Advertisement
e-DATA MEMORY Records
Each e-DATA MEMORY record can contain up to 95 characters. Records are
stored in memory in the sequence they are created.
• Before you can input, recall, edit or delete an e-DATA MEMORY record, you
must first access the data by entering the e-DATA MEMORY Mode.
• The number of records you can store in e-DATA MEMORY depends on the
number of characters that make up each record. See "e-DATA MEMORY
Management" for more information.
To create a new e-DATA MEMORY record
1. While an e-DATA MEMORY record screen is on the
display, press B and D at the same time to
display the remaining memory screen.
• You do not have to perform the above step if the
remaining memory screen is already on the
display.
• If
is shown for remaining memory, it means
that memory is full. To store another record, you
will first have to delete some of the records stored
Remaining memory
in memory.
2. Hold down A until the flashing cursor ( ) appears
Record number
on the display, which indicates the setting screen.
3. Use D and B to change the character at the
cursor position. The character changes in the
sequence shown below.
Press
.
to
(space)
(lower-case)
to
(number)
• See the "Character List" at the back of this manual for information about
the characters you can input.
4. When the character you want is at the cursor position, press C to move the
cursor to the right.
5. Repeat steps 3 and 4 until the text is complete.
• If memory becomes full while you are inputting text, the cursor will jump to
the first (leftmost) character of the text when you press C, instead of
advancing to the right.
6. Press A to store your data and return to the e-DATA MEMORY record
screen (without the cursor).
• The message
appears for about one second, followed by an e-DATA
MEMORY record screen, which shows the text you just input in the lower part
of the display, and a record number automatically assigned by the watch in
the upper part of the display.
• While the record number is in the upper part of the display, you can see only
four characters of the text in the record. You can scroll through the text on the
screen by pressing the B button. See "To recall e-DATA MEMORY records"
for more information.
To recall e-DATA MEMORY records
1. While an e-DATA MEMORY record screen or the remaining memory screen
is on the display, press D to scroll forward through e-DATA MEMORY
records.
• Each press of D advances to the next record and shows its record
number and first four characters of its text.
2. Press B to display the next four characters of text.
Record
number
Press D to display the next record.
(Red on black)
First 4
Each press of B scrolls forward four characters.
characters
• Pressing D while the last record in memory is on the display changes to the
remaining memory screen. Pressing D again displays the first record.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode display the record you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Press C to move the flashing to the character you want to change.
4. Use D and B to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, display the record you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message
appears to indicate that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for
input.
4. Input data or press A to return to the e-DATA MEMORY record screen.
USER'S GUIDE 2465
Press
.
to
(symbol)
to
(upper-case)
Second 4
characters
Alarm
You can select a standard Daily Alarm that sounds
AM indicator
only once each day, or a snooze alarm that repeats
up to seven times, every five minutes.
You can also turn on an Hourly Time Signal that
causes the watch to beep twice every hour on the
hour.
• Pressing D in the Alarm Mode toggles between
the alarm screen (
screen (
• Alarm settings (and Hourly Time Signal settings)
are available in the Alarm Mode, which you enter by
pressing C.
Alarm time
(Hour : Minutes)
To set an alarm time
1. In the Alarm Mode, press D to display the alarm
screen.
2. Hold down A until the hour setting of the alarm
time starts to flash, which indicates the setting
screen.
• This operation automatically turns on the normal
alarm.
3. Press C to move the flashing between the hour
and minute settings.
4. While a setting is flashing, press D to increase it.
• When setting the alarm time using the 12-hour
format, take care to set the time correctly as a.m.
(A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
Starting from the point the Timekeeping Mode time reaches one hour before an
alarm time the display pattern changes each second. This pre-alarm feature
lets you know that an alarm time is about to be reached.
When the actual alarm time is reached, an alarm tone sounds for 10 seconds.
In the case of the snooze alarm, the alarm repeats up to seven times every five
minutes.
• Pressing any button stops the pre-alarm operation or the alarm tone
operation.
• The pre-alarm feature works in the Timekeeping Mode only.
Stopping a Snooze Alarm Operation
After a snooze alarm time is reached, you can perform the following steps
during any 5-minute interval between alarms to stop the snooze alarm
operation.
To stop a snooze alarm operation
1. While in the Alarm Mode, press D to display the alarm screen.
2. Next, press A to turn off the alarm or to select the normal alarm.
• Note that this also changes the alarm type setting. If you want to use the
snooze alarm again, you must re-select it as the alarm type. See "To select
the Daily Alarm type" for more information.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To select the Daily Alarm type
1. In the Alarm Mode, press D to display the alarm screen.
2. Press A to cycle through the available Daily Alarm settings shown below.
Normal alarm on
Snooze alarm on
Red on black
Alarm on indicator
Snooze alarm on indicator
(White on red)
(White on red)
• The alarm on indicator and the snooze alarm on indicator are shown on the
display in all modes while these functions are turned on.
• The snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
• Displaying the Alarm Mode setting screen automatically changes the alarm
type to normal alarm.
• Displaying the Timekeeping Mode setting screen during a 5-minute interval
between snooze alarms stops the current snooze alarm operation (but
snooze alarm remains as the alarm type setting).
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, press D to display the Hourly Time Signal screen.
2. Press A to turn it on and off.
On
Red on black
Hourly time signal on indicator
(White on red)
• The Hourly Time Signal on indicator is shown on the display in all modes
while this function is turned on.
) and the hourly time signal
).
Alarm off
Blue on white
Off
Blue on white
2
Advertisement
