Mytee Grand Prix HP100 Instruction Manual & Safety Manual

29
F
31
28
To filter in sol tank 30
thru B186 (#65)
21
20 27
19 32
33
22
E
23
16
17 18
To female q.d. 38
24
thru B109 (#9)
37 34
26
1 36
10
To sol tank 25
thru B103 (#9) 35
11 15
To inlet on base
(#50)
12
7 9
8
6
5
13
D
42
9
45
43
14
4
44
9
3
2
1
55
54
C
46
47
51
36
50
24
B
48
49
A
8 7 6
8 7 6
ITEM NO. PART NO. DESCRIPTION QTY. ITEM NO. PART NO.
1 H273 nut, kep, #10-32 zinc 6 51 G001
2 H230 screw, 10-32 x 1/2 phil pan 2 52 H219
3 H528 bracket, heater mounting, dual 1 53 H239
4 E571 heating rod, 600W, 115V 2 54 H224
F 5 H274 screw, #6 x 3/16, phil pan head, self-tapping 10 55 H254
6 E574 Thermostat, 310°F ± 10°F, Manual, 1/4" 2 56 G061
7 E573 Thermostat, 200°, Auto, 1/4" 2 57 P757
8 H903A heater, aluminum cast, single w/wrap & drilled holes 2
58 H215
9 B103 elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 6 59 H213
10 AH108S sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi 1 60 H211
11 AH120 sol hose, 28" x 1/4", 1/4 fpt solid x 1/4 fpt swivel, neptune 1 61 G052
12 B124 valve, brass, relief, 175 psi 1 62 H204
13 B113 tee, brass, 1/4" fpt 1 63 H378
14 AH156 hose, 3/8" x 6", (OAL), f x fsw, surge, 1600psi 1 64 H201
15 AH103 hose, 3/8" x 10", (OAL), f x fsw, surge, 1600psi 1 65 B186 elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
16 B207 elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt 1
E 66 H299
17 B108 valve, brass, 1/4" check 1 67 B216
18 B172 elbow, brass, 90 deg, 1/2" barb x 3/8"mpt 1 68 B210
19 PH615 sol hose, 1/2" kuri 100psi 1 69 B119A
20 H347 clamp, hose, 5/16-29/32 2 70 H212
21 B160 adapter, brass, 1/2" barb x 3/8" fsw, ball end 1 71 B111 adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
22 C305 pump, 100psi, demand, 115V 1 72 B107
23 H222 screw, #10-32 x 1-1/4" phil pan head, zinc 4 73 AH105 hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi
24 H210 washer, 1/4" flat, s/s 16 74 H413 washer, nylon, 9/16id x 1-1/16od x .031
25 B136 elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt 1 75 B106
26 B105 bushing, brass, 3/8"mpt x 1/4" 1 76 B102
27 H217 clamp, hose, 2-1/4 DIA 3 77 H912
D
28 PH627 vac hose, 1-1/2", wire reinforced 1 78 H922
29 H300 cuff, black 1.5" 1 79 PH633-11
30 H770 bolt, 1/4-20 x 1/2" serrated hex flange, zinc 9
80 P755
31 C302 vac motor, 3 stage, 115V, tangential 1 81 H235
32 G004 gasket, vacuum motor 1 82 H304
33 H501 vac support, 3 stage, 4-1/16" 3 83 G090
34 H201 bolt, 1/4-20 x 1/2" hex head, zinc 3 84 G091
35 H768 bolt, 1/4-20 x 3/4" serrated hex flange, zinc 3 85 A925
36 H216 nut, lock, 1/4-20, nylon insert 13 86 P758
37 P735 manifold, single vac 1 87 H326
38 H330 plate, single manifold, 6.5" x 9" 1 88 E515
39 PH628 vac hose, 2", wire reinforced 1 89 H246
C 40 PH633-03 pipe, pvc, 1-1/2" 1 90 H390A
41 H244 adapter, pvc, 1-1/2" fms x fmpt 2 91 H225
42 E531 power cord, end, 25', 12/3 yel 1 92 H226
43 H220 fitting, strain relief, cord 1
44 H221 nut, lock, 1/2" steel 1
ITEMS NOT SHOWN:
45 P756 base, firebird 1
46 H343 screw, #10 x 5/8" hex head, zinc 8
47 H296 guard, cooling fan, wire 2
48 H203 bolt, 1/4-20 x 1-1/4" hex head 10
49 H667 caster, 3" 2
50 H229 fitting, inlet, pvc, 1-1/2", gray 3
B
A
27
39
80
56 81
27
40
79
41
50
61 41
48
60
60
58 61
59 86
57
87
88
89
77
53
30
70
74 9
75 59
73
52 78
62
50
74
24 71
36 70
63 76
24 59
64
72
70
66
70
67
65
66
9
66
66
69
To heater "OUT"
68
thru AH108S (#10)
To pump "IN"
thru B160 (#21)
70
9
70
71
Inside sol tank
To relief valve
thru AH120 (#11)
5 4 3 2
5 4 3
DESCRIPTION QTY.
gasket, inlet, 1.80" i.d. 2
cap, axle, 1/2" 2
wheel, 8" 2
axle, 1/2" x 17-3/4", fb 1
washer, axle, cut 1/2" id 4
cover, sol tank, fb 1
sol tank, firebird 1
nut, hex, 1/4-20 s/s 2
washer, 1/4" lock, s/s 6
washer, 1/4"id x 1"od, flat, s/s 4
washer, buna 1-1/8" od x 3/16" id 4
bolt, 1/4-20 x 1-3/4" hex head, s/s 2
bracket, front hinge, sp/fb 1
bolt, 1/4-20 x 1/2" hex head, zinc 2
1
washer, 11/16"id x 1-1/2"od x .075, s/s 4
nipple, brass, 3/8" x close 1
bushing, brass, 1/2"mpt x 3/8" fpt, hex 1
filter, strainer, 1/2" 1
washer, 9/16"id x 1"od, flat, s/s 6
2
nipple, brass, 1/4"m, hex 1
1
2
nipple, brass, 1/4" x close 1
qd, brass, 1/4" f 1
bracket, rear, fb/spy 1
knob, thumb screw, for bracket 2
pipe, pvc, 1-1/2" 1
elbow, U, 180, 1-1/2", float 1
cage, float, standard 1
screw, #8 x 5/8 phil oval, s/s 6
lid, vac tank, black, 7" 1
gasket, 7", vac lid 1
elbow, inlet assy 1-1/2" 1
vac tank, firebird 1
plate, switch, 3 hole, fb 1
switch, rocker, 2 position 3
screw, #8-32 x 3/8" SHCS, alloy 4
bracket, "L" (all extracters) 2
valve, drain, 1-1/2" 1
spout, drain, 45 degree 1
UNPACKING THE MACHINE
Before unpacking the machine, inspect all boxes and pallets for signs of shipping damage. Please be
F
aware that all packages leave Mytee Products in perfect condition. Any equipment or carton damage
caused during shipping is the responsibility of the freight company, and should be handled by filing a
claim with the carrier.
82
83
H226 -
E
84 45 Drain Elbow
O
H375 - Hose Hanger
85
A919 - Exterior
51
Blower Attachment
D The safety labels
appear on the
machine in the
locations indicated.
91
Replace labels if they
92
become damaged or
cannot be read.
MACHINE COMPONENTS
Vacuum
C
Tank Lid
Solution
Tank
30
Motor
90
Housing/
Base
30
B
3" Upholstery Tool
Blower Attachment
NAME DATE mytee PRODUCTS, INC.
A PRE-OPERATION
V. LaBarbera
DRAWN 11/1/07 858-679-1191
CHECKED TITLE:
1. Vacuum carpet and upholstery and remove
other debris.
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. REV
DRAWING IS THE SOLE PROPERTY OF HP100 2. Perform MACHINE SETUP procedures.
MYTEE PRODUCTS, INC. ANY D
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED. 3. Inspect power cord for damage.
SCALE: 1:5 DO NOT SCALE SHEET 2 OF 2
DRAWING
1
2 1
REVISIONS
Mytee Products, Inc. endeavors to provide high quality products and product support to its customers and therefore backs up
REV. DESCRIPTION DATE APPROVED
ll of its new products purchased from Mytee Products Inc. ("Mytee") or any authorized Mytee distributor/service center
a
OD ORIGINAL DRAFT JFL
with this limited warranty. This limited warranty begins on the date of the customer's purchase and is valid and avail-
able to the original purchaser only. Mytee's products are for commercial use only and are not intended for personal,
family or household uses.
F
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIP-
TION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT,
OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE PROPER
USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE'S GOODS. THIS LIMITED
WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE
.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for 90 days from the date of original pur-
E
chase. "Wear parts" are items which wear out as a result of usage or the passage of time and are consumed despite
attempts to maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses, switches, ther-
mostats, plastisol parts, filters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts
deemed wear items in Mytee's sole discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.
PUMP, VACUUM MOTOR AND HEATER 1-YEAR LIMITED WARRANTY: Mytee warrants that pumps, vacuum and floor
machine motors, and heaters will be free from manufacturing defects, defects in workmanship, and defects in material
for one (1) year from the date of original purchase. This warranty does not apply and is void if the pump, vacuum motor,
or heater has worn brush motors, water damage, chemical build-up, chemical damage, or evidence of abuse, neglect or
tampering. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs.
D
HOUSING 5-YEAR LIMITED WARRANTY: For five (5) years from the date of purchase, Mytee warrants a percentage of the
cost of replacement of rotationally-molded housings pro-rated as follows: Mytee will pay 100% of replacement cost in
the first year from the date of purchase, 75% of replacement cost in the second year from the date of purchase, 50% in
the third year, 25% in the fourth year, and 12% in the fifth year. Replacement cost does not include the cost of shipping
or labor.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE
EXCLUSIVE REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO EVENT
SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY DAMAGES, OR PER-
SONAL INJURIES.
C
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication,
improper installation, abuse, lack of maintenance, negligence in use or care, abnormal use, alteration of design, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone
other than Mytee or a Mytee authorized distributor or service center.
Mytee may make changes in products it manufactures and markets at any time; these changes are made without obliga-
tion to change, retrofit, or upgrade any product previously sold or manufactured. Mytee has no obligation to honor the
limited warranties set forth herein unless the original purchaser, promptly upon discovering the warranty claim and
prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service center to describe
the claim and to receive and follow instructions for documenting and resolving the claim. In addition, the purchaser
B
must provide the product to which the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection.
If any provision or portion of this limited warranty policy is found to be unenforceable, then the remaining provisions
and portions shall remain valid and enforceable. If any provision or portion of this limited warranty policy is found to
be limited by law, then that provision or portion shall be construed to make it effective within the bounds of law. For ex-
ample, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have
the minimum duration required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made
herein shall be construed to apply to the fullest extent possible without violating the law.
NAME DATE mytee PRODUCTS, INC. A
The validity, construction and performance of this warranty policy shall be governed by the laws of the State of Califor-
DRAWN V. LaBarbera 11/1/07 858-679-1191
TITLE:
CHECKED nia, without respect to conflicts of laws principles. The exclusive jurisdiction of any legal action arising from or related
to this warranty policy shall be in the State of California and no legal action shall be commenced elsewhere.
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
SIZE DWG. NO. REV
DRAWING IS THE SOLE PROPERTY OF HP100
MYTEE PRODUCTS, INC. ANY D
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
SCALE: 1:3 DO NOT SCALE SHEET 1 OF 2
DRAWING
Grand Prix HP100
7. Turning machine on.
A. Turn pump switch on.
B. Pull up on tool lever to release air in the line.
Hold lever until you have a steady flow of water
coming out of the wand.
C. Once pump is primed and you have pressure
in the solution line, turn on heater switch(s) (if
model is equipped with heater) and wait a few
minutes for water to heat up.
D. Once water is heated, turn on vacuum
motors and begin cleaning.
H294 - 25' Blower Hose
8501 - 15' 1-1/4" Vac/Sol Hose
NOTE: When cleaning upholstery, always check
manufacturer's cleaning instructions.
PC88 -
Interior
Blower 8400 - 3" Stainless
1. Work away from outlet and power cord to prevent cord
Attachment Steel Upholstery Tool
damage.
SAFETY LABELS
2. Use a recommended foam control solution in the
recovery tank to prevent vacuum motor damage.
!
WARNING: Flammable materials can cause an Periodically check for excessive foam buildup in solution
explosion or fire. Do not use flammable materials in
tank, and recovery tank.
tank(s). Flammable materials or reactive metals can
3. To clean heavily soiled areas, repeat cleaning path from
cause explosion or fire.
different direction.
!
WARNING LABEL- Located on back. Label warns
4. When ball float shuts off vacuum, it is time to empty the
operator of safe practices of equipment.
dirty water from the recovery tank, and refill solution tank.
SETUP
5. After cleaning, relieve water pressure from tool before
disconnecting hose. Squeeze trigger for five seconds
1. Open lid of solution tank. Fill solution tank with
after turning main power switch off.
water or approved cleaning agent.
Vacuum ! WARNING: Flammable materials can cause an
Hose explosion or fire. Do not use flammable solutions or FOR SAFETY: When servicing machine, unplug cord from
Connector materials in tank(s).
wall outlet.
1. Turn machine off and unplug power cord.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
2. Remove solution & vacuum hose.
Hose
Hanger 3.Attach 45º-drain elbow to dump valve and lift up drain
ATTENTION: If using powdered cleaning chemicals,
valve lever to empty recovery tank.
mix prior to adding.
DRAINING RECOVERY TANK
Solution
2. Attach solution hose. (Located front of machine.)
Hose NOTE: Make sure the quick disconnects snap MACHINE MAINTENENCE
Connector together firmly. As you do this, always inspect
To keep machine in good working condition, simply follow
hoses for cracks or fraying. Do not use if hoses are
machine's daily and weekly maintenance procedures.
Vac/Sol Hose damaged.
Check valves and relief valves should be replaced
annually.
3. Attach other end of solution hose to wand.
FOR SAFETY: When servicing machine, unplug cord from
4. Attach vacuum hose to recovery tank. wall outlet.
DAILY MAINTENANCE
5. Plug machine's cord into a grounded wall outlet.
FOR SAFETY: Do not operate machine unless cord is 1. Empty and rinse out solution tank thoroughly.
properly grounded.
2. Wipe off power cord and check for damage, replace if
necessary. Coil cord neatly after use.
FOR SAFETY: Do not operate machine with the use
of an extension cord.
3. Clean machine with an all purpose cleaner and damp cloth.
WARRANTY
OPERATION
WEEKLY MAINTENANCE
(EVERY 20 HOURS OF OPERATION)
1. Flush solution system with Mytee system
maintainer to dissolve normal chemical buildup.
a. Pour 7.5L (2 gal) of hot water 60°C
(140°F) into solution tank. Add Mytee
system maintainer according to mixing
instructions on bottle
FOR SAFETY: When using machine, follow
mixing and handling instructions on chemical
containers.
b. Operate machine for one minute.
c. Shut off machine and allow remaining
solution to break down chemical buildup
TIPS overnight.
d. Next day, spray out remaining
solution and flush system with 11L (3gal)
of clean water.
2. Inspect vacuum hoses for holes and loose
cuffs. Drain and dry the vacuum hose as well.
3. Inspect spray pattern for clogging. If
clogged, remove spray tips and soak them in
a recommended liquid neutralizer for up to six
hours. To remove spray tip, twist spray tip body
counter-clockwise.
4. Lubricate wheels with water resistant oil.
5. Inspect machine for water leaks and loose
hardware.
MAINTENANCE
6. Remove float shut-off screen from recovery
tank and clean.
NOTE: The float shut off screen is not glued on.
Simply pull it off.
STORING MACHINE
1. Before storing machine, be certain to
completely drain and rinse tanks of all water and
solution.
2. Drain and dry the vacuum hose as well, using
the drain hose provided
3. Store machine in a dry area in the upright
position.
4. Open recovery tank cover to promote air
circulation
ATTENTION: Do not expose to rain. Store indoors.
ATTENTION: If storing machine in freezing
temperatures, be sure that machine and solution
system are completely drained and dry.
grand prix ™
hp100
Instruction Manual
& Safety Guide