Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Allnet Manuals
  4. IP Camera
  5. ALL2295
  6. User manual

Allnet ALL2295 User Manual

Full hd vandal proof ip outdoor dome camera
Hide thumbs

Advertisement

Quick Links

Download this manual
ALL2295
Full HD Vandal Proof IP Outdoor Dome Camera
User's Manual
V1.0

Advertisement

loading
Need help?

Need help?

Do you have a question about the ALL2295 and is the answer not in the manual?

Questions and answers

Related Manuals for Allnet ALL2295

Summary of Contents for Allnet ALL2295

  • Page 1 ALL2295 Full HD Vandal Proof IP Outdoor Dome Camera User’s Manual V1.0...
  • Page 2 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Table of Contents...
  • Page 3 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 4 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Full HD Vandal Proof IP Dome Camera is capable of serving real-time streaming and makes image quality more smoothly. In addition to MJPEG real time streaming, this camera develops H.264 codec to apply for high resolution digital broadcast.
  • Page 5 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Please check the package contains the following items listed below. Camera Package Contents DC Jack Cable Vandal Proof IP Dome Camera Security Torx Power Terminal Block Self Tapping Rubber Washers (× Plastic Screw Screws Anchors...
  • Page 6 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 This chapter will provide the camera dimensions for reference before installation. Definition of each connector on the camera’s PCB board will also be specified. The IP Dome Camera’s dimensions are shown below. Top View Side View...
  • Page 7 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The diagram below shows the IP Dome Camera’s reset button and various connectors. Definition for each connector will be given as follows.
  • Page 8 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Connector Pin No. Definition Remarks Reset Button Restore to factory default Analog Video Output Output＋ Output－ Alarm I/O Alarm connection Input＋ Input－ Input Two-way audio Audio I/O Output transmission Output (L) Power Reserved Power-1...
  • Page 9 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 To perform the IP Camera via web browser, please ensure your PC is in good network connection, and meet system requirements as described below. Items System Requirement ○, ○, ○, 1.
  • Page 10 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 For users who have installed the DC Viewer in the PC previously, please first delete the existing DC Viewer from the PC before accessing to the IP Camera. Deleting the DC Viewer Click “Control Panel”, and then double click “Add or Remove Programs.”...
  • Page 11 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 STEP 1: Click the “Tools” tab and select the option “Internet Options.” STEP 2: Click on “Delete”, then tap the “Delete Files” in the “Temporary Internet files” section.
  • Page 12 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 13 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The popup window for confirmation will come out as shown below. Click “Yes” to start deleting the files.
  • Page 14 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Please read the instructions provided in this chapter thoroughly before installing the Full HD Multi-Res Vandal Proof IP Dome Camera. Power Connection Make sure the camera’s power cable is correctly and firmly connected; refer to the pin definition table in section 2.2 Camera’s Connectors.
  • Page 15 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Vandal Proof IP Dome Camera can be installed directly on a wall or ceiling. Please note that the wall or ceiling must have enough strength to support the IP Dome Camera. Follow the steps below to install the IP Dome Camera: Step 1: Unpack the Vandal Proof IP Dome Camera package and take out the...
  • Page 16 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 4: Unscrew the module-fastened screw, as indicated in the figure. Step 5: Press the sides of the snap-on module, as indicated in the figure, and detach it from the Dome Camera’s housing.
  • Page 17 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 9: Fasten the Dome Camera’s housing with the four equipped self tapping screws. Step 10: Thread the power and Ethernet cables through either the side conduit entry or back conduit entry, as illustrated.
  • Page 18 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 13: Connect the power and network outputs. NOTE: The Power Cable is omitted if using PoE. STEP 14: Access the camera browser-viewer for viewing images. Please refer 6. Accessing Camera for further details.
  • Page 19 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 16: Adjust the camera to a desired angle, as shown below. Pan adjustment range is nearly 360°; rotation angle range approaches to 270°. Tilt is adjustable between ﹣10° ~ 90°. Pan Adjustment Rotation Adjustment Tilt Adjustment...
  • Page 20 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 STEP 19: Screw on the two Torx screws on the side of the Dome Cover tightly to fasten the Dome Cover. Camera installation is complete.
  • Page 21 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Before installing the IP Dome Camera in the 4S Electrical Box, please unscrew and open the Dome Cover with the Security Torx. Figure: 4S Mount Electrical STEP 1: Run the wires (Ethernet and power) through the wall. NOTE: The power cable is omitted if using PoE.
  • Page 22 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 STEP 4: Thread the power and Ethernet cables through either the side conduit entry or back conduit entry. Then fasten the Dome Camera’s housing on the Electrical Box with the two screws.
  • Page 23 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 STEP 10: Replace the Dome Cover back, aligning the arrow mark on the Dome Cover with the one on the housing. STEP 11: Screw on the two Torx screws on the side of the Dome Cover tightly to fasten the Dome Cover.
  • Page 24 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 For initial access to the IP Camera, users can search the camera through the installer program: DeviceSearch.exe, which can be found in “DeviceSearch” folder in the supplied CD. Device Search Software Setup Step 1: Double click on the program Device Search.exe (see the icon below);...
  • Page 25 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Device Search Step 3: Click “Device Search” again, and all the finding IP devices will be listed in the page, as shown in the figure below. The Camera don’t have a default IP Adress.
  • Page 26 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The default login ID and password for the Administrator are: Login ID Password admin admin NOTE: ID and password are case sensitive. NOTE: It is strongly advised that administrator’s password be altered for the security concerns.
  • Page 27 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 2: The “Network Setup” page will come out. Select “DHCP,” and press “Apply” button down the page. Step 3: Click “OK” on the Note of setting change. Wait for one minute to re- search the IP Camera.
  • Page 28 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 4: Click the “Device Search” button to re-search all the devices. Then select the IP Camera with the correct MAC address. Double click on the IP Camera, and the login window will come out. Step 5: Enter User name and Password to access the IP Camera.
  • Page 29 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 permission to install the ActiveX Control for displaying video in browser (see the figure below). Right click on the Information Bar and select “Install ActiveX Control…” to allow the installation. Then the security warning window will pop up.
  • Page 30 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Vari-focal Model...
  • Page 31 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Motorized Model Administrator/User Privileges “Administrator” represents the person who can configure the IP Camera and authorize users access to the camera; “User” refers to whoever has access to the camera with limited authority, i.e. entering Home and Camera setting pages.
  • Page 32 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The IP Camera is provided with a user-friendly browser-based configuration interface, and a free bundled CMS (Central Management System) for video playback and recording. In this chapter, information about main page introduction, system related settings and camera settings will be described in detail.
  • Page 33 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 There are five tabs: Home, System, Streaming, Camera and Logout on the top panel. Home Users can monitor live video of the targeted area. System setting The administrator can set host name, system time, root password, network related settings, etc.
  • Page 34 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 In the Home page, there are several function buttons right down the displayed image. Multiple Languages Support Multiple languages are supported, including German, English, French, Italian, Russian, etc., for the viewer window interface. Screen Size Adjustment Image display size can be adjusted to x1/2 and full screen.
  • Page 35 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Talk button (on/off) Talk function allows the local site to talk to the remote site. Click on the button to switch it to on/off. Please refer to section 7.3.2 Security: Add user >>...
  • Page 36 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Multiple Languages Support Multiple languages are supported, including German, English, French, Italian, Russian, etc., for the viewer window interface. Screen Size Adjustment Image display size can be adjusted to x1/2 and full screen. Digital Zoom Control In the full screen mode, users can implement digital PTZ by rotating the mouse wheel (for zoom in/out), and drag the mouse into any direction.
  • Page 37 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Speaker button (on/off) Press the Speaker button to mute/activate the audio. Snapshot button Press the button, and the JPEG snapshots will automatically be saved in the appointed place. The default place of saving snapshots is: C:\. To change the storage location, please refer to section 7.3.13 File Location further details.
  • Page 38 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Tele/Wide Steps buttons Pressing the Tele/Wide Steps buttons will lead zoom to be shifted toward Tele/Wide sides in user-defined range, which can be selected from the drop-down menu.
  • Page 39 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Near/Far Steps buttons Pressing the Near/Far buttons will lead focus to be altered toward Near/Far sides in user-defined range, which can be selected from the drop-down menu. Push AF button Please press the Push AF button once Zoom or Focus is adjusted.
  • Page 40 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The figure below shows all categories under the “System” tab. Each category in the left column will be explained in the following sections. NOTE: The “System” configuration page is only accessible by Administrator.
  • Page 41 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Press the first category: <System> in the left column; the page is shown as below. Host Name The name is for camera identification. If alarm function (see section 7.3.7 Application) is enabled and is set to send alarm message by Mail/FTP, the host name entered here will display in the alarm message.
  • Page 42 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Sync With Computer Time Select the item, and video date and time display will synchronize with the PC’s. Manual The Administrator can set video date, time and day manually. Entry format should be identical with that shown next to the enter field.
  • Page 43 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Click the category: <Security>, there will be a drop-down menu with tabs including <User>, <HTTPS>, <IP Filter>, and <IEEE 802.1X>.
  • Page 44 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 7.3.2.1 User Click the <User> tab under the category <Security> and the page is shown as the figure below. Root password Change the administrator’s password by inputting the new password in both text boxes.
  • Page 45 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 displayed in the user name list. There is a maximum of twenty user accounts. Each user can be assigned the privileges of “Camera control”, “Talk” and “Listen”.  I/O access This item supports fundamental functions that enable users to view video when accessing to the camera.
  • Page 46 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 47 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 7.3.2.2 HTTPS <HTTPS> allows secure connections between the IP Camera and web browser using <Secure Socket Layer (SSL)> or <Transport Layer Security (TLS)>, which ensure camera settings or Username/ Password info from snooping.
  • Page 48 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Create Self-signed Certificate Before a CA-issued certificate is obtained, users can create and install a self-signed certificate first. Click <Create> button under “Create self-signed certificate” and provide the requested information to install a self-signed certificate for the IP Camera. Please refer to the last part of this section: Provide the Certificate Information...
  • Page 49 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Create Certificate Request Click the “Create Certificate Request” button to create and submit a certificate request in order to obtain a signed certificate from CA. Provide the request information in the create dialog. Please refer to the following Provide the Certificate Information for more details.
  • Page 50 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Provide the Certificate Information To create a Self-signed HTTPS Certificate or a Certificate Request to CA, please enter the information as requested:...
  • Page 51 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 52 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Country Enter a 2-letter combination code to indicate the country the certificate will be used in. For instance, type in “US” to indicate United States.  State or province Enter the local administrative region.
  • Page 53 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Valid days (Self-signed Certificate Only) Enter the period in days (1~9999) to indicate the valid period of certificate. Click “OK” to save the Certificate Information after complete. 7.3.2.3 IP Filter Using the IP filter, access to the IP Camera can be restricted by denying/allowing specific IP addresses.
  • Page 54 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Add/ Delete IP Address Input the IP address and click the <Add> button to add a new filtered address. The Filtered IP Addresses list box shows the currently configured IP addresses.
  • Page 55 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 CA Certificate The CA certificate is created by the Certification Authority for the purpose of validating itself. Upload the certificate for checking the server’s identity. Client Certificate/ Private Key Upload the Client Certificate and Private Key for authenticating the IP Camera itself.
  • Page 56 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Click the category: < Network>, there will be a drop-down menu with tabs including <Basic>, <QoS>, <SNMP>, and <UPnP>.
  • Page 57 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 7.3.3.1 Basic Users can choose to connect to the IP Camera with fixed or dynamic (DHCP) IP address. The IP Camera also provides PPPoE (Point-to-Point Protocol over Ethernet) support for users who connect to the network via PPPoE.
  • Page 58 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Use fixed IP address To setup static IP address, select “Use fixed IP address” and move the cursor to the IP address blank (as indicated below) and insert the new IP address, ex.

  • Page 59: Use Pppoe

    Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  IP address This is necessary for network identification.  Subnet mask It is used to determine if the destination is in the same subnet. The default value is “255.255.255.0”. ...
  • Page 60 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 NOTE: Be aware to assign a different port number for each separate service mentioned above. IPv6 Address Configuration With IPv6 support, users can use the corresponding IPv6 address for browsing. Enable IPv6 by checking the box and click “Save” to complete the setting.

  • Page 61: Snmp (Simple Network Management Protocol)

    Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The DSCP value range is from 0 to 63. The default DSCP value is 0, which means DSCP disabled. The IP Camera uses the following QoS Classes: Video, Audio and Management.
  • Page 62 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 63 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 SNMP v1/ v2  Enable SNMP Select the version of SNMP to use by checking the box.  Read Community Specify the community name that has read-only access to all supported SNMP objects.
  • Page 64 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 7.3.3.4 UPnP UPnP Setting  Enable UPnP When the UPnP is enable, whenever the IP Camera is presented to the LAN, the icon of the connected IP Cameras will appear in My Network Places to allow for direct access as shown below.
  • Page 65 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 66 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 NOTE: To enable this function, please make sure the UPnP component is installed on your computer. Please refer to Appendix D: Install UPnP components for UPnP component installation procedure.
  • Page 67 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Enable UPnP port forwarding When the UPnP port forwarding is enabled, the IP Camera is allowed to open the web server port on the router automatically. NOTE: To enable this function, please make sure that your router supports UPnP and it is activated ...
  • Page 68 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Enable DDNS Check the item to enable DDNS. Provider Select one DDNS host from the provider list. Host name Enter the registered domain name in the field. Username/E-mail Enter the username or e-mail required by the DDNS provider for authentication.
  • Page 69 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when an alarm is triggered. SMTP is a protocol for sending e-mail messages between servers. SMTP is a relatively simple, text-based protocol, where one or more recipients of a message are specified and the message text is transferred.
  • Page 70 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Administrator can set as sending alarm message to a specific File Transfer Protocol (FTP) site when an alarm is triggered. Users can assign alarm message to up to two FTP sites. The FTP setting page is shown below.
  • Page 71 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 A HTTP Notification server can listen for notification messages from IP Cameras by triggered events. The HTTP setting page is shown below. Enter the HTTP details, which include server, user name, and password in the fields.
  • Page 72 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The IP Camera equips one alarm input and one relay output for cooperating with alarm system to catch events’ images. Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed. The alarm configuration page is also shown below.
  • Page 73 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Alarm Switch The Administrator can enable or disable the alarm function. Alarm Type Select an alarm type, “Normal close” or “Normal open,” that corresponds with the alarm application. Alarm Output Define alarm output signal “high”...
  • Page 74 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Record Stream to SD Card Select the item and the alarm-triggered recording will be saved into your Micro SD card.
  • Page 75 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 NOTE: Please make sure the local recording (with Micro SD/ SDHC card) is activated so that this function can be implemented. See section 7.3.12 Recording for further details.
  • Page 76 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Upload Image by E-Mail Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When the alarm is triggered, event images will be sent to the appointed e-mail address. NOTE: Make sure SMTP or FTP configuration has been completed.
  • Page 77 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Send HTTP notification Check this item, select the destination HTTP address, and specify the parameters for event notifications by <Alarm> triggered. When an alarm is triggered, the notification can be sent to the specified HTTP server.
  • Page 78 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Add sequence number suffix (limited value) File Name: imageXX.jpg X: Sequence Number The file name suffix will end at the number being set. For example, if the setting is up to “10,” the file name will start from 00, end at 10, and then start all over again.
  • Page 79 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Motion Detection function allows detecting suspicious motion and triggering alarms when motion volume in the detected area reaches/exceeds the determined sensitivity threshold value. In the Motion Detection setting page, there is a frame (Motion Detection Window) displayed on the Live Video Pane.
  • Page 80 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 If Motion Detection function is activated, the pop-off window (Motion) with indication of motion will be shown. When motion is detected, the signals will be displayed on the Motion window as shown below. Detailed settings of Motion Detection are described as follows: Motion Detection You will be able to turn on/off Motion Detection in System section.
  • Page 81 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Sensitivity level [1-100]: The default level is 80, which means if 20% or more sampling pixels are detected differently, system will detect motion. The bigger the value, the more sensitive it is. Meanwhile, when the value is bigger, the red horizontal line in the motion indication window will be lower accordingly.
  • Page 82 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Upload Image by FTP Select this item, and the Administrator can assign a FTP site and configure various parameters as shown in the figure below. When motion is detected, event images will be uploaded to the appointed FTP site.
  • Page 83 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Send HTTP notification Check this item, select the destination HTTP address, and specify the parameters for event notifications by <Motion Detection> triggered. When an alarm is triggered, the notification can be sent to the specified HTTP server.
  • Page 84 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Tempering Alarm function helps the IP Camera against tampering such as deliberate redirection, blocking, paint spray, and lens cover, etc through video analysis and reaction to such events by sending out notifications or uploading snapshots to the specified destination(s).
  • Page 85 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 interpreted as defining the Tampering threshold; longer duration represents higher threshold. Settable Tampering Duration time range is from 10 to 3600 seconds. Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when tampering is detected.
  • Page 86 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Upload Image by E-Mail Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When tampering is detected, event images will be sent to the appointed e- mail address.
  • Page 87 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Users can implement local recording to the Micro SD/SDHC card up to 16GB. This page shows the capacity information of the Micro SD card and a recording list with all the recording files saved on the memory card. Users can also format the SD card and implement automatic recording cleanup through the setting page.
  • Page 88 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 When users insert the Micro SD/SDHC card, the card information such as the memory capacity and status will be shown at Device Information section. For the memory card being successfully installed, its status shall be shown at “Device information”...
  • Page 89 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0  Download To open/download a video clip, select the file first, and then press the “download” button below the Recording list field. The selected file window will pop up as shown below. Click on the AVI file to directly play the video in the player or download it to a specified location.
  • Page 90 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 In the Recording setting page, users can specify the recording schedule that fits the present surveillance requirement. Activating Micro SD/SDHC Card Recording Two types of schedule mode are offered: Always and Time Frame setting. Users can setup the time frame to fit the recording schedule or choose “Always”...
  • Page 91 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Users can specify a storage location for the snapshots and web recording. The default setting is: C:\. Once confirm the setting, press “Save,” and all the snapshots and recording will be saved in the designate location. NOTE: Please make sure the selected file path contains valid characters such as letters and numbers.
  • Page 92 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 For users who use Auto-iris lens, when it is required to implement iris adjustment, please refer to the Iris adjustment procedure in the setting page to adjust iris.
  • Page 93 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Click on the link to view the system log file. The content of the file provides useful information about configuration and connections after system boot-up.
  • Page 94 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Administrator can view each added user’s login information and privileges (see 7.3.2 Security). View User Login Information All the users in the network will be listed in the “User information” zone, as shown below.
  • Page 95 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 View User Privilege Press “get user privacy” down the page, and the Administrator can view each user’s privileges. As the figure above shows: User: 1:1:0:1 1:1:0:1= I/O access : Camera control : Talk : Listen (see 7.3.2 Security) Therefore, it denotes the user is granted privileges of I/O access, Camera...
  • Page 96 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Click on this item to view the entire system’s parameter setting.
  • Page 97 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The factory default setting page is shown as below. Follow the instructions to reset the IP Camera to factory default setting if needed. Set Default Click on the “Set Default” button to recall the factory default settings. Then the system will restart in 30 seconds.
  • Page 98 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The current software version is displayed in the software version page, which is shown as the figure below.
  • Page 99 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Software upgrade can be carried out in the “Software Upgrade” page, as shown below. NOTE: Make sure the upgrade software file is available before carrying out software upgrade.
  • Page 100 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The procedure of software upgrade is like the following: Step 1: Click “Browse” and select the binary file to be uploaded, ex. Userland.jffs2. NOTE: Do not change the upgrade file name, or the system will fail to find the file.
  • Page 101 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 After the upgrade process is finished, the viewer will return to Home page. Step 4: Close the video browser. Step 5: Click “Control Panel”, and then double click “Add or Remove Programs.”...
  • Page 102 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera. Export Users can save the system settings by exporting the configuration file (.bin) to a specified location for future use.
  • Page 103 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Upload To copy an existing configuration file to the IP Camera, please first click on “Browse” to select the configuration file, and then press the “Upload” button for uploading.
  • Page 104 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Press the tab “Streaming” in the top of the page, and the configurable video and audio items will display in the left column. In Streaming, the Administrator can configure specific video resolution, video compression mode, video protocol, audio transmission mode, etc.
  • Page 105 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Video Format Resolution for MJPEG & H.264 format includes:  H.264 720p (30fps) + MJPEG 720p (30fps)  H.264 720p (30fps) + MJPEG D1 (30fps)  H.264 720p (30fps) + MJPEG CIF (30fps) ...
  • Page 106 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 To rotate the image, users can select “Flip”, for instance. Then the displayed image will be reversed as shown below. The following is descriptions for different video rotate type.  Flip If select <Flip>, the image will be rotated vertically.
  • Page 107 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 decreasing the frequency of I-frames. Click “Save” to confirm the GOV setting.
  • Page 108 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Users can specify the values for MJPEG/H.264 compression mode in the video compression page (see the figure below), depending on the application. MJPEG Q (Quality) factor Higher value implies higher bit rates and higher visual quality. The default setting of MJPEG Q factor is 35;...
  • Page 109 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 CBR Mode Setting The CBR (Constant Bit Rate) mode could be the preferred bit rage mode if the bandwidth available is limited. It is important to take account of image quality while choosing to use CBR mode.
  • Page 110 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 In the Video OCX protocol setting page, users can select RTP over UDP, RTP over TCP, RTSP over HTTP or MJPEG over HTTP, for streaming media over the network. In the case of multicast networking, users can select the Multicast mode.
  • Page 111 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Video frame skipping is for saving bandwidth, if necessary. The setting page is shown as below. Video Frame Skip options include:  No skipping, default  Frame skipping at 2 frame internal ...
  • Page 112 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Active Mask Function  Add a Mask Check a Video Mask checkbox, and a red frame will come out in the Live Video pane at the right side. Use the mouse to drag and drop to adjust the mask’s size and place it on the target zone.
  • Page 113 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 blue, cyan, and magenta.  Type Select to change the mask type as solid or transparent. Click “Save” to confirm the setting. The audio setting page is show as below. In the Audio page, the Administrator can select one transmission mode and audio bit rate.
  • Page 114 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 In the Half-duplex mode, the local/remote site can only talk or listen to the other site at a time.  Simplex (Talk only) In the Talk only Simplex mode, the local/remote site can only talk to the other site.
  • Page 115 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The figure below is the camera configuration page. Details of each parameter setting are described in the following subsections. NOTE: Please note that the function buttons will vary depending on the camera model.
  • Page 116 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Exposure pull-down menu is shown as follows: The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening, the amount of exposure by the sensor (shutter speed) and other exposure parameters.
  • Page 117 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Fixed Shutter Mode In this mode, fixed shutter speed could be selected from the dropdown menu. The shutter speed range is from 1/10000 to1 (1/1.5) sec. with 19 (18) options. Users could select suitable shutter speed according to the environmental illuminance.
  • Page 118 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Manual Mode In this mode, users can change the White Balance value manually. Users can select a number between 0 ~127 of “Rgain/ Bgain” item to gain the red/ blue illuminant on the Live Video Pane. Press < √ > to confirm the new setting.
  • Page 119 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Camera image saturation level is adjustable; please select ranging from -6 to +19. Press < √ > to confirm the new setting.
  • Page 120 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Camera image hue level is adjustable; please select ranging from -12 to +13. Press < √ > to confirm the new setting. Auto/On/Off Mode With the IR cut filter, the Dome Camera can still catch clear image at night time or in low light conditions.
  • Page 121 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 confirm the new setting.
  • Page 122 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Press the tab “Logout” in the top of the page, and the login window will pop up. This enables login with another user name.
  • Page 123 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The IP Camera bundles Central Management System (CMS) software. Offering powerful functionalities via intuitive interface, it is a centralized monitoring solution of your video surveillance equipments. It gives the user access to monitor multiple IP Cameras and Digital Video Recorders (DVRs), and allows the user to simultaneously monitor 16 sites per group (up to 10 groups) within several clicks.
  • Page 124 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Camera Full HD Real-time Full HD Image Sensor 1/2.5” Progressive CMOS Effective Pixels 1920(H) x 1080(V) Color 0.2 lux @ F1.4 0.2 lux @ F1.4 Minimum Illumination 0.02 lux @ F1.4 0.02 lux @ F1.4 Shutter Speed 1~ 1/10000 sec.
  • Page 125 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Two-way Line out, Line in/ mic in Audio Audio Compression G.711/G.726 5V 10kΩ pull up Input Alarm Output Photo Relay Output 300V DC/AC Event Notification HTTP, FTP, SMTP English, French, German, Italian, Korean, Simplified Multiple Languages Chinese, Russian, Korean Network...
  • Page 126 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 ∅ 170 x 210 mm (∅ 6.7 x 8.3 inches) Outdoor Indoor 0.8 kg (1.8 lbs) Weight Outdoor 1.3 kg (2.9 lbs)
  • Page 127 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 If ActiveX control installation is blocked, please either set Internet security level to default or change ActiveX controls and plug-ins settings. Internet Security Level: Default Step 1: Start the Internet Explorer (IE). Step 2: Select <Tools>...
  • Page 128 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 129 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 4: Down the page, press “Default Level” (see the figure above) and click “OK” to confirm the setting. Close the browser window, and open a new one later when accessing the IP Camera. ActiveX Controls and Plug-ins Settings Step 1~3: Refer to the previous section above.
  • Page 130 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The Security Settings screen is displayed as below: Step 5: Under “ActiveX controls and plug-ins”, set ALL items (as listed below) to <Enable> or <Prompt>. Please note that the items vary by IE version.
  • Page 131 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 scripting 9. Run ActiveX controls and plug-ins Script ActiveX controls marked safe for scripting Step 6: Click <OK> to accept the settings and close the <Security> screen. Step 7: Click <OK> to close the Internet Options screen. Step 8: Close the browser window, and restart a new one later for accessing the IP Camera.
  • Page 132 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 The procedure of DC Viewer software download is specified as follows. Step 1: In the DC Viewer installation page, click “Next” for starting installing. Step 2: Setup starts. Please wait for a while until the loading bar runs out.
  • Page 133 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 3: Click “Finish” to close the DC Viewer installation page.
  • Page 134 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Then, the IP Camera’s Home page will display as follows:...
  • Page 135 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Please follow the instructions below to install UPnP components. Step 1: Go to “Start”, click on “Control Panel”, and then double click “Add or Remove Programs”. Step 2: Click on “Add/Remove Windows Components” in the Add or Remove Programs page.
  • Page 136 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 3: Select “Networking Services” from the Components list in the Components Wizard window, and then click “Details”. Windows Step 4: Select “UPnP User Interface” in the Networking Services’...
  • Page 137 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 subcomponents list and then click “OK”.
  • Page 138 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Step 5: Click “Next” in the Windows Components Wizard page. Step 6: Click “Finish” to complete installation.
  • Page 139 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0...
  • Page 140 All other company or product names mentioned are used for identification purposes only and may be trademarks of their respective owners. Manufacturer: ALLNET GmbH ALLNET Deutschland GmbH Maistrasse 2 82110 Germering Tel. +49 89 894 222 22 Fax +49 89 894 222 33 email: info@allnet.de...
  • Page 141 Full HD Vandal Proof IP Outdoor Dome Camera Version 1.0 Hersteller / ALLNET GmbH Manufacturer: Produkt / Product: ALL2295 Typ / Type: Full HD Real-time Vandal Proof IP Dome Camera Report No. : E081901 The equipment beyond was tested by Global Certification Corp. for compliance with the requirements set forth in the European Council Directive 2004/108/EC and the technical standards mentioned above.