LCD TV SERVICE MANUAL CHASSIS : ML-041A MODEL : RM-32LZ50 CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Page 2
If you need more information on Computer and Electronic Repair, please visit these websites to improve yourself. http://www.fastrepairguide.com http://www.protech2u.com http://www.plasma-television-repair.com http://www.lcd-television-repair.com Happy Repairing!! Highly Recommended Repair Ebook: If you’re a LCD Monitor repairer, then this is the best guide for you. Why? Because, the author revealed all his LCD Monitor Repairing secrets for you.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 6
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range This specification is applied to ML-041A chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ±...
Page 8
5.General Specification(Monitor) Item Specification Unit Remark Panel 32” TFT WXGA LCD Frequency range DVI-I input H: 31 ~ 61KHz, V: 56 ~ 75Hz 1) Contrast/ Brightness Control function 2) H- Position/ V-Position 3) Tracking : Clock/Phase 4) Auto Configure 5) Reset 1: Y Component Jack 3: Pb...
Page 9
6.Optical Feature(LCD Module) Item Specification Remark Viewing Angle R/L, U/D 176,176 <CR 10> Luminance Luminance(cd/ ) Typical Variation MAX/MIN Contrast Ratio ALL white/All back CIE Color Coordinates WHITE Typ. 0.285 Typ. 0.293 Typ. 0.640 Typ. 0.341 Green Typ. 0.287 Typ. 0.610 Blue Typ.
Page 10
8.Component Video Input (Y, P Resoluton H-freq(kHz) V-freqHz) Pixel clock Proposed 640 x 480 15.73 60.00 SDTV. DVD 480i RZ, RT, RM 640 x 480 15.63 59.94 SDTV. DVD 480i RZ, RT, RM 704 x 480 31.47 59.94 EDTV 480p RT, RM 720 x 576 15.625...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Total Period Back Porch Video Active Time Front Porch Sync Duration Sync Mode Resolution Frequency Clock Polarity Sort 31.469 25.175 640x480 –...
ADJUSTMENT INSTRUCTION 1. Application Object 2.2.1 EDID DATA [DDC DATA Analog] This instruction is for the application to the LCD TV. 01 02 03 07 08 09 0A 0B 0C 0D 0E 0F FF FF FF FF FF FF 00 1E 6D 45 75 01 01 2.
Page 13
3. Shipping Conditions ITEM CONDITION REMARK Power Volume Level Main Pcture Input Main Last Channel Pr 01 Mute 16:9 Station Auto Program Manual Program Program Edit Favorite Program None Picture Dynamic Dynamic Contrast Brightness Colour Sharpness NTSC OPTION Tint Sound Flat Balance Special...
Page 14
*Option(PAL) ITEM CONDITION REMARK ITEM CONDITION REMARK Option 1 Option 3 Side AV 0: Side AV Off Language 0: Eng Only 1: Side AV On 1: EU5 SCART 0: SCART Off 2: 12 nations(Europe) 1: SCART On 3: Eng + Chines 0: PC Off 4: Eng + Arab + Urdu 1: PC On...
Page 16
EDID ADJUSTMENT Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
SVC REMOCON FUNTION REAMARK To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function.
TROUBLESHOOTING No power :[A]Process (LED indicator off) Check short of main B/D Check 24V or 12V or Change Power B/D Faill of Power B/D Pass Check Output of Change L3, L1300 Faill L3, L1300 Pass Check Output of Change L808,L809 Change IC1300,IC4 or IC8 IC1300, IC4 or IC8 (F801,F802)
Page 19
No Raster :[B]Process Check LED Status Repeat A PROCESS on display unit Faill Check L900,L901 Change L900,L901, L902,L903 L902,L903 Faill Pass Check the input/ Change IC901 Output of IC901 Faill Pass Check inverter Change inverter Connector or inverter connector or inverter Faill Pass Change panel link...
Page 20
No Raster on Component signal Repeat [A] Process Pass Check the signal of Change Q310,Q315,Q316 Q310,Q315,Q316 Faill Pass Re-soldering or Check the input/ Change the defect part Faill output of IC1 Re-soldering or Check the input/output Change the defect part Faill of IC500, IC600 Pass...
Page 21
No Raster on AV Signa No Raster on TV(RF) signal (Video1,Video2, S-Video) Check 5V, 33V of TU1000 Repeat Check the output of Re-soldering or [A] Process TU1000 Faill Faill Change the defect part Pass Check the signal of Change C316,C317, C316,C317,Q308,Q313 Q308,Q313 Faill...
Page 22
No Sound Check the Change source input input source Faill Pass Re-soldering or Check the input/output Change the defect part of IC1 Faill Pass Re-soldering or Check the input/output Change the defect part of IC100,IC101 Faill Pass Check the speaker Change speaker Faill Pass...
Page 24
BLOCK DIAGRAM DESCRIPTION 1. Video controller unit and display data conversion unit The video controller unit recives the video signal input from the tuner, AV port (CVBS ,S-Videoand component ). Comb fiter separates the YC component. The composite signal from the vcti goes to the 3-D comb filter and comb filter gives YC signal as output which goes back to the Vcti.
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)
Page 36
R1606 0RD1500Q609 150 1/4W(3 5% TA52 R966 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP SW1600 140-313A TACT 2LEAD 100G(TA) LG C&D NO R967 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP LED1600 0DLBE0128AA BRIGHT LED ELECTRONICS BL-BUB R968 0RJ0222D677...
Page 39
Oct., 2004 P/NO : 3828TSL108L Printed in Korea...
Page 40
If you need more information on Computer and Electronic Repair, please visit these websites to improve yourself. http://www.fastrepairguide.com http://www.protech2u.com http://www.plasma-television-repair.com http://www.lcd-television-repair.com Happy Repairing!! Highly Recommended Repair Ebook: If you’re a LCD Monitor repairer, then this is the best guide for you. Why? Because, the author revealed all his LCD Monitor Repairing secrets for you.