Related Manuals for U.S.SAWS ACH GB-16
Summary of Contents for U.S.SAWS ACH GB-16
-
Page 1: Chain Saw
Air Powered Chain Saw Model: ACH GB-16 Operating Manual Toll Free 1-877-987-7297 3317 West Warner Avenue 11 High Street 8004B East Broadway Avenue Santa Ana, CA 92704 Suffield, CT 06078 Tampa, FL 33619 www.ussaws.com... -
Page 2: Table Of Contents
Introduction This manual outlines the maintenance and operation of the ACH GB series, air powered chain saw. This is a professional tool and is intended for use by trained and experienced operators. To get maximum benefit from your saw and to ensure maximum safety, be sure to read this manual thoroughly. -
Page 3: Symbols & Labels
Symbols & Labels THE FOLLOWING SYMBOLS AND DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR SYMBOLS & LABELS TITLE 633GC / 633F4 OPERATOR’S MANUAL UNSAFE PRACTICES. THE FOLLOWING SYMBOLS & DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. -
Page 4: Safety
THE FOLLOWING SYMBOL APPLIES TO ALL THE ITEMS LISTED ON THIS PAGE Safety A potentially hazardous situation exists which, if not avoided WARNING could result in death or serious injury. SYMBOLS & LABELS TITLE 633GC / 633F4 OPERATOR’S MANUAL THE FOLLOWING SYMBOLS & DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND This symbol applies to all information listed on this page ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. -
Page 5: General Safety Precautions
SYMBOLS & LABELS TITLE 633GC / 633F4 OPERATOR’S MANUAL THE FOLLOWING SYMBOLS & DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND Safety ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. A potentially hazardous situation exists which, if not avoided, WARNING could result in death or serious injury. -
Page 6: Set-Up
SYMBOLS & LABELS TITLE 633GC / 633F4 OPERATOR’S MANUAL THE FOLLOWING SYMBOLS & DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND SYMBOLS & LABELS TITLE 633GC / 633F4 OPERATOR’S MANUAL ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. THE FOLLOWING SYMBOLS &... - Page 7 695GC / 695F4 OPERATOR’S MANUAL Set-up STALLATION Guide Bar and Diamond Chain Installation CORRECT CHAIN TENSION All chains have a tendency to stretch when used. Diamond chains stretch more than wood cutting chains because of the CORRECT CHAIN TENSION abrasive materials they are cutting. All chains have a tendency to stretch when If the chain is too tight, a lot of the saw's used.
-
Page 8: Chain Tension
Air Saws • Gas Saws • Pipe Saws • Concrete Saws • Hydraulic Saws aws • Gas Saws • Pipe Saws • Concrete Saws • Hydraulic Saws Chain Tension aws • Gas Saws • Pipe Saws • Concrete Saws • Hydraulic Saws aws •... - Page 9 Chain Tension AddITIONAl INfORmATION ood cutting chainsaws use oil to lubricate Air Saws • Gas Saws • Pipe Saws • Concrete Saws • Hydraulic Saws s the chain very slippery and allows the between the teeth of the drive sprocket. aws require water for cooling and flushing good as oil as a lubricant.
-
Page 10: Pipe Clamp
Pipe Clamp Pipe Clamp Mounting Instructions 1. Assess pipe and area to cut. Ensure the chain saw will pass freely around any objects in and around the path of the cut. (ie: power lines, telecommunication lines, rocks, tools, etc.) 2. Ideally the pipe clamp should be mounted in a position that allows the locking pliers to be on the top side of the pipe. -
Page 11: Chain Tensioning
Pipe Clamp Reciever Pin Mounting Instructions • Remove the rear bar stud nut. • Install pin on rear bar stud. • The inner thread of the pin will take the place of the nut. • In certain applications (larger than 10” pipe) the mounting pin may need to be relocated to the front bar stud for greater saw clearance. -
Page 12: Operation
695GC / 695F4 OPERATOR’S MANUAL TITLE OPERATION 695GC / 695F4 OPERATOR’S MANUAL TITLE OPERATION STARTING AND STOPPING A CONCRETE CHAIN SAW Operation STARTING AND STOPPING A CONCRETE CHAIN SAW Never start a concrete chain saw without the bar, chain and side WARNING cover properly assembled. - Page 13 Operation Before cutting, make sure the pipe is in a safe condition to be cut. Support the piece you are going to be cutting in such a way that the cut will remain open during the cut and when the cut is finished. Pinching the chain during the cut could cause chain breakage and 695GC / 695F4 OPERATOR’S MANUAL TITLE...
-
Page 14: Troubleshooting
Troubleshooting • SLOW CHAIN SPEED - Be sure the compressor is providing the correct air pressure, 90 psi, and cubic feet per minute, 90 cfm. These are the minnimum requirements; ideal performance can be achieved at higher volume. • POOR CUTTING PERFORMANCE - Diamonds may be “glazed over”. Make a few cuts in abrasive material such as cinder block to expose diamonds. -
Page 15: Maintenance
Maintenance Air Motor Maintenance Only proper maintenance can ensure consistent saw performance, reduction of wear, and thus, a reduction in operation costs and an increase in service life. Service life and performance of the chain saw are determined by: 1. Degree of air purity 2. -
Page 16: Parts 16
Parts Ref. Number Part Number Description Note US60510C Hand Guard US60466-3 Handle US60466-5 Handle Spacer US60134 Trigger Guard US60466-1 Chain Chassis US60466-2 Chain Cover US60523 Flap Not Shown US60466-8 Adjustment Pin US60466-12 Pin Washer US60466-11 E - Clip US60466-7 Adjust Bolt US60530 Stud Bolt 2 Required... - Page 17 Parts Ref. Number Part Number Description Note 02-70018 Governor End Bolt 02-70017 Bearing Sleeve 02-70070 Bearing 02-65013 Gasket 02-54069 Large Bearing End Plate 02-40044A Roll Pin - Short 02-70011L Cylinder - Left Rotation 02-70037 Roll Pin - Long 02-70013 Vane 4 Required 02-70012 Rotor...
- Page 18 Parts 02-60051 Spring - Spindle Lock 02-66177 Spindle Lock Housing 02-40044A Roll Pin - Short 02-59202 Lock Clip 02-66201 Gearbox Housing 02-70046 1/4 Lock Washer 2 Required 02-70046A Hi-Cap Lockwasher 1/4 02-66113 Key - Small Gear 02-70047 Gear Box Housing Cap Screw 3 Required 02-66150 Low Speed Input Gear...