Chicago Electric 61441 Owner's Manual & Safety Instructions

Chicago Electric 61441 Owner's Manual & Safety Instructions

15 amp professional breaker hammer

Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 61441 and is the answer not in the manual?

Questions and answers

Summary of Contents for Chicago Electric 61441

  • Page 2: Table Of Contents

    2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Page 2 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 3: Electrical Safety

    Power tools are dangerous in the hands of untrained users. Item 61441 For technical questions, please call 1-888-866-5797. Page 3...
  • Page 4 14. This product is not a toy. Keep it out of reach of children. Page 4 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 5: Vibration Safety

    If you feel any symptoms related to vibration (such vibration occurs, stop use immediately. as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SAVE THESE INSTRUcTIONS. Item 61441 For technical questions, please call 1-888-866-5797. Page 5...
  • Page 6 Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Outlets for 2-Prong Plug Page 6 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 7: Extension Cords

    Risk of Electric Shock. Properly connect power cord to appropriate outlet. Amperes WARNING marking concerning Risk of Hearing Loss. n 0 xxxx/min. No Load Revolutions per Minute (RPM) Wear hearing protection. Item 61441 For technical questions, please call 1-888-866-5797. Page 7...
  • Page 8: Specifications

    Right Handle (51) while slowly manipulating Left Handle over the Spline Axle until the splines line up and it fits snug into place. See Figure B. Spline Axle (91) Nut (40) Figure c Page 8 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 9 Functions chisel Socket Lock Lever Main Handle Secondary Handle Trigger Item 61441 For technical questions, please call 1-888-866-5797. Page 9...
  • Page 10: Operation

    4. Pull the Lock Lever back until it touches the Spring, Lever locking the Chisel into place. See Figure F. Figure D Note: Flat Notch on Collar-less Chisel must face the Lock Lever. Figure F Page 10 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 11: Work Piece And Work Area Set Up

    6. Keep power cord away from moving machines. 3. Secure loose work pieces using a vise or clamps (not included) to prevent movement while working. Item 61441 For technical questions, please call 1-888-866-5797. Page 11...
  • Page 12: General Operating Instructions

    6. Press down on the Trigger. 10. Clean, then store the tool indoors Note: Trigger does not lock. Keep pressure out of children’s reach. on the Trigger to keep running the tool. Page 12 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 13: Maintenance

    NOTE: The Breaker Hammer has airtight construction, allowing long periods of use (approximately six • any other condition that may months of regular usage) before lubrication. affect its safe operation. Item 61441 For technical questions, please call 1-888-866-5797. Page 13...
  • Page 14 4. Use a Wrench to loosen the Nut (40) holding the Left Handle (82) in place. See Figure J. Left Handle (82) Wire Board (13) Nut (40) Bolt (12) Figure M Figure J Page 14 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 15 Then replace Left Handle and fasten that into place against Gearbox. Replace Cover 9. Snap spring back into place and use and fasten it into place using the Screws. Screw to replace Wire Board. Item 61441 For technical questions, please call 1-888-866-5797. Page 15...
  • Page 16 Piston’s OD, replace the O-ring. the Cylinder Case to the Crank Shaft Case and tighten them securely. cylinder case (58) Socket Head Bolt (57) Ram (60) Piston (61) crank Shaft case (8) Figure P Page 16 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 17: Troubleshooting

    Note: If product has no serial number, Note: Some parts are listed and shown for illustration record month and year of purchase instead. purposes only, and are not available individually as replacement parts. Item 61441 For technical questions, please call 1-888-866-5797. Page 17...
  • Page 18: Parts List And Diagram

    Parts with one or two asterisks are not available individually. You must purchase the parts kits. #98* - Bearing Kit includes part numbers 65*, 90*, 4*, 27* #99** - Seal Kit includes part numbers 62**, 59**, 87**, 69**, 35**, 72**, 78**, 31**, 26**, 25** Page 18 For technical questions, please call 1-888-866-5797. Item 61441...
  • Page 19 Assembly Diagram Item 61441 For technical questions, please call 1-888-866-5797. Page 19...
  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents