Flt. C (Flight Conditions Or "Idle-Up's"); Acro Data Sheet - ACE RC sky tech TS6i+ Instruction Manual

SWAH (120 Swash Plate Programming)
4. Call up the swash screen by repeatedly pressing one of the Up Down EDIT buttons until the SWAH
window appears.
The function is automatically active when you select 120 mixing in the model setup menu.
5. If all the servos raise the swash with increasing collective, go to the next step. If they lower the
swash, press the CURSOR Right button twice to get to the collective setting menu
(the arrow appears over the number 6).
Now press the DATA "-" button until the sign is reversed in front of the percentage value.
Now the swash should properly respond to collective.
If you've done the wrong thing, you can reset the percentage by pressing the Active/Inhibit (Clear) button.
6. If all the servos tilt the swash to the right with right aileron stick, go to the next step.
If they tilt the swash to the left, press the CURSOR Right button once to get to the aileron setting menu (the arrow appears over the number 1).
Reverse the sign in front of the percentage with the DATA "-" button. Now the swash should properly respond to aileron.
7. If all the servos tilt the swash aft with up elevator stick, go to the next step.
If they tilt the swash forwards, press the CURSOR Right button once to get to the elevator setting menu (the arrow appears over the number 2).
Now press the DATA "-" button until the sign is reversed in front of the percentage value.
Now the swash should properly respond to elevator.
8. Double check that all three functions, collective, aileron, and elevator, produce the desired result on the swashplate.
Do not set any SWAH values to 0% or you will disable the response to that control!

FLT. C (Flight Conditions or "Idle-Up's")

FLT. C (Flight Conditions or "Idle-Up's")
+
Your Sky Tech TS6i 's system's HELI menu provides three flight modes in addition to the normal one (NOR). Within each condition,
you may program an independent set of dual rates, exponentials, throttle and pitch curves, revolution mixing, and gyro gain.
In the HELI menus, these are automatically called up whenever you switch to a new condition.
NOR is intended for hovering flight. ST1 may be used for forward flight and mild aerobatics, ST2 may be used for inverted, and ST3 is used
for autorotations as it includes a throttle hold feature which disengages the throttle servo from collective commands.
These conditions are activated whenever the model memory is chosen to be HELI type
The defaults for the switches controlling these flight conditions are as follows:
- NOR: ON when Flt. Mode (SW-3) Switch is BACK.
- ST1: ON when Flt. Mode (SW-3) Switch CENTER.
- ST2: ON when Flt. Mode (SW-4) Switch is FORWARD
- ST3: ON when SW-1 is DOWN. (For Throttle Hold only)
As these functions are switched on or off, ST3 = HOLD has
highest priority, followed by ST2 and ST1. Regular settings
(NOR)occur when all of the others are off.
Throttle and pitch curves, revolution mixing, and gyro gain may be
independently selected for each condition.
Here are some suggested starting settings if your instructions do
not provide any:
Page 51
Throttle Curve ST1
Point 1 (low) 2 3 4 5 (high)
% 20 38 50 75 100
Throttle Curve ST2
Point 1 (low) 2 3 4 5 (high)
% 100 50 38 50 100
Pitch Curve ST1
Point 1 (low) 2 3 4 5 (high)
Pitch -4 deg. +0.5 +6.0 +7.5 +9.0
Pitch Curve ST2
Point 1 (low) 2 3 4 5 (high)
Pitch -9 deg. -6.0 0 6.0 9 or 10.0
Pitch Curve ST3 (HOLD)
Point 1 (low) 2 3 4 5 (high)
Pitch - 4 deg. -- + 6.5 -- +12
+
Sky Tech TS6i

ACRO DATA SHEET

MODEL TYPE : ACRO SFT : N , P
MODEL NAME : 0 1 2 3 4 5 6 7
CH1 CH2
L/U % L/U % L/U
EPA
R/D % R/D % R/D
0 % %
D/R
1 % %
0 % %
EXP
1 % %
S.TRM
% %
S.REV
NOR , REV NOR , REV
ON MAS
% %
INH SLV
% %
PMX
TRM ON
OFF
AILE AILE
ON STICK
%
ELVN
CH1 CH2
INH SERVO
AILE AILE
ON STICK
%
FLPN
CH1 CH6
INH SERVO
ELEV ELEV
ON STICK
V.TAL %
SERVO CH2 CH4
INH
ON
A → R
%
INH
ON
E → F
%
INH
CUT
NOR % %
% %
ST1
CAMB
% %
ST2
% %
ST3
NOR ON
ST1 ON , OFF
FLT.C
ST2 ON , OFF
ST3 ON , OFF
TIMER
MODE 1 , 2
*Each flight condition for D/R & EXP are not shown on the chart.
8 9 .
CH3 CH4 CH5 CH6
% L/U % L/U % L/U
% R/D % R/D % R/D
%
%
%
%
% % %
NOR , REV NOR , REV NOR , REV NOR , REV
% % %
% % %
ELEV ELEV
% %
CH2 CH1
FLAP FLAP
% %
CH6 CH1
RUDD RUDD
% %
CH4 CH2
%
*Please make a copy and fill this form out.
Page 52
%
%
%
%
%
%
%
%
%
%
%
%