Display P20-2S Operating Manual English Downloaded from ManualMonitor.com Manuals...
... any technical questions or problems? Please contact: ● our Hotline/Help Desk (please refer to the enclosed Help Desk list or look up the contact details on our website at: "http://ts.fujitsu.com/support/" ) ● your sales partner ● your sales office The latest information about our products, useful tips, updates etc.
Downloaded from ManualMonitor.com Manuals...
Contents Introduction............................1 Notational conventions ......................... 2 Important notes............................. 2 Safety notes..........................2 Power cable..........................4 Transport ............................4 Cleaning ............................4 CE marking........................... 4 FCC Class B Compliance Statement ................... 5 Declaration of Conformity ......................5 Energy Star Guidelines......................... 6 Disposal and recycling .........................
Contents A26361-K983-Z220-1-7619, edition 2 Downloaded from ManualMonitor.com Manuals...
A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface is required to control the FUJITSU P20-2S LCD monitor. The monitor processes the data supplied to it by the screen controller. The screen controller or the associated driver software is responsible for setting the modes (resolution and refresh rate).
FUJITSU P20-2S Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data.
If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°. ● The FUJITSU P20-2S monitor may only be operated in landscape mode (0°) and portrait mode (90°). The control buttons are located at the bottom of the monitor in landscape mode (0°) and at the left-hand side of the monitor in portrait mode (90°).
FUJITSU P20-2S Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements. ● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the outer sheath.
Fax No.: (408) 746-8299 We, Fujitsu America Inc., hereby declare that the equipment bearing the trade name and model number specified above was tested confirming to the applicable FCC Rules under the most accurate measurement standards possible, and that all the necessary steps have been taken and are in force to assure that production units of the same equipment will continue to comply with the Commissions requirements.
20 million tons of carbon dioxide into the atmosphere - the equivalent of 5 million automobiles. As an Energy Star Partner, Fujitsu Technology Solutions GmbH has determined that this product meets the Energy Star guidelines for energy efficiency.
FUJITSU P20-2S Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation.
FUJITSU P20-2S Installing an ergonomic video workstation Avoid glare from electric Windows Edge of desk lighting. Permissible reaching Avoid direct and reflected glare. sector Position the keyboard where it is easiest to reach. 0° 65° 30° 60° 30° 65° Example layout of monitor, Bearing surface for palms approx.
FUJITSU P20-2S Mounting and removing the monitor base The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base. Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor by a collar.
FUJITSU P20-2S ► Proceed according to the four steps in the illustrations to fold out the monitor base. A26361-K983-Z220-1-7619, edition 2 Downloaded from ManualMonitor.com Manuals...
FUJITSU P20-2S Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket.
Connecting cables to the monitor The monitor ports are protected by a cover. ► Remove the cover. On the FUJITSU P20-2S monitor, the DVI-D and D-SUB connectors (2 + 3) are the opposite way round. Power connector DVI-D connection socket (DIGITAL) D-SUB connection socket (ANALOG) Security slot for "Kensington Lock"...
FUJITSU P20-2S ► Insert one plug of the audio line in the AUDIO IN (5) socket on the monitor and make sure it is properly engaged. ► Plug the power cable supplied into the power connector (1) of the monitor.
FUJITSU P20-2S Adjusting portrait format The monitor can be turned from the "wide format" (landscape mode) into the "high format" position (portrait mode). ► Grasp the monitor with both hands on the right and left edge of the casing, move it into the highest position and turn it clockwise until it is in the portrait position.
FUJITSU P20-2S When you switch the computer system on, you must proceed in the following order: ► First switch on the LCD monitor with the ON/OFF switch (2). ► Then switch on the computer. If your computer has a power management function (energy-saving mode), you should read the "Notes on power management"...
FUJITSU P20-2S Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs. Choosing basic monitor settings using the supplied software...
FUJITSU P20-2S Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch.
FUJITSU P20-2S The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side). The first function (H-Position) is highlighted. ► If necessary, press the button to mark another function. ► Press the SELECT/MENU button to select the highlighted function.
FUJITSU P20-2S Adjusting size and position Calling the Image adjust setting window Adjusting the horizontal position H-Position With this function you move the picture to the left or to the right. Adjusting the vertical position V-Position With this function you move the picture up or down.
FUJITSU P20-2S Setting display of the OSD menu Calling the OSD Setup setting window Setting language for the OSD menu Language With this function you choose between English (default setting), French, German, Italian and Spanish as the language for the OSD menu.
FUJITSU P20-2S Factory Recall Activating the factory settings Displaying information Calling the Information setting window With this function the model designation, serial number, resolution, H/V frequency, input signal and polarity of the synchronisation signal are displayed. Notes on ergonomic colour adjustment If you select colours for the display in your application programmes, take note of the information below.
FUJITSU P20-2S Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the problem, please inform our help desk.
FUJITSU P20-2S Having this problem? Check the following points: Picture is wrongly adjusted ► Press the SELECT/MENU button to activate the function Factory Recall. The Auto Processing message is displayed. Picture disturbances (vertical lines) ► Press the EXIT/AUTO button to perform the auto- adjustment of the screen.
FUJITSU P20-2S Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
FUJITSU P20-2S Technical data P20-2S Dimensions and weight Visible diagonals: 51 cm Dot pitch: 0.255 mm Screen size: Width: 408 mm Height: 306 mm Maximal resolution: 1600 x 1200 Dimensions incl. Width: 444 mm monitor base: Height: 510 mm Depth:...
FUJITSU P20-2S Environmental conditions Environment class 3K2, IEC 721 Rated range of operation: 15 °C ..35 °C Humidity: 20 % ..85 % Limit range of operation: 5 °C ..35 °C Humidity: 20 % ..85 % Condensation must be avoided.
FUJITSU P20-2S Pin assignment D-SUB Meaning Meaning Video input red +5 V (DDC) Video input green Sync. earth Video input blue Earth Earth DDC-Data Earth H. sync Red video earth V. sync Green video earth DDC Clock Blue video earth...