Subscribe to Our Youtube Channel
Related Manuals for Microseven Systems MSHCX080
Summary of Contents for Microseven Systems MSHCX080
- Page 1 Product Operation Manual MSHCX080 Network IP Camera Microseven Systems, Inc. Walnut, California 91789, USA...
- Page 2 Copyright © 2002-2008 Microseven Systems, Inc. All Rights Reserved. Microseven Systems, Inc. provides this operation manual “as is” without warranty of any kind, either express or implied, including, but not limited to the implied warranties of merchantability and fitness for a particular purchase. Microseven Systems, Inc. may make improvements and/or changes in the product(s) and/or the program(s) described in this manual at any time and without notice.
- Page 3 Model: Product №: © 2002-2008 Microseven Systems, Inc. All Rights Reserved.
-
Page 4: Table Of Contents
4. Instructions of Main Parts ………………………………………………………………. 8 5. Alarm and Audio Connector ……………………………………………………………………… 6. Setup and Adjustment ……………………………………………………………………… 7. Installation of Camera ………………………………… 8. Basic System Diagram and Operating Circumstance …………………………………………………………………………..…… 9. Specification © 2002-2008 Microseven Systems, Inc. All Rights Reserved. -
Page 5: Preface
® 1. Preface MSHCX020/MSHCX080 series Network IP cameras adopts SONY CCD, with bright and exquisite images. As video & audio multi-media equipment that based on network transmission, which adopts built-in and multi-media communication technology, the camera is a multi-media network terminal that can directly connect to the network. -
Page 6: Notes
Use the camera under conditions where temperature is between -10°C - + 50°C and humidity is below 90% H. The power supply for MSHCX080 is DC12V. The adapter with electric current of over 2A is recommended. The pictures in the manual are for reference. -
Page 7: Instructions Of Main Parts
1 channel analog video output, 1 channel RS485 output. ⑨ Alarm and Audio Connector Alarm: None-source alarm input and output. Audio Input: 1 channel / microphone input. ⑩ Network Interface RJ-45 standard interface © 2002-2008 Microseven Systems, Inc. All Rights Reserved. -
Page 8: Alarm And Audio Connector
5.2 Alarm Instruction When there is alarm signal, the switch S closes and alarm output terminal takes action, and indicator is ON; on contrary, the indicator is OFF when there isn't alarm signal. © 2002-2008 Microseven Systems, Inc. All Rights Reserved. -
Page 9: Setup And Adjustment
The pin assignment of the lens connector is as follows: DC Drive Pin 1 DAMP- Pin 2 DAMP+ Pin 3 DRIVE+ Pin 4 DRIVE- B. After connection, assemble the lens connector as follows: © 2002-2008 Microseven Systems, Inc. All Rights Reserved. - Page 10 Turn the back focal adjusting ring to the desired position. 6.5 Adjusting of focus or back focus Following adjusting work should be done by qualified maintainer or system installer. loosen the screws on the back focal adjusting ring © 2002-2008 Microseven Systems, Inc. All Rights Reserved.
-
Page 11: Installation Of Camera
Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the diagram, and then mount the camera on the mounting bracket. © 2002-2008 Microseven Systems, Inc. All Rights Reserved. -
Page 12: Basic System Diagram And Operating Circumstance
8. Basic System Diagram and Operating Circumstance Operate environment After the equipment installed and connected to the network, it should be operated on Server Software Platform of Microseven Digital Video Server. © 2002-2008 Microseven Systems, Inc. All Rights Reserved. -
Page 13: Specification
Timing detection of chips & software work status, auto system reset Built-in Watchdog Realize remote reset through network Remote Reposition Compressed Code Rate/ 32Kbps / IEEE 802.11b/g standard Wireless function ~ +50 Working Temperature ≤95% Working Humidity DC12V, 2A Power Source © 2002-2008 Microseven Systems, Inc. All Rights Reserved.
Need help?
Do you have a question about the MSHCX080 and is the answer not in the manual?
Questions and answers