Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for PureAir 3000
Summary of Contents for PureAir 3000
- Page 1 Owner’s Manual...
-
Page 2: Table Of Contents
1 Quick Start Card 1 Owner’s Manual 1 DC POWER ADAPTER 1 REMOTE with Batteries RECORDS Please record the name and phone number of your Dealer. Name: ________________________________________________________________________ Phone #: ______________________________________________________________________ Please record the serial number of your pureAir 3000. Serial #: _______________________________________________________________________... -
Page 3: About
Activated Oxygen, and Filtration you can enjoy noticeably cleaner and fresher air . pureAir 3000 is very easy to set up and use following the instructions included in this manual . After 30 days of continuous use, it will remind you that it needs cleaned by displaying “Perform Cleaning”... -
Page 4: Warnings
WARNINGS Review this list before using or maintaining your purifier! • Never operate purifier near heat source, open flame or flammable/combustible fluids . • Do not operate purifier unless all parts (including PCO CELL, ACTIVATED OXYGEN PLATE, REAR FILTER ASSEMBLY and REAR COVER) are properly installed . -
Page 5: Diagrams
DIAGRAMS - PURIFIER EXTERIOR Front of Purifier Front of Purifier IONIZATION NEEDLE 1. Ionization Needle FRONT GRILLE SCREWS FRONT GRILLE 2. Front Grille Screws CONTROL PANEL 3. Front Grille 4. Control Panel Side of Purifier Side of Purifier REAR COVER 5. - Page 6 DIAGRAMS - PURIFIER INTERIOR/POWER ADAPTER Rear - Rear Cover Removed Rear with REAR COVER Removed BRASS THUMBSCREWS 1. Brass Thumbscrews FILTER ASSEMBLY FILTER ASSEMBLY TABS 2. Filter Assembly 3. Filter Assembly Clasps Rear - Filter Assembly Removed Rear with FILTER ASSEMBLY Removed PCO CELL 4.
- Page 7 DIAGRAMS - CONTROLS Control Panel & Remote CONTROL PANEL & REMOTE POWER BUTTON 1. Power Button SLEEP MODE CONTROL FAN SPEED CONTROL 2. Sleep Mode Control REMINDER RESET BUTTON INFRARED RECEIVER 3. Fan Speed Control PURIFIER LEVEL CONTROL AWAY MODE TOGGLE 4.
-
Page 8: Diagrams
DIAGRAMS - DISPLAY LCD Display DISPLAY FAN SPEED INDICATOR 1. Fan Speed Indicator MODE SPECIFIC DISPLAY MODE INDICATOR 2. Mode Specific Display PURIFICATION LEVEL WARNING MAINTENANCE REMINDERS 3. Mode Indicator AWAY MODE WARNING 4. Purification Level Warning 5. Maintenance Reminders 6. -
Page 9: Setting Up
. Point the purifier towards the center of the room . Never place an operating purifier on the floor . Place Your pureAir 3000 and Plug it In Check to make sure your purifier is secure . Falling purifiers can cause serious headaches! Unravel the cord attached to your DC POWER ADAPTER and your POWER CORD . -
Page 10: Initial Settings
INITIAL SETTINGS Before using your pureAir 3000 you will need to find the area (or square footage) of the environment . To do this accurately, take into account all connected rooms with open doorways (the purification does not flow through closed doors) . The pureAir 3000 can purify up to 3,000 square feet of space . -
Page 11: Controls
CONTROLS Turning the Purifier On/Off Press the POWER BUTTON on the CONTROL PANEL or REMOTE to turn the purifier on . The purifier will initially be set to NORMAL MODE (PCO) . Press the POWER BUTTON once more to turn the power off . Using NORMAL MODE (PCO) Press NORMAL/HIGH MODE TOGGLE until “PCO”... -
Page 12: Disassembly
DISASSEMBLY Tools Required You will need a #2 Phillips screwdriver . Workspace Recommendations A counter top or flat surface is ideal for disassembling/assembling your purifier . You will need 2ft x 3ft of clean, accessible workspace . It is recommended to use a small bowl or cup to hold any screws so they are not lost during the /assembly process . -
Page 13: Disassembly
DISASSEMBLY Removing the PURIFICATION PLATE: Grasp the PURIFICATION PLATE on the ceramic and gently pull it out of the grooves on the sides . Clean (see “CLEANING” page 16) and set the PURIFICATION PLATE aside . Removing the PCO CELL: Locate the PCO CELL CONNECTOR on the right of the rear of the purifier almost halfway up the purifier (beside the PURIFICATION PLATE slot) . -
Page 14: Assembly
ASSEMBLY Refer to “TOOLS & WORKSPACE” from “DISASSEMBLY” on Page 12 Installing the FRONT GRILLE: Gently set the bottom of the FRONT GRILLE in place on the lower front of the purifier and swing the top of the FRONT GRILLE into place, being careful not to damage the IONIZATION NEEDLE at the top center of the front of the purifier . - Page 15 ASSEMBLY Installing the FILTER ASSEMBLY: Hold the FILTER ASSEMBLY with the larger flat side (where the honeycomb layer of the filter is visible) facing the interior of the purifier . Insert the bottom of the FILTER ASSEMBLY into the tabs on the rear of the purifier and then seat the FILTER ASSEMBLY on the rear of the purifier .
-
Page 16: Cleaning
CLEANING Your purifier should be cleaned at least monthly to keep it running at peak performance, but more often if its operating environment is heavily contaminated . Cleaning the Purifier (Exterior): Wipe down the exterior with a damp cloth or use compressed air or a vacuum cleaner to remove dust . -
Page 17: Troubleshooting
TROUBLESHOOTING The Purifier Fails to Turn On Verify that the POWER PLUG is plugged into an operational wall outlet . Ensure that the POWER CORD is fully inserted (leaving less than an 1/8”) into the DC POWER ADAPTER and the green light on the DC POWER ADAPTER is illuminated . -
Page 18: Troubleshooting
TROUBLESHOOTING The IONIZATION NEEDLE Creates an Electrical Arc: The IONIZATION NEEDLE needs to be cleaned . Using a cotton swab soaked with rubbing alcohol, gently clean around the IONIZATION NEEDLE . The Fan Does Not Operate Properly: Try adjusting the fan speed using the CONTROL PANEL or REMOTE CONTROL . Remove the FRONT GRILLE (see “DISASSEMBLY”... -
Page 19: Warranty
LIMITED WARRANTY INFORMATION Your pureAir 3000 Whole Home Air Purifier (Product) is warranted to be free from all defects in material and workmanship in normal household use for a period of 1 Year from date of purchase . The warranty is granted only to the original purchaser . The warranty is subject to... -
Page 20: Accessory Products
ACCESSORY PRODUCTS To maximize the effectiveness of your pureAir 3000 we recommend the use of . . . Ozone Plate Cleaning Kit • Deeper, more effective cleaning than scrubbing . • Convenient and simple cleaning procedure . • Dramatically increased ozone plate life span .
Need help?
Do you have a question about the 3000 and is the answer not in the manual?
Questions and answers
Pureair 3000. New poc installed. Light comes on, **** starts but quits. No obstruction in ****.
The PureAir 3000 could start and then quit after a new PCO CELL installation if the BRASS THUMBSCREWS or PCO CELL RETAINING NUTS have become loose during shipment or storage. These components should be checked and tightened properly to ensure the unit functions correctly.
This answer is automatically generated