Noise/Vibration Information; Declaration Of Conformity - Bosch AXT 22 D Original Instructions Manual

OBJ_BUCH-920-003.book Page 7 Tuesday, April 12, 2011 10:04 AM
Technical Data
Quiet-shredder
Article number
Power consumption, S 6
1)
(40/60 s)
Power consumption, S 1
No-load speed
Cutting system
Capacity, max.
Branch diameter, max.
Collection box
Weight according to
EPTA-Procedure 01/2003
Protection class
1)
The S 6 operating mode (40 %) indicates a load profile of 40 s load and 60 s idle time. For practical applica-
tion, continuous operation is permitted.
2)
Depending on the hardness of the wood.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of
unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below
0.36 ohm.

Noise/Vibration Information

Measured sound values determined according to 2000/14/EC
(1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the following
standards or standardization documents: EN 60335, EN 13683 ac-
cording to the provisions of the directives 2004/108/EC,
2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level
Conformity assessment procedure according to Annex V.
Equipment category: 50
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
24.02.2011
Assembly
For Your Safety
Warning! Switch off, remove plug from
mains before adjusting, cleaning or if ca-
ble is cut, damaged or entangled.
Bosch Power Tools
AXT 22 D
3 600 ... H03 0..
W 2200
W 2000
-1
min
Drum
kg/h 180
mm
l
kg 31.3
Observe correct mains voltage: The voltage
of the power source must agree with the volt-
age specified on the nameplate of the unit.
Equipment marked with 230 V can also be
connected to 220 V or 240 V.
Dr. Eckerhard Strötgen
The circuit must at least be protected as fol-
Head of Product
lows:
Certification
AXT 22 D/25 D/23 TC/25 TC = 13 A
An extension cable with a cross section that is
too small causes a distinct reduction in the
performance capabilities of the machine. For
cables to 25 m in length, a cross section of at
least 3 x 1.5 mm
than 25 m in length, the cross section must be
at least 2.5 mm
Cable connections should be kept dry and off
the ground.
AXT 25 D AXT 23 TC
H03 1.. H03 2..
2500 2300
2300 2100
40 40
Drum Turbine
2) 2)
190 215
2) 2)
38 40 42
53 53
31.3 30.5
/I /I
3 600 ... H03 0..
H03 1..
dB(A)
dB(A)
dB
3 600 ... H03 0..
H03 1..
dB(A)
2
is required, for cables more
2
.
WARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight con-
struction and intended for outdoor use.
F 016 L70 737 | (12.4.11)
English | 7
AXT 25 TC
H03 3..
2500
2300
40 40
Turbine
2) 2)
230
2) 2)
45
53 53
30.5
/I /I
H03 2..
H03 3..
81 82
89 90
=3 =2
H03 2..
H03 3..
92 92