Table of Contents
Advertisement
Warranty
Each Steelcraft unit is thoroughly inspected in our Quality Assurance
department prior to delivery. In the unlikely case that you find any
material or workmanship that affects the units normal operation,
....think of your child's comfort and safety
we will repair the unit free of charge within 12 months of purchase. You
are required to present your receipt as proof of purchase.
For all concerns with your product please contact our Customer Service
team.
CUSTOMER SERVICE
1300 303 330 - Australia
0508 688 822 - New Zealand
Please read all the information carefully before using this product.
This warranty does not apply to failure due to improper care,
or normal wear and tear caused by product use. We reserve the
right to inspect the unit. You may be charged for repairs if the product
has been damaged accidentally.
Distributed by:
AUSTRALIA
BRITAX CHILDCARE PTY.LTD.
A Britax International company.
(Incorporated in Victoria)
A.B.N. 55 006 773 600
99 Derby Road, Sunshine,
Victoria 3020, Australia
Phone: (03) 9288 7288
Fax: (03) 9311 5798
Due to our continuing program of development, Britax reserves the right to alter the specifications,
colour or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: http:/www.britax.com.au or email us at custserv@britax.com.au
Due to the variations in the style and design of our products the illustrations used in this
instruction booklet are generic.
12/06
2007 Copyright Britax Childcare Pty. Ltd. Australia.
c
12
NEW ZEALAND
BRITAX CHILDCARE NZ. Limited.
A Britax International company.
101 Diana Drive, Glenfield,
Auckland 9, New Zealand.
Phone: (09) 443 0102
Fax: (09) 443 0120
4000831
WARNING:
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FURTHER REFERENCE.
BEFORE ASSEMBLING THIS COT READ & UNDERSTAND THESE INSTRUCTIONS.
INCORRECT ASSEMBLY MAY MAKE THE COT UNSAFE
DO NOT USE THIS COT IF ANY PART IS BROKEN, TORN OR MISSING.
A MATTRESS IS SUPPLIED WITH THIS COT. NO OTHER MATTRESS SHOULD BE USED.
series S600
Advertisement
Table of Contents
Related Manuals for Steelcraft S600 series
Summary of Contents for Steelcraft S600 series
- Page 1 KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FURTHER REFERENCE. The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia. The Britax trademark is the property of Britax Excelsior Limited - UK.
- Page 2 NOTES BEFORE ASSEMBLING THIS COT READ AND UNDERSTAND THE INSTRUCTIONS. INCORRECT ASSEMBLY MAY MAKE THE COT UNSAFE. KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE. WARNINGS Never leave your child unattended. Do not use your cot if any part is broken, torn or missing. Do not use or leave the cot near open fires, naked flames, electric bar fires, gas fires, stoves, heaters or barbecues.
-
Page 3: Components View
NOTES WARNING - MATTRESS SIZE This cot is made for a mattress which is 750mm wide, 1040mm long and no more than 50mm thick. Using the wrong size mattress may create hazardous gaps that could result in suffocation or could reduce the side height of the cot which may result in your child falling out from the cot. -
Page 4: To Open The Cot
ENGAGEMENT OF THE RAILS BY PUSHING DOWN Bassinet by Steelcraft - series S601L ON THEM. Change Table by Steelcraft - series S601L Holding one end of the cot clear of the ground, gently press down on the handle in the middle of the base until the base lays down flat. -
Page 5: To Use The Change Table
TO USE THE CHANGE TABLE TO OPEN THE COT (con’t) Place the mattress into the cot with its padded side Lay the change table padded side down. Connect facing up. the straight rod (tube with 2 holes at each end) to one of the corner rods. -
Page 6: To Use The Bassinet
TO FOLD THE COT (con’t) TO USE THE BASSINET Insert the 2, two-piece support rods into bassinet Rotate the handle in the middle of the base anti- clockwise and then pull base up approximately inner sleeves separately, then engage them in the 50cm.
Need help?
Do you have a question about the S600 series and is the answer not in the manual?
Questions and answers