Radio Frequency Energy, Certifications Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances. European EMC directive 89/336/EEC CE statement This equipment complies with the requirement for CE mentioned in the European Directive and Standards EN55022 and EN55024.
Overview The LINDY CPU Switch Lite USB allows control of up to 2 computers from one PS/2 or USB keyboard, mouse and monitor. With this unit you can save the cost of additional keyboards, monitors and mice. At the same time you will save space and you will eliminate the problems of using the wrong keyboard or mouse and all the trouble connected with this.
English Manual Operation To switch between the connected computers either press the appropriate switch on the CPU Switch Lite USB or use a hotkey from your PC keyboard. Hot Key control (PC Keyboards only) To send commands to the CPU Switch Lite USB, the 2 seconds.
Page 5
Keyboard Mapping for Mac & Sun Computers The following diagram shows the Hotkey combination that emulates Mac and Sun keyboard commands. This feature is only available on a PS/2 keyboard attached to the CPU Switch Lite USB, and is not available on a USB keyboard.
Sun Microsystems Computers If you use a Sun Microsystems with the CPU Switch Lite USB, you need to switch the console to the Sun Microsystems before you boot up. After you finish booting SUN Microsystems, you can switch the console to the other computer port.
Page 7
English Manual Mac Computers If you apply a PC USB keyboard to USB hub port and a Mac is connected to the CPU Switch Lite USB, then the keyboard will not work correctly as there is no Mac-to-PC keyboard mapping available.
Page 8
Deutsches Benutzerhandbuch Übersicht Der LINDY CPU Switch USB LITE ermöglicht es, 2 PCs von einer USB- oder PS/2-Konsole (Tastatur, Maus, Monitor) aus zu steuern. zusätzliche Tastaturen, Mäuse und vor allem Monitore einsparen. Ferner sparen Sie Platz und Energie ein, die diese zusätzlichen Geräte benötigen würden.
Page 9
Hotkey-Steuerung (nur für PS/2-Tastatur ): Um Kommandos an den CPU Switch USB LITE zu senden, muß die ‚Scroll-Lock’-Taste zweimal innerhalb von 2 Sekunden gedrückt werden. Sie hören dann einen kurzen Quittierungston. Bei Verwendung einer PS/2-Tastatur und -Maus steht an den verbleibenden USB-Ports zusätzlich ein USB-Hub zur Verfügung.
Page 10
Deutsches Benutzerhandbuch Der Auto-Scan-Modus (Der Auto-Scan-Modus funktioniert nur mit zwei eingeschalteten Rechnern) innerhalb 2 sek. Das Scan-Intervall beträgt 5 Sekunden innerhalb 2 sek. Das Scan-Intervall beträgt 10 - 100 Sekunden Ziffer: 1 = 10s, 2 = 20s, 3 = 30s, 4 = 40s, 5 = 50s, 6 = 60s, 7 = 70s, 8 = 80s, 9 = 90s, 0 = 100s Hotkey bei Benutzung einer USB-Tastatur (Diese Funktion steht nur bei PCs zur Verfügung)
Page 11
Fall, verwenden Sie bitte eine andere Tastatur und/oder Maus. Die Maus arbeitet nicht im Auto-Scan-Modus: oder durch Mausklick kehrt der CPU Switch USB LITE vom Auto-Scan- in den Standardmodus zurück, danach sollten Tastatur und Maus wieder einwandfrei arbeiten. Der USB-Hub wird im Auto-Scan-Modus nicht mit umgeschaltet. Nach beliebigem Tastendruck bleibt der momentan angezeigte Port aktiv.
Page 12
USB-Geräte über den Hub ansteuern, kann es zwischen 5 und 10 Sekunden dauern, bis alle USB-Geräte neu initialisiert sind. SUN-Microsystems-Computer: Wenn Sie einen Rechner von Sun mit den CPU-Switch USB LITE benutzen, muß der jeweilige Port beim Booten des Rechners aktiv sein. Nach Beendigung des Systemstarts kann dann geschaltet werden.