Table of Contents
Advertisement
Quick Links
American 8
Operator's Manual
Active Model: 07105A
Obsolete Models: 07032C, 07048C, 07106A
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or
attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other
personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine
before using it. If your operator cannot read this manual, have it explained fully before attempting to operate this machine.
Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el manejo o
servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
Part No. LT069200
3/14
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Clarke American 8 07105A
Summary of Contents for Clarke American 8 07105A
- Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel;...
-
Page 2: Table Of Contents
Products in such environments. The Manufacturer disclaims any responsibility to advise purchasers of any specific requirements that may be applicable to the use of the Products in such environments. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 2... -
Page 3: Operator Safety Instructions
Failure to read the Owner’s Manual prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine be- fore using it. - Page 4 Failure to read and observe all safety statements found on your machine or in this Owner’s Manual can result in seri- ous injury or damage. Read and observe all safety statements. Make sure that all labels, decals, warnings, cautions, and instructions are fastened to the machine. Get new labels from your authorized Clarke American Sanders distribu- tor.
-
Page 5: Introduction And Machine Specifications
See parts list for optional wheels. Always consult with the flooring manufacturer on the proper installation, preparation, and finishing of their product. Determine suitability of your equipment in preparing the product. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 5... -
Page 6: 230V Electrical Connection Instructions
Feet/Wire Guage (Stranded Copper) Source Voltage 0-100’ 100-250’ Use Voltage Booster If motor appears to labor or takes a considerable longer time to come up to speed reduce sanding pressure. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 6... -
Page 7: How To Transport The Machine
3. Resecure the motor to the chassis. 4. Install the fan belt. 5. Install the belt cover. 6. Reconnect the handle plug. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 7... -
Page 8: Machine Set-Up
5. Fold the other end of the abrasive over the end of the template and crease. 6. Repeat steps 4 and 5 for remaining notch. 7. Lift the drum cover. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 8... - Page 9 13. Close the cover. NOTE: When using #4 or 4½ grit abrasive, Figure 4 remove the large grains from the folded ends. To remove the grains, rub the folded ends together. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 9...
-
Page 10: How To Operate The Machine
DANGER: Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer and punch to countersink all nails before sanding floors. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 10... - Page 11 Sanding dust can spontaneously ignite and cause a fire or explosion. Empty dust into a metal container located outside of the building. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 11...
- Page 12 D. Second pass reverse, retrace second path forward, etc...for the drum width. entire room. E. Work the remaining unsanded floor in the same fashion, right to left. Figure 6 ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 12...
-
Page 13: Sanding Cuts And Sandpaper
If glazing or burning should occur immediately into a finishing cut, reduce the sanding pressure. If it should occur during a finishing cut, the abrasive has dulled and must be replaced. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 13... -
Page 14: Sander Adjustment Procedures
8. Tighten belt and secure motor to chassis. 9. Install the fan belt. 10. Install the belt guard. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 14... - Page 15 1. Loosen the locknut on the control rod. See figure 9. 2. Screw the control rod adjuster out until desired reach is found. Figure 9 3. Tighten the locknut. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 15...
-
Page 16: Routine Maintenance
Periodically check the bearings for wear or damage according to the following schedule: after 1st 1500 hrs. Idler pulley after 1st 2500 hrs. Fan shaft Arbor shaft after 1st 5000 hrs. Motor shaft after 1st 5000 hrs. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 16... -
Page 17: Troubleshooting
Drum out of round. Contact an authorized dealer. surface (close evenly spaced ) or replace the drum. Drum vibration. Change shim combination. Remove debris from surface or ends of drum. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 17... - Page 18 NOTES ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 18...
-
Page 19: Wiring Diagram
WIRING DIAGRAM ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 19... -
Page 20: Handle Assy
HANDLE ASSY ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 20... -
Page 21: Handle Assy
Washer -.319 x .586 x .078 St Lk 980638 Washer - Lt Spring Type 41707A Connector 67143A Rod Control 45608A Plug 56380639 Decal, Prop 65 [ ] = Not Shown ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 21... -
Page 22: Base Assy - 1
BASE ASSY - 1 ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 22... -
Page 23: Base Assy - 2
Motor Parts Not Illustrated 50563A End Bell 52768A Front Cover 53998A 52769A Fan Cover 51188A Bearing Front 902547 Bearing Rear 40316A Armature Assembly [ ] = Not Shown ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 23... -
Page 24: Base Assy -
BASE ASSY - 2 31 26 Optional Optional Urethane Caster Wheels Urethane Wheels 55 54 ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 24... - Page 25 Bearing, Ball Spacer NOTE 1 61355A [ ] = Not Shown NOTE 1: Only used on models 07105A & 07106A. NOTE 2: Only used on models 07032C & 07048C. ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 25...
-
Page 26: Accessories
Wrench 64415A Handle-Carrying 42201A Cordset- Hard Service 100FT 42200A Cord Set-Hard Service 68315A Template 56383241 Steel Wheel AM 8/12 Asm Kit 10243A Wheel Asm Urethane 30088A Skid Transport ® Clarke American Sanders American 8 Floor Sander Operator's Manual Page 26... -
Page 27: Chatter-Wave Prevention
Chatter - Wave Prevention Clarke American Sanders are designed and manufactured to the most rigid tolerances. However, after a finishing cut it is possible to see “chatter” or “waves”. The best guarantee to remove the chatter is to finish the floor with a rotating horizontal sander, such as Clarke American Sanders’s Sander 16. - Page 28 Clarke American Sanders specified sandpaper. PROPER CARE OF YOUR MACHINE CAN MINIMIZE CHATTER AND WAVES. V-BELTS..can cause vibration and chatter if they are of low quality. Use only belts specified by Clarke American Sand- ers. TRUCK AND CASTER WHEELS..with flat spots, out-of-roundness, or debris adhered to their surface can cause “waves”...
- Page 30 U.S. LARKE MERICAN ANDERS ANADA IMITED ARRANTY Amano Pioneer Eclipse, Inc. warrants to the original end user, each new machine, new accessories and genuine replacement parts against defects in material and workmanship under normal use and service. Our obligation under this warranty is limited to repair or replacement of the defective item at our factory or by an Authorized Service Center.
Need help?
Do you have a question about the American 8 07105A and is the answer not in the manual?
Questions and answers