Download Print this page

Fujitsu DL Series Driver Installation

Dot matrix printer printer driver installation guide windows 7 windows server 2008 r2.
Hide thumbs

Advertisement

Fujitsu Dot Matrix Printer
DL Series
Printer Driver Installation Guide
Rev.01: April 12, 2010
- Windows 7
- Windows Server 2008 R2

Advertisement

   Related Manuals for Fujitsu DL Series

   Summary of Contents for Fujitsu DL Series

  • Page 1

    Fujitsu Dot Matrix Printer DL Series Printer Driver Installation Guide - Windows 7 - Windows Server 2008 R2 Rev.01: April 12, 2010...

  • Page 2

    If the printer is already connected to your PC before the printer driver installation, see the section Troubleshooting in Setup in this manual. Do not use this printer driver in other printers (other than Fujitsu DL7600). Do not use Fujitsu DL7600 printer with any printer driver from other manufacturers.

  • Page 3

    Windows Server 2008 R2 Microsoft® Windows Server® 2008 R2 Standard ABOUT THE TRADEMARK Company names and product names mentioned above are registered trademarks or trademarks of each company. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 3 / 24...

  • Page 4: Printer Driver

    If the Auto Play window is not displayed, use Explorer or another application to open CD-ROM. and double click the DLSELECT.EXE file. The FUJITSU DL Series Software Setup window is displayed. From the printer driver list, select DL7600 and click the OK button.

  • Page 5

    ? is displayed, click Yes. The FUJITSU DL Series Printer Driver Package window is displayed. Click the OK button. Select a printer driver to add will be displayed.

  • Page 6

    ▪ If you do not wish to install the printer driver, select Cancel. When the procedure is ended without any printer driver installation, double click each executable program of FUJITSU DL Series Software Setup or FUJITSU DL Series Printer Driver Package again or install the printer driver through Setup method using Add a Printer Wizard.

  • Page 7

    11. Connect the printer to your PC and turn on the printer power. 12. Installing device driver software is displayed in the taskbar notification area. After a while, the message Fujitsu DL7600 Device driver software installed successfully is displayed. Note: When a USB interface is used for connection – the message Your device is ready to use is displayed instead.

  • Page 8

    Windows can't verify the publisher of this driver software is displayed, select Install this driver software anyway. c. A file copy starts. Note: Wait until the window of Procedure D. is displayed. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 8 / 24...

  • Page 9

    LPT1:(Printer Port). f. The dialog Install the printer driver is displayed. From Manufacturer, select FUJITSU. From the list of Printers, choose a model to use and click the Next button. g. The dialog Type a printer name is displayed.

  • Page 10

    Share name, Location, and Comment. j. Make sure that the message, You've successfully added Fujitsu DL7600, is displayed, and click the Finish button to terminate the wizard. Note: ▪ When multiple printer drivers have been installed, Set as the default printer is displayed.

  • Page 11

    Select Start, and then select Devices and Printers. m. Make sure that the printer driver icon is added to Printers and Faxes section. n. Restart Windows. This completes the printer driver setup. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 11 / 24...

  • Page 12

    Use the Add Printer Wizard to set up the printer driver. In this section, the setup procedure for Windows 7 is described. In the following procedure, Fujitsu DL7600 printer driver is set up. When using another printer or another printer driver, change it to your current printer or printer driver name to follow the procedure.

  • Page 13

    Use an existing port, select a temporary port such as LPT1:(Printer Port) instead. The window of Install the printer driver is displayed. Click Have Disk. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 13 / 24...

  • Page 14

    Replace the current driver. The dialog Type a printer name is displayed. Type the printer name and click Next. Note: To change the printer name, key-in the changed printer name. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 14 / 24...

  • Page 15

    (1) Not sharing : Select Do not share this printer. (2) Sharing : Select Share this printer so that others on your network can find and use it and enter Share name, Location, and Comment. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 15 / 24...

  • Page 16

    13. Make sure that the message, You've successfully added Fujitsu DL7600, is displayed, and click the Finish button to terminate the wizard. Note: ▪ When multiple printer drivers have been installed, Set as the default printer is displayed. Select as needed.

  • Page 17

    (on the right bottom of the window). In this case, follow the below procedure. In this section, Windows 7 Professional Windows (when Fujitsu DL7600 is installed) is provided as an example. When using another printer, change it to your current printer name to follow the procedure.

  • Page 18

    If the message, Do you want to allow the following program from an unknown publisher to make changes to this computer ?, is displayed in the User Account Control dialog box, click Yes. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 18 / 24...

  • Page 19

    This completes the recovery when the printer and the PC are connected before the printer driver installation. After restart, install the printer driver in the procedure described in Installing Printer Driver. Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 19 / 24...

  • Page 20: Setup Program

    The folder path exceeds the specified number of Cause: characters. Measure: Move the folder path of the Fujitsu DL Series Software Setup program to the place where the number of characters is 100 or less. The setup information file required for the Cause: installation cannot be found.

  • Page 21

    (1) The setup information file may not be present. (2) The setup information file may be destroyed. Measure: (1) Run the Fujitsu DL Series Software Setup program again. (2) Obtain the latest printer driver from Support & Downloads of the Fujitsu Isotec web site.

  • Page 22

    The folder path exceeds the specified number of Cause: characters. Measure: Move the folder path of the Fujitsu DL Series Printer Driver Package program to the place where the number of characters is 100 or less. The setup information file required for the Cause: installation cannot be found.

  • Page 23

    (1) The setup information file may not be present. (2) The setup information file may be destroyed. Measure: (1) Run the Fujitsu DL Series Printer Driver Package program again. (2) Obtain the latest printer driver from Support & Downloads of the Fujitsu Isotec web site.

  • Page 24

    Copyright © 2010 FUJITSU ISOTEC LIMITED All rights reserved. 24 / 24...

Comments to this Manuals

Symbols: 0
Latest comments: