Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TALAMEX TLM200A
Summary of Contents for TALAMEX TLM200A
- Page 1 TALAMEX INFLATABLE BOATS OWNER’S MANUAL LANKHORST TASELAAR B.V.
-
Page 2: Table Of Contents
Contents page GENERAL INFORMATION HIN-HULL IDENTIFICATION NUMBER ASSEMBLY AND DISASSEMBLY USING THE BOAT REPAIR PROCEDURE WARRANTY DECLARATION OF CONFORMITY... -
Page 3: General Information
GENERAL INFORMATION Congratulations on the purchase of inflatable boat. Please read this manual carefully before inflating, assembling or using your boat. Also study carefully the manual supplied with your outboard engine. Familiarise yourself with the features of the boat and the engine and ask for professional training if you are inexperienced in handling this type of boat. -
Page 4: Specifications
Max.Load Max.power Weight Design Model. Length Beam dia. Model Cust.Code Pers. Cat. Code lbs/kg kw/hp TLM200A 654 / 297 2.98 / 4 26.78 682 / TLM230L 3.97/5 28.4 309.20 819 / TLM240A 3.97 / 5 34.5 371.47 704 / TLM240X 3.97/ 5... -
Page 5: Hin-Hull Identification Number
HIN-HULL IDENTIFICATION NUMBER The HIN is visible at the starboard side of the transom. Do not alter, cover or remove the HIN. It may void the warranty and can get you into legal problems. Record the HIN of your boat in the designated place on the Declaration of Conformity’ in this manual. Also write it down in a safe place. -
Page 6: Assembly And Disassembly
· Passengers: unnecessary people off the boat. · All electrical equipment: off. · Fill less than rated capacity of tank, allow for fuel expansion. · Follow engine manufacturer’s recommendations for types of fuel and oil. · Refer to outboard motor manual for details. ASSEMBLY AND DISASSEMBLY Attention ! Do not use a compressed air source (such as a compressor) to inflate boats. - Page 7 B-Keel valve A-Tube valve Location of Valve 4. When using the boat for the first time, fully inflate it by attaching the foot pump to each of the valves, one at a time, and when pumping, ensure that a balance of pressure between the chambers is maintained until the boat has been fully inflated.
- Page 8 1. Unfold and stretch out the floor onto the bottom of the boat, edging it under the half-inflated tubes and against the transom. The valve must face upwards. 2. Inflate the floor up to ¾. 3. Finish inflating the boat. 4.
- Page 9 2. Slide an oar (a) under the bottom of the boat to raise the floor boards (b) over the flat surface. Attach side joiners (c). Repeat the procedure on opposite side of the boat. In case of more than one joiner on each side, start with one long, one short joiner on one side and with one short and one long on the other side (asymmetric).
-
Page 10: Using The Boat
CLEANING PROCEDURES Rinse your boat when possible, after each use. At the end of a season, wash it out in soapy water or with washing-up liquid. Rinse, let dry then apply talcum powder before folding up the boat. Store in a dry place. IMPORTANT : DO NOT use a vinyl preserving agent on fabric surfaces. - Page 11 in the water or allow a swimmer to approach the stern of the boat while the engine is running. 7. Due attention should be given to winds and tides, which can change and therefore affect fuel consumption. 8. When boating in unknown waters, it is always a wise precaution to obtain local knowledge before setting out.
- Page 12 4. When inflating, maintain a balance of air between air chambers to prevent damage to air chamber bulkheads. LOADING 1. DO NOT EXCEED THE WEIGHT CARRYING CAPACITY INDICATED ON THE BOAT IDENTIFICATION PLATE. 2. Each person in the boat should wear a life jacket (personal flotation device). 3.
- Page 13 1. The inflatable MUST BE EMPTY when it is towed by another boat. The towing line should be secured to the "D"-rings on each side of the inflatable. The inflatable must be under constant supervision when it is being towed. 2.
-
Page 14: Repair Procedure
IMPORTANT : Waxes or cleaners containing alcohol SHOULD NOT be used on the boat fabric. Alcohol will prematurely dry out the boat fabric. 4. To avoid damaging the boat during storage, do not place heavy objects on USE IN HIGHER ALTITUDES 1. - Page 15 workmanship, but only when the sale has been made in a country to which distribution is authorised by us. II. This warranty applies only to defects in material and workmanship, it does not apply to normal wear and tear, or to damage caused by: 1) Neglect, lack of maintenance, accident, abnormal or improper use or bad assembly;...
-
Page 16: Declaration Of Conformity
- EC Approvals for boats larger than 2.50 m according to EC Directive 94/25/EC Recreational Craft Description: Inflatable Boat Brand : TALAMEX Boat type : TLM200A TLM230L TLM240A TLM240X TLM260A TLM260X TLM280A TLM280X TLM300X TLM350P TLM380P Certification Module : A a(All Models) Design category - Inflatable : ISO ref. - Page 17 On behalf of the producer: - Name : Mr. Cho Ki Sung - Date : 27 April, 2007 - Function : Producing Director - Signature : Enter here your HIN Please sign hereunder for receipt of this manual and all the relevant manuals Of equipment onboard.