Advertisement
Quick Links
Length
:
Mail Rotor Diameter
Tail Rotor Diameter
Height:
Weight with Battery
Battery
:
11.1V 2200MAH 15C li-polymer
Motor
:
Transmitter
:
Esc
:
Charger
:
DC Li-Po balancing charger
Receiver
:
Servos
:
Specifications
25.8in(655mm)
:
28.3in (720mm)
:
5.3in (135mm)
235MM(9.3 in)
:
670g(23.7oz)
Brushless 2750KV
6 Channel Transmitter
40A brushless esc
6ch receiver
9g x 4pcs
INSTRUCTION MANUAL
INSTRUCTION MANUAL
ITEM NO:DY8918
:
:
:
：
:
:
11.1V 2200MAH 15C
:
:
:
:
:
:
655MM
720MM
135MM
235MM
670g
2750KV
6
LCD
40A
6
9 X4PCS
Advertisement
Related Manuals for Dynam E-Razor
Summary of Contents for Dynam E-Razor
- Page 1 INSTRUCTION MANUAL INSTRUCTION MANUAL ITEM NO:DY8918 Specifications 655MM Length 25.8in(655mm) 720MM Mail Rotor Diameter 28.3in (720mm) 135MM Tail Rotor Diameter 5.3in (135mm) 235MM ： Height: 235MM(9.3 in) 670g Weight with Battery 670g(23.7oz) 11.1V 2200MAH 15C Battery 11.1V 2200MAH 15C li-polymer 2750KV Motor Brushless 2750KV...
- Page 2 Not e: Not e: The Li-Po battery included with your e-razor 3D will arrive partially charged. For this reason the initial charge may only take approximately 3050 minutes. The charger requires up to 3-Amps of 11.515 Volt DC input power that can be supplied by the optional AC to 12V DC, 3-Amp Power Supply for convenient charging anywhere an AC outlet is available.
-
Page 3: Control Test
CONTROL TEST Although each e-razor 3D is control tested at the factory, it is a good idea to test the controls prior to the first flight to ensure none of the servos, linkages or other parts were damaged during shipping and handling. - Page 4 With the stick pushed left, the tail pitch slider should move to the right . PITCH CURVE THROTTLE CURVE 100% TRANSMITTER MANUAL HALF HIGH HALF HIGH STICK POSITION STICK POSITION When be pushed down is IDLE MODE, for 3D flight ,throttle and pitch curve as below: PITCH CURVE THROTTLE CURVE 100%...
-
Page 5: Main Rotor Blade Tracking Adjustment
After powering the model on and allowing the ESC and gyro to properly arm and initialize, bring the main rotor blades of your e-razor 3D up to speed. You can check the blade tracking either on the ground or in the air at approximately eye level. It might be a good... -
Page 6: Parts Listing
Parts Listing Main blade Plastic paddle Tail blade Canopy set 3.Push up throttle sticker , adjustment knob D, let the pitch degree +9-+11. ERZ-001 ERZ-002 ERZ-003 ERZ-004 ERZ-008 Main blade clamp set Main blade housing Seesaw and sf-arm set Washout control arm and washout base set ERZ-005 ERZ-006... - Page 7 UP GRADE PARTS One way bearing Belt Blade holder Bearing 5x11x5 ERZ-0025 ERZ-0026 ERZ-0027 ERZ-0028 ERZ-101 Metal main blade Metal main blade housing Metal Seesaw Metal Sf-arm set clamp set ERZ-102 ERZ-103 ERZ-104 Bearing 3x8x4 and 3x6x2.5 Bearing 2x5x2.5 Bearing 3x8x3 Connecting rod ERZ-0029 ERZ-0030...
- Page 9 3D R/C Helicopter 3D R/C Helicopter S H E N Z H E N D Y N A M S H E N Z H E N D Y N A M I N D U S T R Y & T R A D E C O . , L T D I N D U S T R Y &...