Do you have a question about the RCS36 and is the answer not in the manual?
Questions and answers
Jan Olsen
April 8, 2025
I cannot find anywherein the manual about a safety switch that turns off the machine. The machine will not start.
1 comments:
Mr. Anderson
April 9, 2025
Yes, the Ryobi RCS36 has a safety switch. To start the device, you must first press a safety lock button and then the trigger switch. This prevents accidental starting.
This answer is automatically generated
Jan Olsen
April 8, 2025
Is there a safety switch on the Ryobi RCS36? my RCS36 will not start.
1 comments:
Mr. Anderson
April 9, 2025
Yes, the Ryobi RCS36 has a safety switch called a safety lock-off button. It won't start if the safety lock-off button is not pressed while pulling the switch trigger.
Page 1
RCS36/RCS36B 36V CORDLESS CHAIN SAW OPERATOR’S MANUAL (Original Instructions) Important! It is essential you read the instructions in this manual before starting and operating this machine.
Ryobi’s high standard for dependability, ease of operation, atmospheres, such as in the presence of flammable and operator safety. When properly cared for, it will give liquids, gases or dust. Power tools create sparks you years of rugged, trouble-free performance.
English (Original Instructions) Do not use the power tool if the switch does not SERVICE turn it on and off. Any power tool that cannot be Have your power tool serviced by a qualified repair controlled with the switch is dangerous and must be person using only identical replacement parts.
English (Original Instructions) moving saw chain. ADDITIONAL WARNINGS Follow instructions for lubricating, chain tensioning It has been reported that vibrations from hand-held and changing accessories. Improperly tensioned tools may contribute to a condition called Raynaud’s or lubricated chain may either break or increase the Syndrome in certain individuals.
Page 6
English (Original Instructions) SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL DESIGNATION/EXPLANATION Voltage Watt - Power Direct current - Type or characteristic of current Precautions that involve your safety.
Chain stop < 2s You can purchase bar and chain replacements from your Chain oil tank Ryobi local dealer. 110 ml capacity RCS36 bar replacement: RAC226 (Tri-link M1431245- 4.4 kg 3.03 kg 1041HL) Weight (with battery) (without battery) RCS36 chain replacement: RAC227(Tri-link CL14345PB) Emission sound 81.2 dB(A)
After the run-in time, check the chain tension and re- tighten the chain if necessary. Check the chain tension before each use of the saw. OPERATION For complete charging instructions, refer to the Operator’s Manuals for your Ryobi battery pack and...
English (Original Instructions) any utility line, the utility company should be notified WARNING immediately. Never operate the chain saw without sufficient chain The chain saw operator should keep on the uphill side of lubrication as this might damage the saw and is a threat the terrain as the tree is likely to roll or slide downhill after to safety.
English (Original Instructions) Bucking is cutting a log into lengths. It is important to adjustments to the chain. make sure your footing is firm and your weight is evenly Make sure that you have the correct replacement distributed on both feet. When possible, the log should be bar and chain as advised earlier in the specification raised and supported by the use of limbs, logs or chocks.
Authorised Service Centre. For your with electric sharpener. nearest Ryobi Authorised Service Centre call 1300 361 505 or visit the website www.ryobi.com.au GUIDE BAR MAINTENANCE When you have finished working, clean out the groove STORAGE and the oil passages with a scraping hook.
Page 12
Subject to the guarantee condition below, this Ryobi guarantee does not cover damage, malfunction or tool (hereinafter called “the product”) is guaranteed by failure resulting from misuse, neglect, abuse, or used TECHTRONIC INDUSTRIES AUSTRALIA for a purpose for which it was not designed or is not LIMITED (hereinafter called “the Company”) to be free...
Need help?
Do you have a question about the RCS36 and is the answer not in the manual?
Questions and answers
I cannot find anywherein the manual about a safety switch that turns off the machine. The machine will not start.
Yes, the Ryobi RCS36 has a safety switch. To start the device, you must first press a safety lock button and then the trigger switch. This prevents accidental starting.
This answer is automatically generated
Is there a safety switch on the Ryobi RCS36? my RCS36 will not start.
Yes, the Ryobi RCS36 has a safety switch called a safety lock-off button. It won't start if the safety lock-off button is not pressed while pulling the switch trigger.
This answer is automatically generated