Page 1
This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
Accessories ... 29 Lamp Assembly Drawing ... 30 Assembly Parts List ... 31 Gearbox Assembly Drawing & Parts List ... 32 Wiring Diagrams ... 33 Page -2 - CONTENTS OF THIS BOOK American Sanders Operator's Manual - Sander 1600DC ® Clarke...
Page 3
El libro está traducido en otros idiomas. Todas las indicaciones de dirección dadas en este libro están dadas desde la posición del operador en la parte de atrás de la máquina. Puede Ud. conseguir libros suplementarios dirigiéndose a su distribuidor Clarke American Sandeers. INDICE Instrucciones de seguridad para el operador ...
Page 4
Toutes les indications de direction figurant dans ce manuel sont visualisées depuis la position du conducteur, à l’arrière de la machine. Pour toute commande de manuels, adressez-vous à votre revendeur Clarke American Sanders. INDEX Consignes de sécurité pour l’opérateur ... 9 Présentation de la machine ...
To prevent damage to the power cord, do not let the brush, pad, pad driver or wheels touch the power cord when the machine is running. Always lift the cord over the machine. Do not pull the power cord to move the machine. American Sanders Operator's Manual - Sander 1600DC ® Clarke...
Do not use this machine to clean carpet. MACHINE INTRODUCTION The Sander 1600DC is a floor sanding machine. It can also be used for polishing, spraying, buffing and stripping. The machine can be used on wood, vinyl, terrazzo or cement floors.
Page 7
Todas las operaciones de mantenimiento o de reparación de la máquina deben ser efectuadas por técnicos cualificados. Compruebe que las fijaciones están correctamente apretadas. Haga reglajes conforme a las indicaciones dadas en el libro. American Sanders Operator's Manual - Sander 1600DC ® Clarke AVERTISSEMENT ¡...
Page 8
PRESENTACION DE LA MAQUINA Sander 1600DC Sander 1600DC es una máquina para pulir pisos. También puede ser utilizada para lustrar, pulverizar, sacar brillo y decapar. La máquina puede ser utilizada en pisos de madera, vinilo, terrazzo o cemento. Page -8 - American Sanders Operator's Manual - Sander 1600DC ®...
Page 9
être effectués par des techniciens qualifiés. Bien veiller à ce que les fixations soient correctement serrées. Effectuer les réglages conformément aux indications figurant dans le manuel. American Sanders Operator's Manual - Sander 1600DC ® Clarke AVERTISSEMENT ¡...
Page 10
PRESENTATION DE LA MACHINE Sander 1600DC Sander 1600DC est un appareil de Sablage du sol. Il peut aussi être utilisé pour le polissage, le jet et le décapelage. La machine peut être utilisée sur le bois, vinyle, terrace ou sols cimentés.
(80-100 grit). Care should be taken in selecting the grit size of the abrasive. A very fine grain will close the pores on a wood floor making admission of a stain difficult. American Sanders Operator's Manual - Sander 1600DC ® Clarke...
100 granos). Preste atención a la hora de elegir el grosor del papel abrasivo. Un papel demasiado fino podría obturar los poros de un suelo de madera lo que dificultaría la absorción de la solución colorante. American Sanders Operator's Manual - Sander 1600DC ® Clarke PREPARATION DE LA MACHINE AVANT LA MISE EN SERVICE ATTENTION: Débrancer toujours la prise de la...
Page 14
For fine scratching of surface before final coat of finish. screen mesh Page -14 - Standard Grade Part #/Qty 945342/25 945343/25 945344/25 945347/50 945349/50 945350/50 945351/50 945352/50 American Sanders Operator's Manual - Sander 1600DC ® Clarke Professional Grade Part #/Qty 945566/25 945567/25 945568/25 945569/50 945570/50 945571/50 945573/50 945574/50...
Page 15
Pour rayer la surface entre les couches de finissage. grains grille 180 Pour rayer finement la surface du parquet avant la couche finale grains de finissage American Sanders Operator's Manual - Sander 1600DC ® Clarke Grado estándar Grado profesional Sólo parte # Sólo parte #...
NOTE: For the best operating position, keep your back straight, bend only your arms. 3. Using your foot, push the locking lever down. 4. Hold the handle against your body for the best control. American Sanders Operator's Manual - Sander 1600DC ® Clarke...
Con el pie baje la palanca de bloqueo. Para controlar mejor la máquina, tenga el mango cerca del cuerpo mientras trabaja. American Sanders Operator's Manual - Sander 1600DC ® Clarke PREPARATION DE LA MACHINE...
4. Twist the ends of the string (see figure 7) and insert them into the recess of the bumper as shown in figure 8. NOTE: The skirt should be stored flat on the floor either on or off of the machine. American Sanders Operator's Manual - Sander 1600DC ® Clarke...
8. NOTA: la falda debe mantenerse sobre el piso ya sea que esté dentro o fuera de la máquina. American Sanders Operator's Manual - Sander 1600DC ® Clarke Préparation de la machine avant la...
WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. American Sanders Operator's Manual - Sander 1600DC ® Clarke...
Page 21
¡ AVISO !Use un añadido de cable de 12 AWG de sección. No use ningún añadido de más de 50 pies de largo. Nunca conecte dos añadidos. American Sanders Operator's Manual - Sander 1600DC ® Clarke MACHINES 120 V.
3. Unplug the cord at the bottom of the lamp. 4. Loosen and remove the mounting knob (see figure 11) on top of the motor. 5. Remove the lamp and reattach the mounting knob. American Sanders Operator's Manual - Sander 1600DC ® Clarke Never start machine when the handle is in the vertical posi- tion.
11) que se encuentra en la parte superior del motor. 5. Extraiga la lámpara y vuelva a conectar la perilla de montaje. American Sanders Operator's Manual - Sander 1600DC ® Clarke MISE EN SERVICE DE LA MACHINE Mise en Marche et Arrêt...
MAINTENANCE WARNING: Maintenance must be done by authorized personnel only. Maintenance Instructions Return the machine to a Clarke American Sand- ers Authorized Service Location every 12 months for maintenance inspections. MANTENIMIENTO AVISO : El mantenimiento debe ser efectuado por untécnico autorizado.
Return the machine to the nearest Clarke American Sanders Service Branch or Clarke American Sanders Authorized Service Center. For safe operation, and longer life to your Clarke Ameri- can Sanders product, use only Clarke American Sand- ers parts.
Compruebe que todas las conexiones están bien fijadas. Mande la máquina a un centro técnico autorizado Clarke Ameri- can Sanders para cualquier reparación o comprobación del sistema eléctrico.
Assembly, Pad Driver 84100A Screw, 14-10 x 1 Ref. Driver, Pad 31403A Driver Pad 10241A Shield w/connector American Sanders Operator's Manual - Sander 1600DC Clarke ® Sander 1600DC Assembly Drawing Parts List 2/03 Ref. Part No. Description Qty. 52344A 30187A...
Sander 1600DC WARNING: All electrical repairs must be performed by qualified personnel only. American Sanders Operator's Manual - Sander 1600DC Page - 33 - Clarke ®...
Page 35
® American Lincoln / Clarke , Marietta, Georgia 30062 1355 West Oak Common Lane (770) 973-5225 Clarke ® Clarke American Sanders A.L. Cook Customer Service Headquarters and Factory 2100 Highway 265 Springdale, Arkansas 72764 (479) 750-1000 Technical Service 1-800-356-7274 PRODUCT SUPPORT BRANCHES...
Page 36
WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY, SHALL BE IMPLIED. A warranty registration card is provided with your Clarke American Sanders floor machine. Return the card to assist Clarke American Sanders in providing the performance you expect from your new floor machine.