformer, a loop of RealTrax, the RailKing wireless infrared remote control, and the infrared activated remote lock-on.
Remote Lock On can be installed Remove Knock Out by Holding and Twisting Up with a pair of pliers Make sure the metal contacts line up. Figure 1a-1d: Installation of Remote Lock On RailKing N&W J Steam Engine...
(see figure 4), then gently blow into the stack to eliminate any air bubbles in the fluid. Figure 4. add Smoke Fluid Through the Smoke Stack RailKing N&W J Steam Engine...
Figure 6. Coupling the Passenger SERIOUS DAMAGE. Look at the Cars Together bottom of the engine and tender where each will have a color-coded stamp. If they match you may connect those two pieces; if not, don’t. RailKing N&W J Steam Engine...
Proto-Sound or with ™ ™ ™ Proto-One, Proto-Plus, Proto-Deluxe, aftermarket systems. Whistle/ Bell Horn Throttle Control Rocker Switch Emergency Direction Stop Figure 7: Overview of the Remote controls RailKing N&W J Steam Engine...
To prevent accidental high-speed start-ups, this engine is programmed to restart in neutral each time the track voltage is turned off for 25 seconds or more. RailKing N&W J Steam Engine...
Bell button. The engine will not change direction (including going into neutral) until you repeat the 1 whistle, 3 bells code to return the engine to its normal state. RailKing N&W J Steam Engine...
If you experience popping and interference, try cleaning the track with denatured alcohol as described in the “Cleaning the Wheels, Tires and Track” section of this booklet. Note: M.T.H. does not recommend using Proto-Cast and Proto-Dispatch at the same time. RailKing N&W J Steam Engine...
“L” in Fig. 10. Do not over oil. Use only a drop or two on each pivot point. Lubricate Side Rods and Linkage (L) Lubricate Pick Up Rollers (L) Figure 10. Lubrication Points on the Locomotive RailKing N&W J Steam Engine...
Page 12
Follow the grease points shown on Fig. 11. Body Mounting Screws Body Mounting Screws Lubricate Pivot Point (G) Grease Screw (G) Figure 11. Greasing Points on the Engine and Body Mounting Screws RailKing N&W J Steam Engine...
5. Make sure the tire is fully seated inside the groove. Use a razor blade to trim away any excess tire that doesn’t seat itself inside the groove properly. Replacement tires are available directly from the M.T.H. Parts Department. RailKing N&W J Steam Engine...
(see Fig. 12 ). After removing the chassis and inspection cover screws, lift the inspection plate away and inspect the wick. If it is darkly discolored and Figure 12. Inspection Cover Screws hard, it should be replaced. RailKing N&W J Steam Engine...
Figure 13 to remove. You can obtain replacement bulbs directly from the M.T.H. Parts Department (phone: 410-381-2580; e-mail: parts@mth-railking.com; mail: 7020 Columbia Gateway Drive, Columbia MD 21046-1532). HeadLight Figure 13. Changing the Locomotive’s Headlight Bulb RailKing N&W J Steam Engine...
You can obtain replacement bulbs directly from the M.T.H. Parts Department. Roof Mounting Screw Roof Mounting Screw Interior Mounting Screw Interior Mounting Screw Roof Mounting Screws Figure 14. Instructions for Replacing the Lights in the Passenger cars. RailKing N&W J Steam Engine...
5. Choose the folder inside entitled RRTRAXSETUP. 6. Run the file in that folder called SETUP.EXE and follow the directions it provides. The program may ask you for a registration code. If it does type in MTH and it will run. RailKing N&W J Steam Engine...
Page 18
*If you are running Windows 95, 98 or NT choose the folder 32 BIT. Run the file AR32E301.EXE and follow the directions it provides. If you have problems you cannot resolve by using these directions, contact custserv@mth-railking.com for further help. RailKing N&W J Steam Engine...
“Lock into a Direction” section. with the engine sounds running. Engine speed must be below 10 scale The engine won’t lock into forward, mph (approx. 10 volts or less in neutral, or reverse. conventional mode). RailKing N&W J Steam Engine...
It is also compatible with most standard AC transformers, including the hobby transformer packaged with your set. (See page 21 for a complete list of compatible transformers and wiring instructions.) RailKing N&W J Steam Engine...
Lionel SW Unknown 130-Watt Standard Lionel TW 8-18v 175-Watt Standard Lionel ZW A,B,C or D 8-20v 275-Watt Standard Lionel Post-War Common 0-20v 135/190 Watt Electronic A,B,C or D Celebration Series ZW * Conventional Mode Only RailKing N&W J Steam Engine...
• Unplug the transformer from the electrical wall outlet when not in use. • Do not use this transformer for other than its intended purpose. Transformer Ratings: Input: 120 VAC 60 Hz Only Output: 21VAC, 3.75A 78VA (for sets with Z-750) RailKing N&W J Steam Engine...
Service & Warranty Information How to Get Service Under the Terms of the Limited One-Year Warranty For warranty repair, do not return your product to the place of purchase. Instead, follow the instructions below to obtain warranty service as our dealer network is not prepared to service the product under the terms of this warranty.
Need help?
Do you have a question about the RAILKING N and is the answer not in the manual?
Questions and answers