Panasonic AW-HE130KP Operating Instructions Manual page 75

Web screen configurations (continued)
Transmission type
Select the transmission format for H.264 images.
Setting value:
Unicast port Up to 14 users can access a single camera at the
(AUTO) same time.
[Unicast port1 (Image)] and [Unicast port2
(Audio)] will be configured automatically when
images and audio are sent from the camera.
We recommend selecting the [Unicast port
(MANUAL)] setting when the port number
transmitting the H.264 images does not need to
be fixed (e.g., during use within a network).
Unicast port Up to 14 users can access a single camera at the
(MANUAL) same time.
[Unicast port1 (Image)] and [Unicast port2
(Audio)] must be configured manually when
images and audio are sent from the camera.
When transmitting H.264 images via the
Internet, configure a fixed transmission port for
the broadband router (hereafter referred to as
"router") (→ page 89). For details, refer to the
operating instructions for the router.
Multicast port An unlimited number of users can access a single
camera at the same time.
When transmitting H.264 images via multicast,
enter the [Multicast address], [Multicast port], and
[Multicast TTL/HOPLimit].
Factory settings: Unicast port (AUTO)
<NOTE>
• For details on the maximum number for simultaneous access, see
(→ page 64).
Unicast port1 (Image) 1
*
Enter the unicast port number (used when sending images from the
unit).
Usable port number range: 1024 to 50000
• Only even numbers can be specified.
• The port number cannot be set to 10670.
Factory settings:
H.264(1): 32004
H.264(2): 32014
H.264(3): 32024
H.264(4): 32034
*
1
The unicast port number must be configured when [Transmission
type] is set to [Unicast port (MANUAL)].
Unicast port2 (Audio)
* 1
Usable port number range: 1024 to 50000
• Only even numbers can be specified.
• The port number cannot be set to 10670.
Factory settings:
H.264(1): 33004
H.264(2): 33014
H.264(3): 33024
H.264(4): 33034
*
1
The unicast port number must be configured when [Transmission
type] is set to [Unicast port (MANUAL)].
Multicast address 2
*
Enter the multicast IP address.
Images and audio will be sent to the specified IP address.
Usable values:
IPv4: 224.0.0.0 to 239.255.255.255
IPv6: Multicast address starting with FF.
Factory settings:
H.264(1): 239.192.0.20
H.264(2): 239.192.0.21
H.264(3): 239.192.0.22
H.264(4): 239.192.0.23
<NOTE>
• Verify usable multicast IP addresses before entering this setting.
Multicast port 2
*
Enter the multicast port number (used when sending images from the
unit).
Usable port number range: 1024 to 50000
• Only even numbers can be specified.
• The port number cannot be set to 10670.
Factory settings: 37004
<NOTE>
• When sending audio from the unit, a port number with "1000" added
to the multicast port number will be used.
Multicast TTL/HOP Limit
* 2
Enter the TTL/HOPLimit value for multicast.
Usable values: 1 to 254
Factory settings: 16
<NOTE>
• When transmitting H.264 images via the Internet, transmitted
images may not appear depending on proxy server settings, firewall
settings, etc. In such cases, consult your network administrator.
• When displaying multicast images on a personal computer with
multiple LAN cards installed, disable the LAN cards that are not
used for reception.
75