Others 3/4 Screen; Others 4/4 Screen - Panasonic AW-HE130KP Operating Instructions Manual

Camera menu items (continued)

Others 3/4 screen

O t h e r s 3 / 4
Wir e l e s s C o n t r o l
OSD M i x
SD I O u t
HD M I O u t
Vi d e o O u t
IP
OSD O f f W i t h T a l l y
OSD S t a t u s
Ret u r n
Wireless Control [Disable, Enable]
"Enable" or "Disable" is set here for operations conducted from the
wireless remote control.
The operations are enabled when the unit's power is turned on from
an external device other than a wireless remote control, and they are
disabled when the power is turned on from a wireless remote control.
<NOTE>
• At the point when this item's setting is changed, the new setting is
not reflected in operation.
It is reflected when the unit is set to the Standby mode and its power
is turned on.
• Follow one of the procedures below if the item's setting is changed
by mistake and the unit can no longer be operated from a wireless
remote control.
When menu operations can be performed using another
control device:
→ F irst change the item using a control device capable of performing
menu operations, and then turn off the unit's power and turn it
back on.
When menu operations cannot be performed using other
control devices:
1. Turn off the power of the units and devices that are connected.
2. Disconnect the unit's power cable, and plug it back in.
3. P erform the operation for turning on the unit's power from the
wireless remote control.
4. A fter changing this item, turn off the unit's power and turn it
back on.
OSD Mix
Select whether to turn off/on camera menu, status, and other displays
for each output image.
SDI Out [Off, On]
HDMI Out [Off, On]
Video Out [Off, On]
IP [Off, On]
The camera menus and statuses are not displayed on the
Off
output pictures targeted by the setting items listed above.
The camera menus and statuses are displayed for the output
On
pictures covered by the setting items listed above.
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 1 minute after the unit is turned on.
OSD Off With Tally [Off, On]
Off or on the function that turns off camera menu, status, and other
displays when tally signals are received via commands or contacts.
When the tally signal releases, the camera menu display will return.
OSD Status [Off, On]
Turn the status display during AWB and ABB off/on.
Return
Return to the previous menu level.
E n a b l e
O n
O n
O n
O n
O f f
O f f
Audio [Off, On]
Input Volume
[Mic High, Mic Middle, Mic Low, Line High, Line Middle,
Line Low]
Plugin Power [Off, On]
Protocol Model Select
[SEVIHD1, SBRC300, SBRCZ330, Reserved1 to Reserved7]
Return

Others 4/4 screen

O t h e r s 4 / 4
A u d i o
I n p u t V o l u m e L i n e M i d d l e
P l u g i n P o w e r
P r o t o c o l
M o d e l S e l e c t
R e t u r n
Turn audio input off/on.
Set the mic input, line input, and volume.
Mic High: Use the mic input with the volume set to high.
Mic Middle: Use the mic input with the volume set to medium.
Mic Low: Use the mic input with the volume set to low.
Line High: Use the line input with the volume set to high.
Line Middle: Use the line input with the volume set to medium.
Line Low: Use the line input with the volume set to low.
Turn the plugin power for the audio off/on.
This is only enabled when [Input Volume] is set to mic input.
Set the protocol model for standard serial communication.
Appears when the service switch (SW4) at the bottom of the unit is
set to ON (standard serial communication).
Do not select [Reserved1] to [Reserved7].
Return to the previous menu level.
O f f
O f f
S E V I H D 1
57