Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TALAMEX QLS200
Summary of Contents for TALAMEX QLS200
- Page 1 Talamex inflatable boats – User’s manual TLM-GB2021-01 Pagina 1 van 17...
-
Page 2: Table Of Contents
Talamex inflatable boats – User’s manual Contents General ................................3 Introduction ..............................3 Design categories ............................3 Capacity plate.............................. 4 National legislation ............................. 4 General safety information .......................... 4 Specifications, description and features ....................... 4 Specifications .............................. 4 Boat model ..............................4 Number of persons ............................ -
Page 3: General
Ensure that the anticipated wind and sea conditions serious injury. will correspond to the design category of the Talamex inflatable boat and that you and your crew are able to handle the Talamex inflatable boat in caution these conditions. -
Page 4: Capacity Plate
Before you prepare for the water with your Talamex The operator should always have the down skier in inflatable boat, check the local legislation on any sight and never back up to the skier or anyone in the restrictions on the specific water you want to use. -
Page 5: Number Of Persons
Ask your dealer for supply of a fire extinguisher that is conform the requirements. Payload warning Electrical system When loading the Talamex inflatable boat, never let op exceed the maximum recommended load. Always load the Talamex inflatable boat carefully and distribute loads appropriately to maintain design Your Talamex boat comes standard without trim (approximate level). -
Page 6: Specifications
Talamex inflatable boats – User’s manual Specifications Model QLS200 Kort 93 x 47 x 20 QLS230 Kort 98 x 45 x 25 QLS250 6185- 1 Kort 98 x 50 x 25 QLA230 Kort 3+1+1 98 x 45 x 25 QLA250... -
Page 7: Drawings
Talamex inflatable boats – User’s manual 2.10 Drawings Pagina 7 van 17... -
Page 8: Assembly And Disassembly
Step 2: Put in enough pressure to allow the boat to Rowing equipment spread out, but do not fully inflate the tube. Talamex boats come standard or with paddles or with Step 3: Repeat procedure, pump the remaining oars, oarlocks, and a seatbench. The oars can be chambers to right pressure. -
Page 9: Floorboard
The pump that is delivered gives exactly the right pressure to your boat. Floorboard Talamex boats that are equipped with an inflatable or a non-inflatable floorboard must be operated with these floorboards properly installed before use. Using the boat without provided floorboard is unsafe, uncomfortable and it might result in damage to the boat. -
Page 10: Installing Airfloor
The slatted floor of your Talamex boat has already In the back of the boat there are two transom tracks been installed. You only need to inflate the tubes in fixed against the transom. -
Page 11: Engine Installation
All Talamex boats are designed for using a short shaft motor The Deflating the boat: motor position is essential for the right sailing •... -
Page 12: Folding The Boat
(4). boat for towing (towing D-rings). Towing this way makes the boat steady and secure behind the towing boat, and helps to avoid damage to your Talamex boat. See drawing 2.10 for location of these components. Attach a line between the towing D-rings to form a bridal/triangle. -
Page 13: Operation- And Safety Instructions
• Check that the lanyard stop switch for the especially when operating an outboard engine. outboard works correctly. It is possible as well, to get the Talamex into “aqua- • Be sure the boat is not overloaded. Do not planing”. -
Page 14: Hazards
Your Talamex boat is designed with more than one air chamber. Therefore, although in the event one of the air chamber might leak due to a puncture, the Avoid heavy weights near the transom. -
Page 15: Reboarding
If you have any damage to your Talamex inflatable possibility of the tank overflowing or even breaking. boat, it is strongly advised to go to your Talamex High altitude use Boat dealer for repairs. -
Page 16: Winter) Storage
• Wait 24 hours before you inflate the boat again. Consult your local dealer when experiencing problems. A repair kit is standard delivered with your Talamex inflatable boat. (Winter) storage IMPORTANT: To prevent hull or tube discoloration from marine growth or polluted waters, DO NOT store boat in the water for extended periods of time. -
Page 17: Warranty
N. Costs of normal maintenance and cleaning; rot, is valid. The material of all the other Talamex boats are O. Consequential damage or incidental damage; covered by a 2-year warranty against cracking, porosity P.