NH1C1M HT1M • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” TV-F2100 (NH), (S/M Code No. 09-007-432-1T2). • This Service Manual does not include “ADJUSTMENT”. This item will be issued in the next Supplement. S/M Code No. 09-008-432-1R2...
SPECIFICATIONS Tuner System Frequency synthesized tuner TV System NTSC-M Channel Coverage VHF: 2 to 13 UHF: 14 to 69 CATV: 5A, A-1 to A-5, A to W, W+1 to W+84 Program Memory Antenna Input 75 ohms, unbalanced Picture Tube 21 in Screen Size 406 (W) x 305 (H) mm (16 x 12...
NOTICES BEFORE REPAIRING To make the best use of this equipment, make sure to obey the following items when repairing (or mending). 1. Do not damage or melt the tunicate of the leading Insulation resistance: 3.8 to 5.6 MΩ (500 V/s) wire on the AC1 side, including the power supply Voltage-withstand: 1 kV for 1 minute cord.
DISASSEMBLY INSTRUCTIONS 1. REAR CABINET REMOVAL Front cabinet (1) Remove four screws 1, and three screws 2, then remove the rear cabinet in the direction of the arrow. (See Figure1-1) Rear cabinet Figure 1-1 2. HIGH-VOLTAGE CAP (ANODE CAP) REMOVAL 2-1.
Page 5
(5) Push the anode cap with your thumb in the direction of arrow 1 as shown in the figure, then lift the cap in the direction of arrow 2 to release the hook on one side. (See Figure 2-3) Anode cap Hook Hook Figure 2-3...
Page 6
(3) Eliminate twisting, etc. of the high-voltage cable and High-voltage cable Anode cap arrange it so that no twisting occurs. (See Figure 3-3) Caution : If the cable is not arranged correctly, the anode cap could turn and cause an installation defect. Figure 3-3 (4) Turn over the rubber cap symmetrically on the left and right.
Page 7
(6) Apply the hook on one side to the anode button as shown on the figure. (See Figure 3-6) Caution : Check that the hook is held securely. (7) Apply the hook on the other side to the anode button as Hook shown in Figure 3-7.
Page 8
4. NK C.B REMOVAL Front cabinet (1) Disconnect CN903 (CRT GND). (2) Disconnect CN901, CN902, CN951, CN952. CN882 (3) Remove the NK C.B. in the direction of arrow 1. (Power Cord) (See Figure 4-1) CN807 (Degauss 5. MAIN C.B REMOVAL cord) (1) Remove connector (CN404).
Page 9
ELETRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 87-A40-553-080 DIODE,1N4003 LES 87-A40-503-080 ZENER,MTZJ39B 8A-JE7-625-010 IC,M37272M8-503SP<HT> 87-A40-785-080 DIODE,SB040 8A-JE7-623-010 IC,M37272MA-055SP<NH1M,NH1C1M> 87-A40-856-080 DIODE,UF4007 87-A91-538-010 RCR UNIT,SBX1981-72P 87-A40-850-090 DIODE,RL4A 87-A21-378-010 IC,S-24C04BDP-1A 87-A20-611-080 IC,M51943BSL-700A<NH1M> MAIN C.B 87-001-536-010 IC,NJM78M05FA 8Z-JBJ-605-010...
Page 10
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C321 87-010-404-080 CAP, ELECT 4.7-50V C736 87-010-401-080 CAP, ELECT 1-50V C322 87-A10-295-080 CAP,M 0.01-50 J C737 87-018-134-080 CAPACITOR,TC-U 0.01-16 C323 87-016-280-080 CAP,E 3.3-50 M BP SME C801 87-010-408-080 CAP,E 47-50 M 11L C324 87-018-134-080...
CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor Chip resistor Dimensions (mm) Wattage Type Tolerance Symbol Resistor Code Form 1/16W 1005 0.35 1/16W 1608 0.45 1/10W 2125 1.25 0.45 1/8W 3216 0.55 TRANSISTOR ILLUSTRATION E C B B C E B C E...
Page 26
IC DESCRIPTION IC, M37272MA-055SP<NH1M,NH1C1M>, IC, M37272M8-503SP<HT1M> Pin No. Pin Name Description BLK H Blanking H sync input. BLK V Blanking V sync input. A MUTE Audio Amp mute. L MUTE Audio mute. Q SUR Q surround switch. EEPROM Write protect. V MUTE Video mute BPF switch.
Need help?
Do you have a question about the TV-F2100 and is the answer not in the manual?
Questions and answers