Front Panel; Front Panel Display - Cambridge Audio azur 752BD User Manual

Front panel

Standby / On
1 2 3
1. Standby/On
Switches the unit between Standby mode (indicated by a dim power LED)
and On (indicated by a bright power LED). Standby is a low power mode
where the power consumption is less than <0.5W. The unit should be left
in Standby mode when not in use.
2. IR sensor
Receives IR commands from the supplied Azur Navigator remote control.
A clear unobstructed line of sight between the remote control and the
sensor is required.
3. USB port
Port for interfacing to a flash/memory card or "Mass Storage Devices"
(such as a portable hard-drive).
Notes:
• Only USB 2.0 certified products with the USB 2.0 logo on them are
supported by the 752BD. Please either consult the manufacturer of
the USB 2.0 product to make sure it is properly certified, or go to www.
usb.org for a list of approved products. We cannot be held responsible
for any incompatibility issues.
• This unit supports "USB Mass Storage Class Bulk-Only Transport"
devices only. Most USB thumb drives, portable hard disk drives and
card readers conform to this device class. Other USB devices such
as MP3 players, digital cameras, and mobile phones may not be
compatible.
• See USB port section for file system compatibility.
4. Filter select
Press to select between three different digital filter modes: linear phase,
minimum phase or steep. The corresponding LED will light up to show
which filter has been selected. There affect the analog outputs only.
See later section for details.

Front panel display

1 2 3 2 4
11 12
1. Disc Type Indication – Indicates the currently playing disc type.
2. Track/Chapter – When illuminated, the displayed time applies to
a track or chapter.
3. Title/Group – When illuminated, the displayed time applies to a
title or group.
4. Total – When illuminated, the displayed time is the total play time.
5. Remaining – When illuminated, the displayed time is the remaining
play time.
4
5 6 7 8 9 10
13 14
6
5
7
5. Display
Used to display the 752BD's functions and playback state, etc. Please
refer to the front panel display section below for more information.
6. Disc tray
Use the Open/Close button to activate.
7. Open/Close
Allows opening and closing of the disc tray for loading of discs. Pressing
Play will also close the tray and start playing a disc if one is loaded.
8. Play/Pause
Plays the disc and pauses (freezes) playback.
9. Stop
Press once to stop playback. Pressing Play will cause the playback to
be re-started from the same position. Press Stop again to fully stop
playback.
10. Skip
Press once to skip between tracks/chapters.
11. MHL (Mobile High-definition Link)/HDMI Input
This input is used to connect to a mobile source device such as a mobile
phone or a digital camcorder.
The combined socket allows either a standard HDMI source to be
connected to the 752BD or alternatively an MHL device (such as some
new phones) in which case the device can also be charged whilst sending
digital audio/video to the 752BD.
Note: To utilise the MHL capability, the source device needs to be MHL
enabled and a MHL cable/adaptor is required.
6. Playback Status – Indicates playback status such as Play, Pause,
Repeat, Repeat All, Random/Shuffle, and A-B Repeat.
7. Angle Icon – Indicates that the scene contains additional camera
angle(s) that can be selected.
8. HDMI – Indicates that the HDMI output is active.
9. Network – Indicates that the unit is connected to a network.
10. Wireless – Indicates a connection to a wireless network.
11. Mute Icon – Indicates that the audio is muted.
12. Audio Channel Indication – Indicates whether the audio is 2ch
stereo or multi-channel surround.
13. Main Display – Text messages and numeric display.
14. Audio Type Indication – Indicates the type of audio tracks playing.
azur 752BD
azur
752BD
Blu-ray Disc Player
MHL/HDMI In
8 9 10 11
9