TA-S3 3 7 63 1515 0 SERVICE MANUAL AEP Model UK Model Ver 1.0 2001.05 TA-S3 is the Amplifier section in MHC-S3. SPECIFICATIONS Amplifier section General Power requirements 230 V AC, 50/60 Hz DIN power output (rated) 60 + 60 watts...
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
TA-S3 SECTION 1 SERVICING NOTES 3 7 63 1515 0 This set is a component of the MHC-S3. The MHC-S3 system configuration is as shown below, and there- fore it does not operate normally unless all four components are connected.
TA-S3 SECTION 2 This section is extracted from instruction manual. 3 7 63 1515 0 GENERAL Parts Identification The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for details. Remote Control Main unit...
TA-S3 SECTION 3 DISASSEMBLY 3 7 63 1515 0 • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.
TA-S3 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. COVER 1 three screws 4 Remove the cover (BVTT3 × 6) in the direction of arrow A . 2 two screws (case 3 TP2)
3 7 63 1515 0 TEST MODE Note: Use following buttons in the test mode. [GC Test Mode] no mark : Button of amplifier unit (TA-S3) Enter the GC Test Mode : Button of tuner unit (ST-S3) Procedure 1: : Button of CD unit (CDP-S3) 1.
TA-S3 SECTION 5 DIAGRAMS 3 7 63 1515 0 5-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Boards: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
TA-S3 3 7 63 1515 0 5-9. IC PIN FUNCTION DESCRIPTION • FRONT AMP BOARD IC310 PT8300-S (SYSTEM CONTROLLER) Pin No. Pin Name Description — Ground terminal RESET_B Reset signal input terminal Not used Serial data transfer clock signal input from the tuner unit (ST-S3)
http://www.xiaoyu163.com SECTION 6 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
Page 20
TA-S3 3 7 63 1515 0 6-2. FRONT PANEL SECTION L 13942296513 supplied with S702 (including z A, z B) supplied with S703 supplied with S701 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark u163...
TA-S3 3 7 63 1515 0 6-3. CHASSIS SECTION T911 not supplied not supplied L 13942296513 not supplied not supplied not supplied not supplied not supplied not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety.
TA-S3 SECTION 7 AC INPUT AC OUTPUT 3 7 63 1515 0 ELECTRICAL PARTS LIST FRONT AMP NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Page 27
TA-S3 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.