Page 1
- Appliance White 14.4 Net Weight: Lbs. Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., Eastern, Monday-Friday • Español - página 25 1-800-654-3545 • Français - page 49 www.emersonfans.com Part No.
3. Do not put anything into the fan blades while they are WARNING: To avoid fire, shock or injury, do not use an turning. Emerson or any other brand of control not specifically 4. Do not operate reversing switch until fan blades have approved for this fan.
Emerson Electric Co. Substitution of parts or accessories not designated for use with this product Fan Blade Flanges by Emerson Electric Co. could result in personal injury or property damage. Fan Blades NOTE: If you are uncertain of part description, refer Check to see that you have received the following parts: to exploded view illustration below.
Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned Please call Emerson technical support off at the main fuse box before wiring. All wiring must 1-800-654-3545 if you have any questions about be in accordance with National and Local codes and installation and operation of this ceiling fan.
3. Ceiling Fan Assembly WARNING Turning off wall switch is not sufficient. To avoid Disconnect electrical power to the branch circuit at the possible electrical shock, be sure electricity is turned circuit breaker or fuse box before attempting to install off at the main fuse box before wiring.
Page 6
3. Ceiling Fan Assembly (Continued) DOWNROD HAIRPIN CLIP Loosen the two setscrews in the motor coupling. CLEVIS Place the hanger ball/4.5” downrod assembly into the motor coupling, aligning the clevis pin holes in the CLEVIS downrod with the holes in the motor coupling (Figure 3). HAIRPIN CLIP The clevis pin must go through the holes in the motor...
Page 7
3. Ceiling Fan Assembly (Continued) The fan comes with blue, black and white leads that are 6 to 9 42” long. INCHES Measure up approximately 6 to 9-inches above top of hanger ball/4.5” downrod assembly (Figure 5). HANGER BALL/ Cut off excess leads and strip back insulation 1/2-inch DOWNROD from end of leads.
Page 8
3. Ceiling Fan Assembly (Continued) M5 x 6mm WASHER HEAD Mount the blade flange to the fan blade using three BLADE SCREW (3) M5 x 6mm washer head screws (supplied) (Figure 8). Repeat this procedure for other four fan blades and blade flanges.
Page 9
Remove the three switch housing mounting screws MOUNTING PLATE (Figure 10) from the switch housing plate. NOTE: If you are using an Emerson light fixture Retain the screws for future use in Step 3.13. with your fan. Remove the screw plug from the...
Page 10
3. Ceiling Fan Assembly (Continued) 3.13 Position the switch housing assembly on the switch housing plate and align the holes in the switch housing SWITCH assembly with the holes in the plate. HOUSING ASSEMBLY Secure the switch housing assembly by reinstalling the three mounting screws (previously removed) NOTE: Do not pinch wires between the switch (Figure 12).
4. How to Hang Your Ceiling Fan WARNING CEILING The fan must be hung with at least 7' of clearance from floor to blades (Figure 12). AT LEAST FLOOR Figure 13 WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs.
Page 12
4. How to Hang Your Ceiling Fan (Continued) NOTE: SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY. Carefully lift the fan and seat the hanger ball/ downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 15). Be sure the OUTLET groove in the ball is engaged with the anti-rotation tab on the hanger bracket (Figure 15).
Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage. Securely connect the fan motor white wire to the supply...
Page 14
5. How to Wire Your Ceiling Fan (Continued) Securely connect the fan motor black wire and blue wires to the supply black (hot) wire using wire FAN MOTOR connector (supplied) (Figure 18). BLACK WIRE SUPPLY BLACK (HOT) LISTED WIRE CONNECTOR FAN MOTOR BLUE WIRE Figure 18...
Page 15
5. How to Wire Your Ceiling Fan (Continued) Screw the two threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 20). THREADED STUDS (2) Figure 20 Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling CEILING COVER cover (Figure 21).
6. Using Your Ceiling Fan Restore electrical power to the outlet box by turning the electricity on at the main fuse box. Check the operation of the fan by gently pulling on the pull chain switch. All fans are shipped from the factory with the reversing switch positioned to the “left”...
WARNING Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury The use of any other control not specifically approved or property damage. for this fan could result in fire, shock and personal injury.
10. Trouble Shooting WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Reversing switch in neutral position. 1. Make sure reversing switch position is all the way to one side.
8 - 9 feet above the floor for optimal occupied space. Remember to adjust your thermostat airflow. Consult your Emerson Retailer for optional when using your ceiling fan - additional energy and mounting accessories.
What We Will Do To Correct Problems: If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during the expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or workmanship, you must contact Emerson during the applicable warranty period.
Page 24
Air Comfort Products DIVISION OF EmErSON ElEctrIc cO. 8100 W. Florissant • St. louis, mO 63136 Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., Eastern, Monday-Friday 1-800-654-3545 www.emersonfans.com Retain this manual for future use.