Hand Held Products 4620 Quick Start Manual
  1. Manuals
  2. Brands
  3. Hand Held Products Manuals
  4. Barcode Reader
  5. IMAGETEAM 4620
  6. Quick start manual

Hand Held Products 4620 Quick Start Manual

Hide thumbs Also See for 4620:
Table of Contents

Advertisement

Quick Links

Download this manual See also: System Manual
4620, 5620

Quick Start

Advertisement

Table of Contents
loading

Related Manuals for Hand Held Products 4620

Summary of Contents for Hand Held Products 4620

  • Page 1: Quick Start

    4620, 5620 Quick Start...

  • Page 2: Usb Connection

    Getting Started Turn off power before connecting the base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the imager in the base to establish a link. The green LED on the base flashes to indicate the imager’s battery is charging.
  • Page 3 Keyboard Wedge Connection Serial (RS-232) Connection...

  • Page 4: Factory Defaults

    Reading Techniques The view finder projects an aiming beam that should be centered over the bar code, but can be positioned in any direction for a good read. Hold the imager over the bar code, pull the trigger, and center the aiming beam on the bar code. The aiming beam is smaller when the imager is closer to the code and larger when it is farther from the code.
  • Page 5 PC Interface Scan the bar code that describes the PC or interface you are using. USB Keyboard (PC) RS-232 Japan DOS/V AT/PS2 Keyboard Wedge (Default) Emulate External Keyboard...

  • Page 6: Keyboard Country

    Keyboard Country Scan the Program Keyboard Country bar code below, then scan the numeric bar code(s) from page 11, then the Save bar code to program the keyboard for your country. As a general rule, the following characters are not supported by the imager for countries other than the United States: @ | $ # { } [ ] = / ‘...
  • Page 7 Open Link Scan the Open Link bar code, then place the imager into the base to establish a link. Placing a different imager into the base establishes a new link and the old imager is unlinked. Open Link Override Locked Imager If you need to replace a broken or lost imager that is linked to a base, scan the Override Locked Imager bar code with a new imager, and place that...

  • Page 8: Unlinking The Imager

    Unlinking the Imager If the base has an imager linked to it, that imager must be unlinked before a new imager can be linked. Once the previous imager is unlinked, it will no longer communicate with the base. Scan the Unlink Imager bar code to unlink an imager.

  • Page 9: Reread Delay

    Reread Delay This sets the time period before the imager can read the same bar code a second time. Setting a reread delay protects against accidental rereads of the same bar code. Medium Reread Delay Suffix If you want a carriage return after the bar code, scan the Add CR Suffix bar code.

  • Page 10: Function Code Transmit

    Add Code ID Prefix to all Symbologies Scan the following bar code if you wish to add a Code ID prefix to all symbologies at once. Add Code ID Prefix to all Symbologies Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the imager transmits the function code to the terminal.
  • Page 11 Data Format Editor Instructions The following are abbreviated instructions for entering a data format. For complete instructions refer to your User’s Guide, available at our website, www.handheld.com. 1. Scan the Enter Data Format symbol. 2. Primary/Alternate Format: scan 0 for Primary Format 3.
  • Page 12 Programming Chart...
  • Page 13 Save...
  • Page 14 User’s Guide. Visual Menu Technical Assistance If you need assistance installing or troubleshooting your imager, please call your Distributor or the nearest Hand Held Products technical support office: North America/Canada: Telephone: (800) 782-4263, option 4 (8 a.m. to 6 p.m. EST)

  • Page 15: Online Technical Assistance

    To download the full User’s Guide for these products, visit our website at www.handheld.com Product Service and Repair Hand Held Products provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, return the unit to Hand Held Products (postage paid) with a copy of the dated purchase record attached.
  • Page 16 North America Hand Held Products Corporate Offices Telephone: (800) 782-4263, Option 3 Fax: (704) 566-6015 naservice@handheld.com E-mail: America Latina Hand Held Products America Latina Teléfono: (239) 263-7600 Fax: (239) 263-9689 E-mail: laservice@handheld.com Brazil Hand Held Products Brazil Telephone: +55 (21) 2176-0250...

  • Page 17: Online Product Service And Repair Assistance

    Hand Held Products, Inc. ("Hand Held Products") warrants its products to be free from defects in materials and workmanship and to conform to Hand Held Products published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any Hand Held Products product which is (i) improperly installed or used;...
  • Page 18 Hand Held Products for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to Hand Held Products factory or authorized service center for inspection.
  • Page 19 Hand Held Products. Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
  • Page 20 Hand Held Products, Inc. 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208 Crdlss-QS Rev A 2/06...

This manual is also suitable for:

5620

Table of Contents