Download Print this page

Sony TA-S9D Service Manual

A/v amplifier
Hide thumbs

Advertisement

Quick Links

SERVICE MANUAL

Ver 1.0 2001.09
TA-S9D is the Amplifier section
in MHC-S9D.
Amplifier section
European model:
Front Speaker:
DIN power output (rated) 95 + 95 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
120 + 120 watts
(6 ohms at 1 kHz, 10%
THD)
Music power output (reference)
200 + 200 watts
(6 ohms at 1 kHz, 10%
THD)
Center Speaker:
DIN power output (rated) 30 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
40 watts
(8 ohms at 1 kHz, 10%
THD)
Music power output (reference)
75 watts
(8 ohms at 1 kHz, 10%
THD)
Rear Speaker:
DIN power output (rated) 30 + 30 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
40 + 40 watts
(8 ohms at 1 kHz, 10%
THD)
Music power output (reference)
75 + 75 watts
(8 ohms at 1 kHz, 10%
THD)
Other models:
The following measured at AC 120, 220, 240 V,
50/60 Hz
Front Speaker:
DIN power output (rated) 95 + 95 watts
(6 ohms at 1 kHz, DIN)
Sony Corporation
9-873-282-01
2001I0500-1
Home Audio Company
C 2001.9
Shinagawa Tec Service Manual Production Group
SPECIFICATIONS
Continuous RMS power output (reference)
120 + 120 watts
(6 ohms at 1 kHz, 10%
THD)
Center Speaker:
DIN power output (rated) 30 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
40 watts
(8 ohms at 1 kHz, 10%
THD)
Rear Speaker:
DIN power output (rated) 30 + 30 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
40 + 40 watts
(8 ohms at 1 kHz, 10%
THD)
Inputs
VIDEO (AUDIO) IN:
voltage 250 mV,
(phono jacks)
impedance 47 kilohms
MD IN:
voltage 450 mV,
(phono jacks)
impedance 47 kilohms
OPTICAL IN:
(Square optical connector jacks, rear panel)
MIC:
sensitivity 1 mV,
(Except for North
impedance 10 kilohms
American and
European models)
(phone jack)
Outputs
MD OUT:
voltage 250 mV
(phono jacks)
impedance 1 kilohms
VIDEO OUT:
max. output level
(phono jack)
1 Vp-p, unbalanced, Sync
negative, load impedance
75 ohms
S-VIDEO OUT:
Y: 1 Vp-p, unbalanced,
(4-pin/mini-DIN jack)
Sync negative,
C: 0.286Vp-p,
load impedance 75 ohms
TA-S9D
AEP Model
UK Model
E Model
Australian Model
PHONES:
accepts headphones of
(stereo mini jack)
8 ohms or more
FRONT SPEAKER:
accepts impedance of 6 to
16 ohms
REAR SPEAKER:
accepts impedance of 8 to
16 ohms
CENTER SPEAKER:
accepts impedance of 8 to
16 ohms
SUB WOOFER OUT:
Voltage 1 V,
impedance 1 kilohms
General
Power requirements
European model:
230 V AC, 50/60 Hz
Australian model:
230 – 240 V AC,
50/60 Hz
Mexican model:
120 V AC, 60 Hz
Korean model:
220 V AC, 60 Hz
Thailand model:
220 V AC, 50/60 Hz
Other models:
120 V, 220 V or
230 – 240 V AC,
50/60 Hz
Adjustable with voltage
selector
Power consumption
European model:
300 watts
0.6 watts (at the Power
Saving Mode)
Other models:
300 watts
Dimensions (w/h/d)
Approx. 280 x 128 x 350 mm
Mass
Approx. 7.7 kg
Design and specifications are subject to change
without notice.
A/V AMPLIFIER

Advertisement

loading

  Also See for Sony TA-S9D

  Related Manuals for Sony TA-S9D

  Summary of Contents for Sony TA-S9D

  • Page 1: Service Manual

    TA-S9D SERVICE MANUAL AEP Model UK Model Ver 1.0 2001.09 E Model Australian Model TA-S9D is the Amplifier section in MHC-S9D. SPECIFICATIONS Amplifier section Continuous RMS power output (reference) PHONES: accepts headphones of 120 + 120 watts (stereo mini jack)
  • Page 2: Table Of Contents

    LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
  • Page 3: Servicing Notes

    TA-S9D SECTION 1 SERVICING NOTES This set is a component of the MHC-S9D. MODEL IDENTIFICATION The MHC-S9D system configuration is as shown below, and there- fore it does not operate normally unless all four components are – Back Panel –...
  • Page 4: General

    TA-S9D SECTION 2 This section is extracted from instruction manual. GENERAL Parts Identification The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for details. A/V amplifier 1 2 3 ANGLE es (37) AUDIO ws (34)
  • Page 5: Disassembly

    TA-S9D SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.
  • Page 6: Case

    TA-S9D Note: Follow the disassembly procedure in the numerical order given. 3-2. CASE 1 three screws 4 Remove the case (BVTT3 × 6) in the direction of arrow A . 2 two screws (case 3 TP2) 2 two screws (case 3 TP2) 3-3.
  • Page 7: Back Panel (Dvd) Section

    TA-S9D 3-4. BACK PANEL (DVD) SECTION 8 back panel (DVD) section 5 three screws (BVTP3 × 8) 5 four screws 7 three connectors (BVTP3 × 8) (CN901, 902, 903) 1 screw (BVTP3 × 8) 5 four screws (BVTP3 × 8)
  • Page 8: Test Mode

    SECTION 4 TEST MODE Note: Use following buttons in the test mode. [GC Test Mode] no mark : Button of amplifier unit (TA-S9D) Enter the GC Test Mode : Button of tuner unit (ST-S9) Procedure 1: : Button of DVD/video CD/CD player unit (DVP-S9) 1.
  • Page 9 TA-S9D MEMO...
  • Page 10: Diagrams

    TA-S9D SECTION 5 DIAGRAMS 5-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Boards: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
  • Page 11: Printed Wiring Boards - Front Amp Section

    TA-S9D 5-2. PRINTED WIRING BOARDS – FRONT AMP Section – • See page 10 for Circuit Boards Location. • Semiconductor Location NO102 Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location D911 C911 D801 D971 Q893 H-10...
  • Page 12: Schematic Diagram - Front Amp Section (1/2)

    TA-S9D 5-3. SCHEMATIC DIAGRAM – FRONT AMP Section (1/2) – (Page 19) (Page 13) (Page 17)
  • Page 13: Schematic Diagram - Front Amp Section (2/2)

    TA-S9D 5-4. SCHEMATIC DIAGRAM – FRONT AMP Section (2/2) – (Page 19) (Page 19) (Page 19) (Page 12) (Page 15) (Page 15)
  • Page 14: Ic Pin Function Description

    TA-S9D 5-5. IC PIN FUNCTION DESCRIPTION 5-6. PRINTED WIRING BOARD – SURROUND AMP Section – • See page 10 for Circuit Boards Location. • FRONT AMP BOARD IC310 PT8300-S (SYSTEM CONTROLLER) Pin No. Pin Name Description — Ground terminal RESET_B...
  • Page 15: Schematic Diagram - Surround Amp Section

    TA-S9D 5-7. SCHEMATIC DIAGRAM – SURROUND AMP Section – (Page 13) (Page 13)
  • Page 16: Printed Wiring Boards - Control Section

    TA-S9D 5-8. PRINTED WIRING BOARDS – CONTROL Section – • See page 10 for Circuit Boards Location. R724 C781 PANEL BOARD MULTI CHANNEL D781 DECODING D704, S712 NO781 D701, S705 JW521 CINEMA STUDIO R715 NO711 D706 D705 D704 D701 R713...
  • Page 17: Schematic Diagram - Control Section

    TA-S9D 5-9. SCHEMATIC DIAGRAM – CONTROL Section – (Page 12)
  • Page 18: Printed Wiring Boards - Power Section

    TA-S9D 5-10. PRINTED WIRING BOARDS – POWER Section – • See page 10 for Circuit Boards Location. (AC IN) AC OUTLET SUB TRANS BOARD NO400 JW803 (E, EA, SP) (AEP, UK, TH, KR, MX, AUS) F900 JW804 JW801 JW907 (E, EA, SP)
  • Page 19: Schematic Diagram - Power Section

    TA-S9D 5-11. SCHEMATIC DIAGRAM – POWER Section – (Page 13) (Page 13) (Page 13) (Page 12)
  • Page 20: Exploded Views

    TA-S9D SECTION 6 EXPLODED VIEWS NOTE: 6-2. FRONT PANEL SECTION • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
  • Page 21: Chassis Section

    TA-S9D 6-3. CHASSIS SECTION not supplied not supplied T911 not supplied not supplied not supplied not supplied not supplied not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
  • Page 22: Electrical Parts List

    TA-S9D SECTION 7 ELECTRICAL PARTS LIST AC INPUT AC OUTPUT FRONT AMP NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 23 TA-S9D FRONT AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C955 1-136-165-00 FILM 0.1uF < GROUND TERMINAL > C956 1-136-165-00 FILM 0.1uF EPT901 1-537-770-21 TERMINAL BOARD, GROUND C961 1-128-563-11 ELECT 100uF 100V EPT902 1-537-770-21 TERMINAL BOARD, GROUND...
  • Page 24 TA-S9D FRONT AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R812 1-260-300-11 CARBON 1/2W R907 1-249-421-11 CARBON 2.2K 1/4W (AEP, UK, KR) (AEP, UK) R814 1-249-437-11 CARBON 1/4W R907 8-719-947-64 DIODE MTZJ-T-72-16A (EXCEPT AEP, UK)
  • Page 25 TA-S9D PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-4727-056-A PANEL BOARD, COMPLETE (TH) A-4727-061-A PANEL BOARD, COMPLETE (AEP, UK) < COIL > A-4727-073-A PANEL BOARD, COMPLETE (EXCEPT AEP, UK, KR) FB707 1-412-473-21 INDUCTOR 0uH (EXCEPT AEP, UK) ********************** <...
  • Page 26 TA-S9D PANEL RELAY SUB TRANS SURROUND AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R740 1-249-441-11 CARBON 100K 1/4W (EXCEPT AEP, UK) < TRANSISTOR > R752 1-249-417-11 CARBON 1/4W Q901 8-729-119-78 TRANSISTOR 2SC2785TP-HFE (EXCEPT AEP, UK) <...
  • Page 27 TA-S9D SURROUND AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > R1063 1-249-429-11 CARBON 1/4W R1065 1-249-433-11 CARBON 1/4W CN1002 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P CN1003 1-770-725-11 CONNECTOR, BOARD TO BOARD 4P...
  • Page 28: Revision History

    TA-S9D REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...